Ren-Jang Wu

Titanium dioxide-mediated heterogeneous photocatalytic degradation of terbufos: Parameter study and reaction pathways

The photocatalytic degradation of terbufos in aqueous suspensions was investigated by using titanium dioxide (TiO(2)) as a photocatalyst. About 99% of terbufos was degraded after UV irradiation for 90 min. Factors such as pH of the system, TiO(2) dosage, and presence of anions were found to influence the degradation rate. Photodegradation of terbufos by TiO(2)/UV exhibited pseudo-first-order reaction kinetics, and a reaction quantum yield of 0.289. The electrical energy consumption per order of magnitude for photocatalytic degradation of terbufos was calculated and showed that a moderated efficiency (E(EO)=71 kWh/(m(3)order)) was obtained in TiO(2)/UV process. To obtain a better understanding of the mechanistic details of this TiO(2)-assisted photodegradation of terbufos with UV irradiation, the intermediates of the processes were separated, identified, and characterized by the solid-phase microextraction (SPME) and gas chromatography/mass spectrometry (GC/MS) technique. The probable photodegradation pathways were proposed and discussed.

In situ prepared polypyrrole for low humidity QCM sensor and related theoretical calculation

In situ preparation of polypyrrole (Ppy) by photo-polymerization coated on a quartz crystal microbalance (QCM) as a low humidity sensor was reported. Different concentrations of Ppy films say 0wt.% (as blank), 0.1, 1, and 10wt.% were investigated to measure humidity concentrations between 14.7 and 5412.5ppm(v). The adsorption/desorption behavior was also examined at humidity concentration 510.2ppm(v). The sensitivities of 0, 0.1 and 1wt.% Ppy films at 51.5ppm(v) were 0.143, 0.219 and 0.427, respectively. For 1wt.% Ppy, the highest sensitivity was obtained. The slope and correlation coefficients (R(2)) for 1wt.% Ppy at the ranges of 14.7-898.6ppm(v) were 0.0646 and 0.9909, respectively. A series of molecular simulations have been carried out to calculate bond energy for the water molecule interaction with Ppy, which was found to be approximately 3kcal/mol indicating the existence of hydrogen bonding during the sorption process. Based on Langmuir isotherm adsorption assumption, for 0.1 and 1wt.% Ppy films, the association constants were 2606.30 and 5792.98, respectively. This larger association constant for 1wt.% Ppy film explains higher sensitivity.

Prepared Reticulated Nickel Hydroxide for Sensing Urea by Differential Pulse Voltammetry

A urea sensor base on reticulated nickel hydroxide is prepared by hydrothermal way and operated by differential pulse voltammetry method. The reticulated nickel hydroxide has been successfully synthesized by a hydrothermal method and has been characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FTIR). The Ni(OH)2 sensor exhibits a higher sensor response (S) of 7.1 than NiO and Au sensing materials to 0.05 M urea concentration at 0.62 V. Various concentration of urea from 0.1 mM to 50 mM are performed on Ni(OH)2, and the sensor response are increased from 1.1 to 7.1 by differential pulse voltammetry (DPV) method. The urea detection limit is measured as 0.1 μM in this system. In addition, the Ni(OH)2 sensor exhibited good reproducibility and short term stability, and the response exhibits no obvious changes after 20 days tests. A possible sensing mechanism of Ni(OH)2 urea sensor is presented.