Rita Salvado

Textile Materials for the Design of Wearable Antennas: A Survey

In the broad context of Wireless Body Sensor Networks for healthcare and pervasive applications, the design of wearable antennas offers the possibility of ubiquitous monitoring, communication and energy harvesting and storage. Specific requirements for wearable antennas are a planar structure and flexible construction materials. Several properties of the materials influence the behaviour of the antenna. For instance, the bandwidth and the efficiency of a planar microstrip antenna are mainly determined by the permittivity and the thickness of the substrate. The use of textiles in wearable antennas requires the characterization of their properties. Specific electrical conductive textiles are available on the market and have been successfully used. Ordinary textile fabrics have been used as substrates. However, little information can be found on the electromagnetic properties of regular textiles. Therefore this paper is mainly focused on the analysis of the dielectric properties of normal fabrics. In general, textiles present a very low dielectric constant that reduces the surface wave losses and increases the impedance bandwidth of the antenna. However, textile materials are constantly exchanging water molecules with the surroundings, which affects their electromagnetic properties. In addition, textile fabrics are porous, anisotropic and compressible materials whose thickness and density might change with low pressures. Therefore it is important to know how these characteristics influence the behaviour of the antenna in order to minimize unwanted effects. This paper presents a survey of the key points for the design and development of textile antennas, from the choice of the textile materials to the framing of the antenna. An analysis of the textile materials that have been used is also presented.

Antennas and circuits for ambient RF energy harvesting in wireless body area networks

In this paper, we identify the spectrum opportunities for radio frequency (RF) energy harvesting through power density measurements from 350 MHz to 3 GHz. The field trials have been performed in Covilhâ by using the NAKDA-SMR spectrum analyser with a measuring antenna. Based on the identification of the most promising opportunities, a dual-band band printed antenna operating at GSM bands (900/1800) is proposed, with gains of the order 1.8-2.06 dBi and efficiency 77.6-84%. Guidelines for the design of RF energy harvesting circuits and choice of textile materials for a wearable antenna are also discussed. Besides, we address the guidelines for designing circuits to harvest energy in a scenario where a wireless body area network (WBAN) is being sustained by a TX91501 Powercasf® RF dedicated transmitter and a five-stage Dickson voltage multiplier responsible for harvesting the RF energy. The IRIS motes, considered for our WBAN scenario, can perpetually operate if the RF received power attains at least -10 dBm.

Carbon Fiber Epoxy Composites for Both Strengthening and Health Monitoring of Structures

This paper presents a study of the electrical and mechanical behavior of several continuous carbon fibers epoxy composites for both strengthening and monitoring of structures. In these composites, the arrangement of fibers was deliberately diversified to test and understand the ability of the composites for self-sensing low strains. Composites with different arrangements of fibers and textile weaves, mainly unidirectional continuous carbon reinforced composites, were tested at the dynamometer. A two-probe method was considered to measure the relative electrical resistance of these composites during loading. The measured relative electrical resistance includes volume and contact electrical resistances. For all tested specimens, it increases with an increase in tensile strain, at low strain values. This is explained by the improved alignment of fibers and resulting reduction of the number of possible contacts between fibers during loading, increasing as a consequence the contact electrical resistance of the composite. Laboratory tests on strengthening of structural elements were also performed, making hand-made composites by the “wet process”, which is commonly used in civil engineering for the strengthening of all types of structures in-situ. Results show that the woven epoxy composite, used for strengthening of concrete elements is also able to sense low deformations, below 1%. Moreover, results clearly show that this textile sensor also improves the mechanical work of the strengthened structural elements, increasing their bearing capacity. Finally, the set of obtained results supports the concept of a textile fabric capable of both structural upgrade and self-monitoring of structures, especially large structures of difficult access and needing constant, sometimes very expensive, health monitoring.

Half-Mode Substrate-Integrated-Waveguide Cavity-Backed Slot Antenna on Cork Substrate

A wideband half-mode substrate-integrated-waveguide cavity-backed slot antenna covering all Unlicensed National Information Infrastructure (U-NII) radio bands (5.15-5.85 GHz) is designed, fabricated, and validated. By a half-mode implementation of a multimoded cavity with nonresonant slot, a compact ultrawideband antenna is obtained with very stable radiation characteristics, owing to the excellent antenna/platform isolation. Cork material is applied as antenna substrate, making the proposed antenna suitable for integration into floors or walls. In free-space conditions, an impedance bandwidth of 1.30 GHz (23.7%), a radiation efficiency of 85%, a front-to-back ratio of 15.0 dB, and a maximum gain of 4.3 dBi at 5.50 GHz are measured. Performance is also validated when the antenna is deployed on various dielectric or conducting platforms and underneath different dielectric superstrates. Only the latter slightly detunes the antennas impedance bandwidth. Yet, the complete frequency band of interest remains covered, owing to additional design margins incorporated in the requirements. Its compactness, unobtrusive integration potential, and stable high performance in different environments make this antenna topology an ideal candidate for Internet of Things applications.

