Roberto Ortiz

Mediatorless sugar/oxygen enzymatic fuel cells based on gold nanoparticle-modified electrodes.

We report on the fabrication and characterisation of a gold-nanoparticle (AuNP)-based mediatorless sugar/oxygen biofuel cell (BFC) operating in neutral sugar-containing buffers and human physiological fluids, such as blood and plasma. First, Corynascus thermophilus cellobiose dehydrogenase (CtCDH) and Myrothecium verrucaria bilirubin oxidase (MvBOx), used as anodic and cathodic bioelements, respectively, were immobilised on gold electrodes modified with 20 nm AuNPs. Detailed characterisation and optimisation of a new CDH/AuNP-based bioanode were performed and the following fundamental parameters were obtained: (i) the redox potential of the haem-containing centre of the enzyme was measured to be 75 mV vs. NHE, (ii) the surface coverage of CtCDH was found to be 0.65 pmol cm(-2) corresponding to a sub-monolayer coverage of the thiol-modified AuNPs by the enzyme, (iii) a turnover number for CtCDH immobilised on thiol-modified AuNPs was calculated to be ca. 0.5 s(-1), and (iv) the maximal current densities as high as 40 μA cm(-2) were registered in sugar-containing neutral buffers. Second, both biomodified electrodes, namely the CtCDH/AuNP-based bioanode and the MvBOx/AuNP-based biocathode, were combined into a functional BFC and the designed biodevices were carefully investigated. The following characteristics of the mediator-, separator- and membrane-less, miniature BFC were obtained: in phosphate buffer; an open-circuit voltage of 0.68 V, a maximum power density of 15 μW cm(-2) at a cell voltage of 0.52 V and in human blood; an open-circuit voltage of 0.65 V, a maximum power density of 3 μW cm(-2) at a cell voltage of 0.45 V, respectively. The estimated half-lives of the biodevices were found to be >12, <8, and <2 h in a sugar-containing buffer, human plasma, and blood, respectively. The basic characteristics of mediatorless sugar/oxygen BFCs were significantly improved compared with previously designed biodevices, because of the usage of three-dimensional AuNP-modified electrodes.

Self-powered wireless carbohydrate/oxygen sensitive biodevice based on radio signal transmission

Here for the first time, we detail self-contained (wireless and self-powered) biodevices with wireless signal transmission. Specifically, we demonstrate the operation of self-sustained carbohydrate and oxygen sensitive biodevices, consisting of a wireless electronic unit, radio transmitter and separate sensing bioelectrodes, supplied with electrical energy from a combined multi-enzyme fuel cell generating sufficient current at required voltage to power the electronics. A carbohydrate/oxygen enzymatic fuel cell was assembled by comparing the performance of a range of different bioelectrodes followed by selection of the most suitable, stable combination. Carbohydrates (viz. lactose for the demonstration) and oxygen were also chosen as bioanalytes, being important biomarkers, to demonstrate the operation of the self-contained biosensing device, employing enzyme-modified bioelectrodes to enable the actual sensing. A wireless electronic unit, consisting of a micropotentiostat, an energy harvesting module (voltage amplifier together with a capacitor), and a radio microchip, were designed to enable the biofuel cell to be used as a power supply for managing the sensing devices and for wireless data transmission. The electronic system used required current and voltages greater than 44 µA and 0.57 V, respectively to operate; which the biofuel cell was capable of providing, when placed in a carbohydrate and oxygen containing buffer. In addition, a USB based receiver and computer software were employed for proof-of concept tests of the developed biodevices. Operation of bench-top prototypes was demonstrated in buffers containing different concentrations of the analytes, showcasing that the variation in response of both carbohydrate and oxygen biosensors could be monitored wirelessly in real-time as analyte concentrations in buffers were changed, using only an enzymatic fuel cell as a power supply.

Cellobiose dehydrogenase modified electrodes: advances by materials science and biochemical engineering

The flavocytochrome cellobiose dehydrogenase (CDH) is a versatile biorecognition element capable of detecting carbohydrates as well as quinones and catecholamines. In addition, it can be used as an anode biocatalyst for enzymatic biofuel cells to power miniaturised sensor–transmitter systems. Various electrode materials and designs have been tested in the past decade to utilize and enhance the direct electron transfer (DET) from the enzyme to the electrode. Additionally, mediated electron transfer (MET) approaches via soluble redox mediators and redox polymers have been pursued. Biosensors for cellobiose, lactose and glucose determination are based on CDH from different fungal producers, which show differences with respect to substrate specificity, pH optima, DET efficiency and surface binding affinity. Biosensors for the detection of quinones and catecholamines can use carbohydrates for analyte regeneration and signal amplification. This review discusses different approaches to enhance the sensitivity and selectivity of CDH-based biosensors, which focus on (1) more efficient DET on chemically modified or nanostructured electrodes, (2) the synthesis of custom-made redox polymers for higher MET currents and (3) the engineering of enzymes and reaction pathways. Combination of these strategies will enable the design of sensitive and selective CDH-based biosensors with reduced electrode size for the detection of analytes in continuous on-site and point-of-care applications.

