Renato Luiz Siqueira

Poly(borosiloxanes) as precursors for carbon fiber ceramic matrix composites

Ceramic matrix composites (CMCs), constituted of a silicon boron oxycarbide (SiBCO) matrix and unidirectional carbon fiber rods as a reinforcement phase, were prepared by pyrolysis of carbon fiber rods wrapped in polysiloxane (PS) or poly(borosiloxane) (PBS) matrices. The preparation of the polymeric precursors involved hydrolysis/condensation reactions of alkoxysilanes in the presence and absence of boric acid, with B/Si atomic ratios of 0.2 and 0.5. Infrared spectra of PBS showed evidence of Si-O-B bonds at 880 cm-1, due to the incorporation of the crosslinker trigonal units of BO3 in the polymeric network. X ray diffraction analyses exhibited an amorphous character of the resulting polymer-derived ceramics obtained by pyrolysis up to 1000 °C under inert atmosphere. The C/SiBCO composites showed better thermal stability than the C/SiOC materials. In addition, good adhesion between the carbon fiber and the ceramic phase was observed by SEM microscopy

Bioactivity and cell proliferation in radiopaque gel-derived CaO–P2O5–SiO2–ZrO2 glass and glass–ceramic powders

In this study, 10 mol% ZrO2 was added to a 27CaO-5P2O5-68SiO2 (mol%) base composition synthesized via a simple sol-gel method. This composition is similar to that of a frequently investigated bioactive gel-glass. The effects of ZrO2 on the in vitro bioactivity and MG-63 cell proliferation of the glass and its derivative polycrystalline (glass-ceramic) powder were investigated. The samples were characterized using thermo-gravimetric and differential thermal analysis (TG/DTA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) coupled to energy dispersive X-ray spectroscopy (EDS). Release of Si, Ca, P and Zr into simulated body fluid (SBF) was determined by inductively coupled plasma (ICP). Upon heat treatment at 1000 °C, the glass powder crystallized into an apatite-wollastonite-zirconia glass-ceramic powder. Hydroxycarbonate apatite (HCA) formation on the surface of the glass and glass-ceramic particles containing ZrO2 was confirmed by FTIR and SEM. Addition of ZrO2 to the base glass composition decreased the rate of HCA formation in vitro from one day to three days, and hence, ZrO2 could be employed to control the rate of apatite formation. However, the rate of HCA formation on the glass-ceramic powder containing ZrO2 crystal was equal to that in the base glassy powder. Tests with a cultured human osteoblast-like MG-63 cells revealed that the glass and glass-ceramic materials stimulated cell proliferation, indicating that they are biocompatible and are not cytotoxic in vitro. Moreover, zirconia clearly increased osteoblast proliferation over that of the Zr-free samples. This increase is likely associated with the lower solubility of these samples and, consequently, a smaller variation in the media pH. Despite the low solubility of these materials, bioactivity was maintained, indicating that these glassy and polycrystalline powders are potential candidates for bone graft substitutes and bone cements with the special feature of radiopacity.

Evaluation of antibiofilm and mechanical properties of new nanocomposites based on acrylic resins and silver vanadate nanoparticles.

OBJECTIVE The purpose of this study was evaluate, for the first time, the impact of incorporation of nanostructured silver vanadate (β-AgVO3) in antibiofilm and mechanical properties of dental acrylic resins (poly(methyl methacrylate), PMMA). DESIGN The β-AgVO3 was synthesized and characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, and microanalysis (SEM/EDS). Resins specimens were prepared with 0-10% wt.% β-AgVO3 and characterized by SEM, XRD and optical microscopy. The antibiofim activity of the samples against Candida albicans and Streptococcus mutans was investigated by XTT reduction test, colony-forming units (CFUs), and confocal laser scanning microscopy (CLSM). The flexural strength, hardness, and surface roughness of the samples containing β-AgVO3 were compared with the pure PMMA matrix. RESULTS The incorporation of 10% β-AgVO3 significantly reduced the metabolic activity of C. albicans and S. mutans (p<0.05). There was a reduction in microbial load (CFU/mL) of microorganisms for the different concentrations used (p<0.05), which was confirmed by confocal microscopy. The addition of β-AgVO3 did not change the mechanical properties of hardness and surface roughness of the resins (p>0.05). However, flexural strength decreased with the addition of amounts greater than 1% (p<0.05). CONCLUSIONS β-AgVO3 additions in dental acrylic resin may have an impact on inhibition of biofilm of main microorganisms associated with dental prostheses. However, the viability of clinical use should be evaluated in function of changed promoted in some mechanical properties.

