Pierre Lovera

Two-dimensional polymer photonic crystal band-edge lasers fabricated by nanoimprint lithography

We report on the fabrication and characterization of two-dimensional polymer photonic crystal band-edge lasers operating in the visible range. The components have been fabricated in a dye chromophore-loaded polymer matrix by nanoimprint lithography. High-symmetry band-edge modes are used to generate laser emission. The experimental lasing frequencies are in good agreement with those calculated using a two-dimensional plane wave algorithm. These results demonstrate the potential of nanoimprint lithography for the fabrication of two-dimensional planar photonic crystal structures in an active medium in a one-step process.

Polarization tunable transmission through plasmonic arrays of elliptical nanopores

Polarization dependent transmission through thin gold films bearing arrays of elliptical nanopores and assembled at transparent substrates is explored. Far field transmission spectra with incident light polarized along the short and long axis of the ellipses show asymmetric peaks. Near-field finite difference time domain simulated electric field profiles suggest these features are related to Fano resonances between the (± 1, 0) Surface Plasmon Polariton mode and the ( ± 1, 0) Rayleigh Anomaly. The unique spectral signature of these samples makes them attractive for visible and near infrared tags for anti-counterfeiting applications.

A potentiometric biosensor for rapid on-site disease diagnostics

Quantitative point-of-care (POC) devices are the next generation for serological disease diagnosis. Whilst pathogen serology is typically performed by centralized laboratories using Enzyme-Linked ImmunoSorbent Assay (ELISA), faster on-site diagnosis would infer improved disease management and treatment decisions. Using the model pathogen Bovine Herpes Virus-1 (BHV-1) this study employs an extended-gate field-effect transistor (FET) for direct potentiometric serological diagnosis. BHV-1 is a major viral pathogen of Bovine Respiratory Disease (BRD), the leading cause of economic loss (

Dielectrophoretic self-assembly of polarized light emitting poly(9,9-dioctylfluorene) nanofibre arrays

2 billion annually in the US only) to the cattle and dairy industry. To demonstrate the sensor capabilities as a diagnostic tool, BHV-1 viral protein gE was expressed and immobilized on the sensor surface to serve as a capture antigen for a BHV-1-specific antibody (anti-gE), produced in cattle in response to viral infection. The gE-coated immunosensor was shown to be highly sensitive and selective to anti-gE present in commercially available anti-BHV-1 antiserum and in real serum samples from cattle with results being in excellent agreement with Surface Plasmon Resonance (SPR) and ELISA. The FET sensor is significantly faster than ELISA (<10 min), a crucial factor for successful disease intervention. This sensor technology is versatile, amenable to multiplexing, easily integrated to POC devices, and has the potential to impact a wide range of human and animal diseases.

Lasing in nanoimprinted two-dimensional photonic crystal band-edge lasers

Conjugated polymer based 1D nanostructures are attractive building blocks for future opto-electronic nanoscale devices and systems. However, a critical challenge remains the lack of manipulation methods that enable controlled and reliable positioning and orientation of organic nanostructures in a fast, reliable and scalable manner. To address this challenge, we explore dielectrophoretic assembly of discrete poly(9,9-dioctylfluorene) nanofibres and demonstrate site selective assembly and orientation of these fibres. Nanofibre arrays were assembled preferentially at receptor electrode edges, being aligned parallel to the applied electric field with a high order parameter fit (∼ 0.9) and exhibiting an emission dichroic ratio of ∼ 4.0. As such, the dielectrophoretic method represents a fast, reliable and scalable self-assembly approach for manipulation of 1D organic nanostructures. The ability to fabricate nanofibre arrays in this manner could be potentially important for exploration and development of future nanoscale opto-electronic devices and systems.

High aspect ratio nano-fabrication of photonic crystal structures on glass wafers using chrome as hard mask

We demonstrate optically pumped polymer band-edge lasers based on a two-dimensional photonic crystal slab fabricated by nanoimprint lithography (NIL). Lasing was obtained at the photonic band-edge, where the light exhibits a low group velocity at the Γ point of the triangular lattice photonic crystal band structure. The active medium was composed of a dye chromophore-loaded polymer matrix directly patterned in a single step by nanoimprint lithography. Plane-wave and finite difference time domain algorithms were used to predict experimental lasing frequencies and the lasing thresholds obtained at different Γ points. A low laser threshold of 3 μJ/mm2 was achieved in a defect-free photonic crystal thus showing the suitability of nanoimprint lithography to produce cost-efficient optically pumped lasers.