Direct Electrochemistry of Phanerochaete chrysosporium Cellobiose Dehydrogenase Covalently Attached onto Gold Nanoparticle Modified Solid Gold Electrodes.

Achieving efficient electrochemical communication between redox enzymes and various electrode materials is one of the main challenges in bioelectrochemistry and is of great importance for developing electronic applications. Cellobiose dehydrogenase (CDH) is an extracellular flavocytochrome composed of a catalytic FAD containing dehydrogenase domain (DH(CDH)), a heme b containing cytochrome domain (CYT(CDH)), and a flexible linker region connecting the two domains. Efficient direct electron transfer (DET) of CDH from the basidiomycete Phanerochaete chrysosporium (PcCDH) covalently attached to mixed self-assembled monolayer (SAM) modified gold nanoparticle (AuNP) electrode is presented. The thiols used were as follows: 4-aminothiophenol (4-ATP), 4-mercaptobenzoic acid (4-MBA), 4-mercaptophenol (4-MP), 11-mercapto-1-undecanamine (MUNH(2)), 11-mercapto-1-undecanoic acid (MUCOOH), and 11-mercapto-1-undecanol (MUOH). A covalent linkage between PcCDH and 4-ATP or MUNH(2) in the mixed SAMs was formed using glutaraldehyde as cross-linker. The covalent immobilization and the surface coverage of PcCDH were confirmed with surface plasmon resonance (SPR). To improve current density, AuNPs were cast on the top of polycrystalline gold electrodes. For all the immobilized PcCDH modified AuNPs electrodes, cyclic voltammetry exhibited clear electrochemical responses of the CYT(CDH) with fast electron transfer (ET) rates in the absence of substrate (lactose), and the formal potential was evaluated to be +162 mV vs NHE at pH 4.50. The standard ET rate constant (k(s)) was estimated for the first time for CDH and was found to be 52.1, 59.8, 112, and 154 s(-1) for 4-ATP/4-MBA, 4-ATP/4-MP, MUNH(2)/MUCOOH, and MUNH(2)/MUOH modified electrodes, respectively. At all the mixed SAM modified AuNP electrodes, PcCDH showed DET only via the CYT(CDH). No DET communication between the DH(CDH) domain and the electrode was found. The current density for lactose oxidation was remarkably increased by introduction of the AuNPs. The 4-ATP/4-MBA modified AuNPs exhibited a current density up to 30 μA cm(-2), which is ∼70 times higher than that obtained for a 4-ATP/4-MBA modified polycrystalline gold electrode. The results provide insight into fundamental electrochemical properties of CDH covalently immobilized on gold electrodes and promote further applications of CDHs for biosensors, biofuel cells, and bioelectrocatalysis.

Effect of Deglycosylation of Cellobiose Dehydrogenases on the Enhancement of Direct Electron Transfer with Electrodes

Cellobiose dehydrogenase (CDH) is a monomeric extracellular flavocytochrome composed of a catalytic dehydrogenase domain (DH(CDH)) containing flavin adenine dinucleotide (FAD), a cytochrome domain (CYT(CDH)) containing heme b, and a linker region connecting the two domains. In this work, the effect of deglycosylation on the electrochemical properties of CDH from Phanerochaete chrysosporium (PcCDH) and Ceriporiopsis subvermispora (CsCDH) is presented. All the glycosylated and deglycosylated enzymes show direct electron transfer (DET) between the CYT(CDH) and the electrode. Graphite electrodes modified with deglycosylated PcCDH (dPcCDH) and CsCDH (dCsCDH) have a 40-65% higher I(max) value in the presence of substrate than electrodes modified with their glycosylated counterparts. CsCDH trapped under a permselective membrane showed similar changes on gold electrodes protected by a thiol-based self-assembled monolayer (SAM), in contrast to PcCDH for which deglycosylation did not exhibit any different electrocatalytical response on SAM-modified gold electrodes. Glycosylated PcCDH was found to have a 30% bigger hydrodynamic radius than dPcCDH using dynamic light scattering. The basic bioelectrochemistry as well as the bioelectrocatalytic properties are presented.

