Rachael L Trautman

Can synchrotron micro-x-ray fluorescence spectroscopy be used to map the distribution of cadmium in soil particles?

Plants take up cadmium (Cd) from the soil, and the concentration of Cd in some plant products is a health concern. Plant uptake of Cd is poorly predicted by its concentration in soils; consequently, there is interest in the binding and distribution of Cd in soil. Synchrotron micro-X-ray fluorescence spectroscopy (micro-XRFS) is the most sensitive method of observing this distribution. We used beam-line 2-ID-D of the Advanced Photon Source (APS), Argonne, to test whether this technique could map the Cd distribution in 5 soils from Greater Sydney that contained 0.3-6.4 mg Cd/kg. A subsample of one soil was spiked to contain ∼100 mg Cd/kg. Cadmium was readily mapped in the Cd-enriched subsample, whereas in the unamended soils, only one Cd-rich particle was found; that is, sensitivity generally limited Cd mapping. We also examined a sample of Nauru phosphorite, which was a primary source of much of the Cd in farm soils on the peri-urban fringe of Greater Sydney. The phosphorite contained ∼100 mg Cd/kg and the Cd was relatively uniformly distributed, supporting the findings of an earlier study on an apatite from Africa. The micro-XRFS at beam-line 2-ID-D of the APS can be reconfigured to increase the sensitivity at least 10-fold, which may allow the distribution of Cd and its elemental associations to be mapped in particles of most agricultural soils and facilitate other spectroscopic investigations.

Sol-Gel Synthesis of Complex Titanates in Micro-Emulsions

Amorphous precursor nanopowders of zirconolite (CaZrTi2O7) were prepared using a water-in-oil micro-emulsion synthesis, with Ti(OiC3H7)4, Zr(OnC3H7)4 and either Ca(OC2H5)2 or an aqueous Ca(NO3)2 solution as precursors. The stoichiometry and structural evolution of the nanoparticles were investigated using a range of techniques, including ICP-MS, TEM, gas adsorption and vibrational spectroscopy. The use of Ca(OC2H5)2 led to slightly sub-stoichiometric nanopowders (CaxZrTi2O6+x, x = 0.8), following washing. Lower values of x were obtained in the washed nanopowders when using Ca(NO3)2, with x = 0.004, 0.022 or 0.52 at pH 2, 7 or 13, respectively. In the latter system, a comparison between the washed and unwashed nanopowders revealed that 25% of the calcium was lost during washing. The Ca(NO3)2 was found to form unstable tetraamine complexes within the reverse micelles at high pH, which transformed into Ca(OH)2 on ageing. The Ca(OH)2 can then interact with the hydrolysed titanium/zirconium alkoxides, and thus be integrated chemically into the final nanoparticle structure.

Characterisation of Geopolymers for the Immobilisation of Intermediate Level Waste

Geopolymers are made by adding aluminosilicates to concentrated alkali solutions for dissolution and subsequent polymerisation to take place. Their physical behaviour is similar to that of Portland cement and they have been considered as a possible improvement on cement for several applications including as media for the encapsulation of hazardous or low/intermediate level radioactive waste. We studied in detail a commercial geopolymer to try to get a better understanding of geopolymers in order to enhance its leach resistance for immobilisation of intermediate level radioactive waste. We also briefly investigated two types of experimental geopolymers, one made with a metakaolinite and another from fly ash as the aluminosilicate source. The commercial geopolymer paste had an apparent porosity of 26% and it was possible to reduce it to 17% by adding ∼ 30 weight % foundry sand. The apparent porosities of the geopolymer made from metakaolinite and from fly ash were 13% and 26% respectively. X-ray powder diffraction showed in the three geopolymers, an amorphous phase (deduced by the presence of a very broad diffuse peak centred at a d-spacing of ∼ 0.32 nm), quartz and other minor phases. The energy dispersive spectroscopic analysis under the scanning electron microscope confirmed these. Magic angle spinning nuclear magnetic resonance data from the samples showed Al to be mainly in 4-fold coordination and Si sites varying from Q0 to Q4 coordination as also found by other researchers. 23 Na spectra indicated that the Na was mainly in the pore water. The 133 Cs spectra showed a strong possibility of Cs being mainly bound in the structure while a small amount could still be in the pore water. The initial leach tests showed alkalis were leached out at rates of several orders of magnitude more than the Al and Si network ions. The most likely reason is that a significant alkali inventory is in the pore water. To remove pore water and incorporate simulated radionuclides such as Cs in the network the commercial geopolymer was heated up to 1200°C. Differential thermal/thermogravimetric analysis showed the loss of water occurs in three stages and most had been lost by 700°C. These results are in broad agreement with the Infra red spectra obtained for samples heated over the temperature range 30–900°C. The broad water band intensity in the range 2600-30-900°C. The broad water band intensity in the range 2600–3800 cm −1 decreased steadily with temperature although a small fraction remained even after heating to 500°C. The silanol band had disappeared at 800°C, and the 3619 cm−1 band (due to OH) virtually disappeared by 900°C.Copyright