Biosilicato®: histórico de uma vitrocerâmica brasileira de elevada bioatividade

This paper presents a historical of the Biosilicate®, a bioactive glass-ceramic developed at the Vitreous Materials Laboratory of the Federal University of Sao Carlos, Brazil. After decades of study accomplished with bioactive glasses and glass-ceramics, Biosilicate® results from a natural evolution and has similar bioactivity index, but far superior mechanical properties than of all bioactive glasses. Biosilicate® is almost fully crystalline and also exhibits much higher bioactivity than all the currently commercially available bioactive glass-ceramics. Due to its special characteristics, Biosilicate® has been successfully tested for several medical and dental applications as we thoroughly discuss in this review paper.

Bioactive gel-glasses with distinctly different compositions: Bioactivity, viability of stem cells and antibiofilm effect against Streptococcus mutans

In this study, an evaluation was performed to determine the in vitro bioactivity, viability of stem cells, and antibiofilm effect against Streptococcus mutans of two bioactive gel-glass 60SiO2-36CaO-4P2O5 (BG-A) and 80SiO2-15CaO-5P2O5 (BG-B) compositions. Both materials were bioactive and undergo the formation of hydroxycarbonate apatite (HCA) on their surfaces when immersed in simulated body fluid (SBF) after 12h, but the BG-A composition showed a more significant formation rate. The pH variation of the samples during the test in SBF indicated that an abrupt change had occurred for the BG-A composition within the first few hours, and the pH was subsequently maintained over time, supporting its stronger antibacterial effects against S. mutans. For the in vitro viability test using mesenchymal stem cells (MSCs), the BG-B showed significantly higher cell viability compared to the BG-A composition at concentrations of 0.125, 1.25 and 12.50mg/mL for 2days. These results indicated that the higher solubility of the BG-A glass favors bioactivity and antibacterial effects. However, as a result of rapid degradation, the increase in the concentration of ions in the cell culture medium was not favorable for cell proliferation. Thus, by varying the composition of glasses, and consequently their dissolution rate, it is possible to favor bioactivity, antimicrobial activity or stem cell proliferation for a particular application of interest.

Bioglass® and resulting crystalline materials synthesized via an acetic acid-assisted sol–gel route

In this study, we report on the synthesis of a bioactive glass powder with the original 45S5 composition (Bioglass®) by means of an acetic acid-assisted sol–gel route. A glassy material was obtained after the gels underwent a thermal stabilization treatment at 600 °C for 3 h. Above this temperature, the heat-treated gels crystallized partially, forming a sodium-calcium-silicate Na2CaSi2O6 phase. Even after crystallization, this material showed in vitro bioactivity in simulated body fluid after 12 h, when the formation of hydroxycarbonate apatite on the material surface was identified by X-ray diffraction. Not surprisingly, microbiological assays revealed that these gel-derived materials appear to have an antibacterial effect against Pseudomonas aeruginosa (ATCC 27853)—a Gram-negative bacterium that is noted for its environmental survival versatility, ability to produce biofilm and resistance to some antibiotics. Thus, using common precursors that are widely available, relatively cheap, simple to use, and which result in gels with low stabilization temperature, it was possible to explore the versatility of sol–gel processing to obtain the golden standard 45S5 bioglass.Graphical Abstract

The Protective Role of Poly(Borosiloxanes)-Derived Ceramics in Carbon Fiber Composites

This work reports the synthesis and thermal characterization of poly(borosiloxanes) (PBS) derived from methyltrietoxysilane (MTES) and vinyltriethoxysilane (VTES), aiming to use these polymers as precursors of ceramic matrices for the protection of carbon fibers in ceramic matrix composites (CMCs). The resulting materials exhibited better thermal stability than the carbon fiber, especially the Cfiber/SiBCO composite derived of the methyltriethoxysilane (MTES) system prepared with a B/Si ratio of 0.5. This study showed that poly(borosiloxanes) are promising materials for the oxidation protection of carbon fibers, and consequently for thermal protection systems.