Pranab Sarker

Electronic structure, photovoltage, and photocatalytic hydrogen evolution with p-CuBi2O4 nanocrystals

As a visible light active p-type semiconductor, CuBi2O4 is of interest as a photocatalyst for the generation of hydrogen fuel from water. Here we present the first photovoltage and photocatalytic measurements on this material and DFT results on its band structure. Single crystalline CuBi2O4 nanoparticles (25.7 ± 4.7 nm) were synthesized from bismuth and cupric nitrate in water under hydrothermal conditions. Powder X-ray diffraction (XRD) confirms the CuBi2O4 structure type and UV-Vis spectroscopy shows a 1.75 eV optical band gap. Surface photovoltage (SPV) measurements on CuBi2O4 nanoparticle films on fluorine doped tin oxide yield 0.225 V positive photovoltage at >1.75 eV photon energy confirming holes as majority carriers. The photovoltage is reversible and limited by light absorption. When dispersed in 0.075 M aqueous potassium iodide solution, the CuBi2O4 particles support photochemical hydrogen evolution of up to 16 μmol h−1 under ultraviolet but not under visible light. Based on electrochemical scans, CuBi2O4 is unstable toward reduction at −0.2 V, but a pH-dependent photocurrent of 6.45 μA cm−2 with an onset potential of +0.75 V vs. NHE can be obtained with 0.01 M Na2S2O8 as a sacrificial electron acceptor. The photoelectrochemical properties of CuBi2O4 can be explained on the basis of the band structure of the material. DFT calculations show that the valence and conduction band edges arise primarily from the combination of O 2p and Cu 3d orbitals, respectively, with additional contributions from Cu 3d and Bi 6s orbitals just below the Fermi level. Trapping of photoelectrons in the Cu 3d band is the cause for reductive photocorrosion of the material, while the p-type conductivity arises from copper vacancy states near the VB edge. These findings provide an improved understanding of the photophysical properties of p-CuBi2O4 and its limitations as a proton reduction photocatalyst.

Time- and energy-efficient solution combustion synthesis of binary metal tungstate nanoparticles with enhanced photocatalytic activity.

In the search for stable and efficient photocatalysts beyond TiO2 , the tungsten-based oxide semiconductors silver tungstate (Ag2 WO4 ), copper tungstate (CuWO4 ), and zinc tungstate (ZnWO4 ) were prepared using solution combustion synthesis (SCS). The tungsten precursors influence on the product was of particular relevance to this study, and the most significant effects are highlighted. Each samples photocatalytic activity towards methyl orange degradation was studied and benchmarked against their respective commercial oxide sample obtained by solid-state ceramic synthesis. Based on the results herein, we conclude that SCS is a time- and energy-efficient method to synthesize crystalline binary tungstate nanomaterials even without additional excessive heat treatment. As many of these photocatalysts possess excellent photocatalytic activity, the discussed synthetic strategy may open sustainable materials chemistry avenues to solar energy conversion and environmental remediation.

Photocatalytic Generation of Syngas Using Combustion‐Synthesized Silver Bismuth Tungstate

Silver bismuth tungstate (AgBiW(2)O(8)) nanoparticles were prepared for the first time by solution combustion synthesis by using the corresponding metal nitrates as the precursor and urea as the fuel. These nanoparticles were subsequently modified with Pt catalyst islands using a photocatalytic procedure and used for the photogeneration of syngas (CO+H(2)). Formic acid was used for this purpose for the in situ generation of CO(2) and its subsequent reduction to CO. In the absence of Pt modification, H(2) was not obtained in the gas products evolved. These results were compared with those obtained with acetic acid in place of formic acid. The combustion process was simulated by thermogravimetry and the synthesized powder was characterized using transmission electron microscopy, diffuse reflectance UV/Vis spectroscopy, X-ray diffraction, surface area measurements, and X-ray photoelectron spectroscopy. Tauc plots derived from the diffuse reflectance data yielded an optical band gap of 2.74 eV. The photocatalytic activity of these nanoparticles was superior to a sample prepared by solid-state synthesis. Mechanistic aspects are finally presented, as are structural models and electronic calculations, using density functional theory (DFT).