Label free capacitive immunosensor for detecting calpastatin — A meat tenderness biomarker

An immunological capacitive biosensor for calpastatin was developed, optimized and applied for the analysis of meat extract samples. Anti-calpastatin antibody was immobilized on a gold electrode modified with a self-assembled monolayer of mercaptoundecanoic acid and Protein A from Staphylococcus aureus, and the obtained immunosensor was inserted as the working electrode in an electrochemical cell of a flow injection system. The dynamic range of the sensor was 20 to 160 ng/mL calpastatin. The electrode could be regenerated and re-used for more than 7 days with minimal reduction in sensitivity. For the analysis of real samples, the target analyte was extracted from the Longissimus dorsi muscle from beef carcasses directly after slaughtering. The extract was analyzed both with the developed immunosensor and microtiter plate ELISA, and a good correlation was obtained. However the immunosensor offers advantages of speed, simplicity, sensitivity and possibility for miniaturization over conventional assays for calpastatin quantification.

Graphite electrodes modified with Neurospora crassa cellobiose dehydrogenase: Comparative electrochemical characterization under direct and mediated electron transfer

The electrochemical characterization of a class II cellobiose dehydrogenase (CDH), from the ascomycete fungus Neurospora crassa, adsorbed on graphite (G), was performed in regard to direct (DET) and mediated electron transfer (MET). The effects of the applied potential, mediator (1,4 benzoquinone) concentration and flow carrier pH on the amperometric response of the G/CDH modified electrodes were investigated under flow conditions. From the calibration curves, recorded at two pH values (5.2 and 7.0) for nine different sugars, the kinetic and the analytical parameters were evaluated under DET and MET operation modes. These results together with those obtained from long term operational stability measurements showed that: (i) for all nine investigated sugars the sensitivity was higher for MET than for DET and for pH 5.2 compared to pH 7.0; (ii) irrespective of DET or MET operation mode, the sensitivity of the new enzyme towards the investigated sugars decreased in the following sequence: cellobiose>lactose>(cellotriose≈cellopentaose) >>(maltotriose≈maltotetraose≈maltopentaose)>(maltose≈glucose); (iii) for all tested substrates, the apparent CDH affinity was roughly higher in DET than in MET operation mode.

Direct electron transfer of Phanerochaete chrysosporium cellobiose dehydrogenase at platinum and palladium nanoparticles decorated carbon nanotubes modified electrodes

In the present work, platinum and palladium nanoparticles (PtNPs and PdNPs) were decorated on the surface of multi-walled carbon nanotubes (MWCNTs) by a simple thermal decomposition method. The prepared nanohybrids, PtNPs-MWCNTs and PdNPs-MWCNTs, were cast on the surface of spectrographic graphite electrodes and then Phanerochaete chrysosporium cellobiose dehydrogenase (PcCDH) was adsorbed on the modified layer. Direct electron transfer between PcCDH and the nanostructured modified electrodes was studied using flow injection amperometry and cyclic voltammetry. The maximum current responses (Imax) and the apparent Michaelis-Menten constants (K) for the different PcCDH modified electrodes were calculated by fitting the data to the Michaelis-Menten equation and compared. The sensitivity towards lactose was 3.07 and 3.28 μA mM(-1) at the PcCDH/PtNPs-MWCNTs/SPGE and PcCDH/PdNPs-MWCNTs/SPGE electrodes, respectively, which were higher than those measured at the PcCDH/MWCNTs/SPGE (2.60 μA mM(-1)) and PcCDH/SPGE (0.92 μA mM(-1)). The modified electrodes were additionally tested as bioanodes for biofuel cell applications.

Indirect, non-competitive amperometric immunoassay for accurate quantification of calpastatin, a meat tenderness marker, in bovine muscle

A method is described for quantification of the beef tenderness marker, calpastatin, in meat samples by amperometric detection. Using a novel bovine recombinant partial calpastatin protein as standard antigen a low detection limit of 0.2 ng/mL was achieved. The influence of the complex matrix was minimised by heat pretreatment and dilution of the samples prior to detection of calpastatin. The relative error between the direct sample measurement and standard addition methods was 5.89%, confirming the accuracy of the developed amperometric immunoassay.

Salt-Induced Control of the Grafting Density in Poly(ethylene glycol) Brush Layers by a Grafting-to Approach

In this work, a method to obtain control of the grafting density during the formation of polymer brush layers by the grafting-to method of thiolated poly(ethylene glycol) onto gold is presented. The grafting density of the polymer chains was adjusted by adding Na2SO4 in concentrations between 0.2 and 0.9 M to the aqueous polymer solution during the grafting process. The obtained grafting densities ranged from 0.26 to 1.60 chains nm-2, as determined by surface plasmon resonance. The kinetics of the grafting process were studied in situ by a quartz crystal microbalance with dissipation, and a mushroom to brush conformational transition was observed when the polymer was grafted in the presence of Na2SO4. The transition from mushroom to brush was only observed for long periods of grafting, highlighting the importance of time to obtain high grafting densities. Finally, the prepared brush layer with the highest grafting density showed high resistance to the adsorption of bovine serum albumin, while layers with a lower grafting density showed only limited resistance.