Low-cost silver capped polystyrene nanotube arrays as super-hydrophobic substrates for SERS applications.

Wafer-scale nano-fabrication of silicon nitride (Si x N y ) photonic crystal (PhC) structures on glass (quartz) substrates is demonstrated using a thin (30 nm) chromium (Cr) layer as the hard mask for transferring the electron beam lithography (EBL) defined resist patterns. The use of the thin Cr layer not only solves the charging effect during the EBL on the insulating substrate, but also facilitates high aspect ratio PhCs by acting as a hard mask while deep etching into the Si x N y . A very high aspect ratio of 10:1 on a 60 nm wide grating structure has been achieved while preserving the quality of the flat top of the narrow lines. The presented nano-fabrication method provides PhC structures necessary for a high quality optical response. Finally, we fabricated a refractive index based PhC sensor which shows a sensitivity of 185 nm per RIU.

Multi-colour emission from dye doped polymeric nanotubes by host–guest energy transfer

In this paper, we describe the fabrication, simulation and characterization of dense arrays of freestanding silver capped polystyrene nanotubes, and demonstrate their suitability for surface enhanced Raman scattering (SERS) applications. Substrates are fabricated in a rapid, low-cost and scalable way by melt wetting of polystyrene (PS) in an anodized alumina (AAO) template, followed by silver evaporation. Scanning electron microscopy reveals that substrates are composed of a dense array of freestanding polystyrene nanotubes topped by silver nanocaps. SERS characterization of the substrates, employing a monolayer of 4-aminothiophenol (4-ABT) as a model molecule, exhibits an enhancement factor of ∼1.6 × 10(6), in agreement with 3D finite difference time domain simulations. Contact angle measurements of the substrates revealed super-hydrophobic properties, allowing pre-concentration of target analyte into a small volume. These super-hydrophobic properties of the samples are taken advantage of for sensitive detection of the organic pollutant crystal violet, with detection down to ∼400 ppt in a 2 μl aliquot demonstrated.

Probe based manipulation and assembly of nanowires into organized mesostructures

Emission chromaticity tuning in polymeric nanotubes was achieved by transfer of excitation energy from a polymer host matrix poly(N-vinylcarbazole) (PVK) to incorporated luminescent chromophore guests (Coumarin 6 and Nile red). Nanotubes were synthesized in densely packed arrays by solution assisted template wetting. Un-doped PVK tubes displayed blue luminescence while Coumarin 6 and Nile red doped tubes exhibited characteristic green and red luminescence with minimal PVK emission, confirming effective host–guest energy transfer. The emission spectral data of single nanotubes, and indicated that, by varying the type and relative concentrations of the dopant dyes, nanotube emission could be tuned from the blue, through green and yellow, to the red and, ultimately, to white, while maintaining excellent color purity.

Nonlinear refractive index and three-photon absorption coefficient of poly(9,9-dioctylfluorence)

A convenient approach to patterning inorganic and organic nanowires using a novel probe manipulator is presented. The system utilizes an electrochemically etched tungsten wire probe mounted onto a 3D actuator that is directed by a 3D controller. When it is engaged by the user, the movement of the probe and the forces experienced by the tip are simultaneously reported in real time. Platinum nanowires are manipulated into organized mesostructures on silicon chip substrates. In particular, individual nanowires are systematically removed from aggregates, transferred to a chosen location, and manipulated into complex structures in which selected wires occupy specific positions with defined orientations. Rapid prototyping of complex mesostructures, by pushing, rotating and bending conjugated polymer, i.e., polyfluorene, nanowires into various configurations, is also achieved. By exploiting the strong internal axial alignment of polymer chains within the polyfluorene nanowires, mesostructures tailored to exhibit distinctly anisotropic optical properties, such as birefringence and photoluminescence dichroism, are successfully assembled on fused silica substrates.