Predicting a new photocatalyst and its electronic properties by density functional theory

A new material CuBiW2O8 is reported here which is suitable for photocatalysts for solar-to-hydrogen generation by splitting water through photoelectrochemical approach. By density functional theory total energy calculations along with extensive mineral database search of relevant oxides, the crystal structures of CuBiW2O8 has been determined, which agrees well with the experimental result. We have analyzed the thermodynamical stability of this material. Its stability was found to be comparable to other well-known oxides, such as CuWO4. The band structure calculation reveals that it has a suitable band gap. In addition to this, density of states and optical absorption calculations show favorable features of a photocatalyst.

Theoretical limits on the stability of single-phase kesterite-Cu2ZnSnS4

The single-phase stability of Cu2ZnSnS4 (CZTS), after an intrinsic defect was incorporated in it, has been examined here for the first time based on ab initio calculations. The stability analysis of such a non-stoichiometric-defect incorporated CZTS shows that the single-phase formation is unlikely at thermodynamic equilibrium conditions. In addition, the effective growth condition of CZTS is determined and quantified for all the elements (Cu-poor, Zn-rich, Sn-poor, and S-rich) to extract maximum photovoltaic efficiency from CZTS. These conditions promote (i) spontaneous formation of Cu vacancy (VCu), which might benefit p-type conduction, and (ii) the co-existence of ZnS while suppressing other harmful defects and secondary phases. Further, the results presented here explain the unavailability of single-phase CZTS to date.

Photoelectrochemical Properties and Behavior of α-SnWO4 Photoanodes Synthesized by Hydrothermal Conversion of WO3 Films

Metal oxides with moderate band gaps are desired for efficient production of hydrogen from sunlight and water via photoelectrochemical (PEC) water splitting. Here, we report an α-SnWO4 photoanode synthesized by hydrothermal conversion of WO3 films that achieves photon to current conversion at wavelengths up to 700 nm (1.78 eV). This photoanode is promising for overall PEC water-splitting because the flat-band potential and voltage of photocurrent onset are more negative than the potential of hydrogen evolution. Furthermore, the photoanode utilizes a large portion of the solar spectrum. However, the photocurrent density reaches only a small fraction of that which is theoretically possible. Density functional theory based thermodynamic and electronic structure calculations were performed to elucidate the nature and impact of defects in α-SnWO4 prepared by this synthetic route, from which hole localization at Sn-at-W antisite defects was determined to be a likely cause for the poor photocurrent. Measurements further showed that the photocurrent decreases over time due to surface oxidation, which was suppressed by improving the kinetics of hole transfer at the semiconductor/electrolyte interface. Alternative synthetic methods and the addition of protective coatings and/or oxygen evolution catalysts are suggested to improve the PEC performance and stability of this promising α-SnWO4 material.

Predicting a quaternary tungsten oxide for sustainable photovoltaic application by density functional theory

A quaternary oxide, CuSnW2O8 (CTTO), has been predicted by density functional theory (DFT) to be a suitable material for sustainable photovoltaic applications. CTTO possesses band gaps of 1.25 eV (indirect) and 1.37 eV (direct), which were evaluated using the hybrid functional (HSE06) as a post-DFT method. The hole mobility of CTTO was higher than that of silicon. Further, optical absorption calculations demonstrate that CTTO is a better absorber of sunlight than Cu2ZnSnS4 and CuInxGa1−xSe2 (x = 0.5). In addition, CTTO exhibits rigorous thermodynamic stability comparable to WO3, as investigated by different thermodynamic approaches such as bonding cohesion, fragmentation tendency, and chemical potential analysis. Chemical potential analysis further revealed that CTTO can be synthesized at flexible experimental growth conditions, although the co-existence of at least one secondary phase is likely. Finally, like other Cu-based compounds, the formation of Cu vacancies is highly probable, even at Cu-rich grow...

Electronic structure study of N, O related defects in GaP for photoelectrochemical applications

It is known that the stability of GaP as a photocatalyst in electrolytes can be enhanced by nitrogen doping, GaP:N. However, both GaP (indirect gap) and GaP:N (direct gap) have poor optical absorption properties across their fundamental band gap. To enhance optical absorption as well as the photocurrent, we have examined by density functional theory the favorability of oxygen and hydrogen impurities in conjunction with N doping in bulk GaP. It has been found here that O-related defects are more favorable, whereas H with N substitution is not very favorable. These O–N related defects create a global effect in the GaP lattice by both volume and band gap reduction. Enhancement of optical absorption was also found due to these types of complex doping.