Spectrum opportunities for electromagnetic energy harvesting from 350 mhz to 3 ghz

This paper presents spectrum opportunities for radio frequency (RF) energy harvesting identified through power density measurements from 350 MHz to 3 GHz. The field trials have been performed in two different cities (Covilha and Lisbon), by using the NARDA-SMR spectrum analyser with measuring antenna, and the Signal Hound spectrum analysers, respectively. The scope of our research considers RF energy harvesting devices, enabling to convert RF energy to direct current (DC), providing an alternative source to power supply wireless sensor network (WSN) devices. Printed antennas, able to operate at GSM (900/1800) bands, are proposed with gains of the order of 1.8-2.06 dBi and efficiency 77.6-84%. Guidelines for the choice of textile materials for a wearable antenna are also provided.

Design and evaluation of multi-band RF energy harvesting circuits and antennas for WSNs

Radio frequency (RF) energy harvesting is an emerging technology that will enable to drive the next generation of wireless sensor networks (WSNs) without the need of using batteries. In this paper, we present RF energy harvesting circuits specifically developed for GSM bands (900/1800) and a wearable dual-band antenna suitable for possible implementation within clothes for body worn applications. Besides, we address the development and experimental characterization of three different prototypes of a five-stage Dickson voltage multiplier (with match impedance circuit) responsible for harvesting the RF energy. Different printed circuit board (PCB) fabrication techniques to produce the prototypes result in different values of conversion efficiency. Therefore, we conclude that if the PCB fabrication is achieved by means of a rigorous control in the photo-positive method and chemical bath procedure applied to the PCB it allows for attaining better values for the conversion efficiency. All three prototypes (1, 2 and 3) can power supply the IRIS sensor node for RF received powers of -4 dBm, -6 dBm and -5 dBm, and conversion efficiencies of 20, 32 and 26%, respectively.

Wearable Sensors for Foetal Movement Monitoring in Low Risk Pregnancies

In low risk pregnancies, the continuous monitoring of the foetal health is based on traditional protocols for counting the foetal movements felt by the mother. Although the maternal perception is a relevant characteristic for the evaluation of the foetal health, this kind of monitoring is hard to accomplish and being subjective can induce into errors due to mother’s anxiety and lack of concentration. Furthermore, the majority of foetal fatalities occur during the last weeks of low risk pregnancies. Therefore, it is important to obtain a universal electronic obstetric tracing, allowing for the identification of sudden changes in the foetus health, by continuously monitoring the foetus movements. The Smart-Clothing project aim has been the development of easy-to-wear belts with a telemedicine system for this purpose. One of the tried solutions is the Flex sensor belt system, which guarantees real-time and continuous foetal monitoring while creating effective interfaces for querying sensor data and store all the medical record (which can later be accessed by health professionals). Another developed belt has piezoelectric sensors incorporated onto it. The piezoelectric sensor belt has shown a high capacity to detect foetal movements, isolating them from external interferences.

Smart Coat with a Fully-Embedded Textile Antenna for IoT Applications

The Internet of Things (IoT) scenario is strongly related with the advance of the development of wireless sensor networks (WSN) and radio frequency identification (RFID) systems. Additionally, in the WSN context, for a continuous feed, the integration of textile antennas for energy harvesting into smart clothing is a particularly interesting solution when the replacement of batteries is not easy to practice, such as in wearable devices. This paper presents the E-Caption: Smart and Sustainable Coat. It has an embedded dual-band textile antenna for electromagnetic energy harvesting, operating at global system for mobile communication (GSM) 900 and digital cellular system (DCS) 1800 bands. This printed antenna is fully integrated, as its dielectric is the textile material composing the coat itself. The E-Caption illustrates the innovative concept of textile antennas that can be manipulated as simple emblems. Seven prototypes of these “emblem” antennas, manufactured by lamination and embroidering techniques are also presented. It is shown that the orientation of the conductive fabric does not influence the performance of the antenna. It is also shown that the direction and number of the stitches in the embroidery may influence the performance of the antenna. Moreover, the comparison of results obtained before and after the integration of the antenna into cloth shows the integration does not affect the behavior of the antenna.

Textile antenna for electromagnetic energy harvesting for GSM900 and DCS1800 bands

Energy harvesting is the process by which energy is derived from external sources captured, and stored for small, wireless autonomous devices, like those used in wearable electronics and wireless sensor networks. This paper presents the design of two textile antenna suitable to harvest energy in the GSM900 and DCS 1800 bands. The antennas gain, are of the order 2 dBi and efficiency 80%.

Self-Monitoring Strengthening System Based on Carbon Fiber Laminate

Externally bonded composites reinforced with high-strength fibers are increasingly popular in construction, especially in structures’ strengthening, where the best possible mechanical properties are required. At the same time the ability to autodetect threats is one of the most desirable features of contemporary structures. The authors of the paper have developed an intelligent fabric, wherein the carbon fibers play the role of not only tensile reinforcement but also strain sensor. The idea is based on the construction of the strain gauge, where the thread of carbon fibers arranged in zig-zag pattern works as electrical conductor and is insulated by parallel thread of glass or acrylic fibers. Preliminary laboratory tests were designed to create effective measurement techniques and assess the effectiveness of the strengthening of selected building structures, as reinforced concrete and timber beams. Presented in the paper, selected results of these studies are very promising, although there were some noted problems to be considered in next steps. The main problem here is the control of the cross section of the fibers tow, affecting the total resistance of the fabric. One of the main deficiencies of the proposed solution is also sensitivity to moisture.