Raymond Zeeman

Crosslinking and modification of dermal sheep collagen using 1,4-butanediol diglycidyl ether

Crosslinking of dermal sheep collagen (DSC) was accomplished using 1, 4-butanediol diglycidyl ether (BDDGE). At pH values > 8.0, epoxide groups of BDDGE will react with amine groups of collagen. The effects of BDDGE concentration, pH, time, and temperature were studied. Utilization of a 4-wt % BDDGE instead of 1-wt % resulted in a faster reaction. Whereas similar values of shrinkage temperature were obtained, fewer primary amine groups had reacted at a lower BDDGE concentration, which implies that the crosslinking reaction had a higher efficacy. An increase in pH from 8.5 to 10.5 resulted in a faster reaction but reduced crosslink efficacy. Furthermore, an increase in reaction temperature accelerated the reaction without changing the crosslink efficacy. Crosslinking under acidic conditions (pH < 6.0) evoked a reaction between epoxide groups and carboxylic acid groups of collagen. Additional studies showed that no oligomeric crosslinks could be formed. However, hydrolysis of the epoxide groups played a role in the crosslink mechanism especially under acidic reaction conditions. The macroscopic properties of these materials were dependent on the crosslinking method. Whereas a flexible and soft tissue was found if crosslinking was performed at pH < 6.0, a stiff sponge was obtained under alkaline conditions. Reaction of DSC with a monofunctional compound (glycidyl isopropyl ether) led to comparable trends in reaction rate and in similar macroscopical differences in materials as observed with BDDGE.

Characterization and biocompatibility of epoxy-crosslinked dermal sheep collagens

Dermal sheep collagen (DSC), which was crosslinked with 1, 4-butanediol diglycidyl ether (BD) by using four different conditions, was characterized and its biocompatibility was evaluated after subcutaneous implantation in rats. Crosslinking at pH 9.0 (BD90) or with successive epoxy and carbodiimide steps (BD45EN) resulted in a large increase in the shrinkage temperature (T(s)) in combination with a clear reduction in amines. Crosslinking at pH 4.5 (BD45) increased the T(s) of the material but hardly reduced the number of amines. Acylation (BD45HAc) showed the largest reduction in amines in combination with the lowest T(s). An evaluation of the implants showed that BD45, BD90, and BD45EN were biocompatible. A high influx of polymorphonuclear cells and macrophages was observed for BD45HAc, but this subsided at day 5. At week 6 the BD45 had completely degraded and BD45HAc was remarkably reduced in size, while BD45EN showed a clear size reduction of the outer DSC bundles; BD90 showed none of these features. This agreed with the observed degree of macrophage accumulation and giant cell formation. None of the materials calcified. For the purpose of soft tissue replacement, BD90 was defined as the material of choice because it combined biocompatibility, low cellular ingrowth, low biodegradation, and the absence of calcification with fibroblast ingrowth and new collagen formation.

The kinetics of 1,4-butanediol diglycidyl ether crosslinking of dermal sheep collagen

Dermal sheep collagen was crosslinked with 1,4-butanediol diglycidyl ether (BDDGE) or modified with glycidyl isopropyl ether (PGE). The reduction in amine groups as a function of time was followed to study the overall reaction kinetics of collagen with either BDDGE or PGE. Linearization of the experimental data resulted in a reaction order of 2 with respect to the amine groups in the PGE masking reaction, whereas a reaction order of 2.5 was obtained in the BDDGE crosslinking reaction. The reaction orders were independent of the pH in the range of 8.5-10.5 and the reagent concentration (1-4 wt %). The reaction order with respect to epoxide groups was equal to 1 for both reagents. As expected, the reaction rate was favored by a higher reagent concentration and a higher solution pH. Because the BDDGE crosslinking reaction occurs via two distinct reaction steps, the content of pendant epoxide groups in the collagen matrix was determined by treating the collagen with either O-phosphoryl ethanolamine or lysine methyl ester. The increase in either phosphor or primary amine groups was related to the content of pendant groups. Crosslinking at pH 9.0 resulted in a low reaction rate but in a high crosslink efficacy, especially after prolonged reaction times. A maximum concentration of pendant epoxide groups was detected after 50 h. Reaction at pH 10.0 was faster, but a lower crosslinking efficacy was obtained. At pH 10.0, the ratio between pendant epoxide groups and crosslinks was almost equal to 1 during the course of the crosslinking reaction.

In vivo behavior of epoxy-crosslinked porcine heart valve cusps and walls

Calcification limits the long-term durability of xenograft glutaraldehyde-crosslinked heart valves. In this study, epoxy-crosslinked porcine aortic valve tissue was evaluated after subcutaneous implantation in weanling rats. Non-crosslinked valves and valves crosslinked with glutaraldehyde or carbodiimide functioned as control. Epoxy-crosslinked valves had somewhat lower shrinkage temperatures than the crosslinked controls, and within the series also some macroscopic and microscopic differences were obvious. After 8 weeks implantation, cusps from non-crosslinked valves were not retrieved. The matching walls were more degraded than the epoxy- and control-crosslinked walls. This was observed from the higher cellular ingrowth with fibroblasts, macrophages, and giant cells. Furthermore, non-crosslinked walls showed highest numbers of lymphocytes, which were most obvious in the capsules. Epoxy- and control-crosslinked cusps and walls induced lower reactions. Calcification, measured by von Kossa-staining and by Ca-analysis, was always observed. Crosslinked cusps calcified more than walls. Of all wall samples, the non-crosslinked walls showed the highest calcification. It is concluded that epoxy-crosslinked valve tissue induced a foreign body and calcification reaction similar to the two crosslinked controls. Therefore, epoxy-crosslinking does not represent a solution for the calcification problem of heart valve bioprostheses.

Crosslinking of porcine aortic leaflets with butane‐1,4‐diol diglycidyl ether

Currently, efforts are being made to reduce xenograft calcification and to optimize biomechanical properties by applying different crosslinking methods and techniques. Porcine aortic leaflets could be stabilized with a bisepoxy compound, butane-1,4-diol diglycidyl ether (BDDGE), under acidic (pH 4.5) or alkaline conditions (pH > 8.5). Maximum values of the shrinkage temperature (83°C), which are comparable to glutaraldehyde-crosslinked materials, are achieved at pH 9.0 and 10.0 within 48 h with a BDDGE concentration of 4 wt6percnt;. The crosslinking efficacy decreased at higher pH values or at prolonged reaction times due to a higher proportion of one-side or masking reactions. Crosslinking of aortic leaflets at pH 4.5, which consisted in a reaction between the epoxide groups of BDDGE and the carboxylic acid groups of the tissue, afforded crosslinked material with a shrinkage temperature of 76°C after 7 days of reaction.