Rogier Besselink

Improved Langmuir−Blodgett titanate films via in situ exfoliation study and optimization of deposition parameters

The exfoliation and deposition of large (10-100 μm) Ti0.87O2 and small (0.1-1 μm) Ti0.91O2 nanosheets from lepidocrocite-type protonated titanates was investigated for getting high quality films. Exfoliation was carried out with different tetra-alkyl ammonium ions (TAA(+)) and varying TAA(+)/H(+) ratios, and the colloidal solutions were characterized by small-angle X-ray scattering (SAXS) and ultraviolet-visible (UV-vis) spectroscopy. Using Langmuir-Blodgett deposition the titanate nanosheets were directly transferred onto a Si substrate. The resulting films were characterized by atomic force microscopy (AFM).The results indicate that the H1.07Ti1.73O4 titanate exfoliated at very low ratios of TAA(+)/H(+); no lower threshold for exfoliation was observed for the TAA(+) concentration. Nanosheets exfoliated at very low ratios of TAA(+)/H(+) typically showed a small size and porous surface. Subsequent exfoliation of the remaining layered titanate particles yielded much higher quality nanosheets. The optimized deposition parameters for Langmuir-Blodgett films suggest that the surface pressure is a key parameter to control the coverage of the film. The bulk concentration of nanosheets was found to be a less important deposition parameter in the LB deposition process. It only influenced whether the desired surface pressure could be reached at a given maximum degree of compression.

Formation of calcium sulfate through the aggregation of sub-3 nanometre primary species

The formation pathways of gypsum remain uncertain. Here, using truly in situ and fast time-resolved small-angle X-ray scattering, we quantify the four-stage solution-based nucleation and growth of gypsum (CaSO4·2H2O), an important mineral phase on Earth and Mars. The reaction starts through the fast formation of well-defined, primary species of <3 nm in length (stage I), followed in stage II by their arrangement into domains. The variations in volume fractions and electron densities suggest that these fast forming primary species contain Ca–SO4-cores that self-assemble in stage III into large aggregates. Within the aggregates these well-defined primary species start to grow (stage IV), and fully crystalize into gypsum through a structural rearrangement. Our results allow for a quantitative understanding of how natural calcium sulfate deposits may form on Earth and how a terrestrially unstable phase-like bassanite can persist at low-water activities currently dominating the surface of Mars.

The swelling transition of lepidocrocite-type protonated layered titanates into anatase under hydrothermal treatment

The common facets of anatase crystals are the (001) and (101) planes. However, the phase transformation from lepidocrocite-type titanate into anatase by hydrothermal processing yields an anatase microstructure with high concentration of exposed (010) planes. The phase transformation of a lepidocrocite-type protonated layered titanate (HTO) into anatase was studied using XRD, TEM, FTIR, and measurement of pH and zeta potential. It was found that HTO is proton-deficient. The phase transformation process begins after uptake of a sufficient number of protons into the lepidocrocite-type structure. With the uptake of protons new hydroxyl groups form on the internal surfaces of the layered titanate and result in a bilayer state of HTO. The phase transformation reaction is a topotactic dehydration reaction in which anatase forms and water is expelled by syneresis.

The Rapid Exfoliation and Subsequent Restacking of Layered Titanates Driven by an Acid–Base Reaction†

Two-dimensional (2D) (hydro)oxide materials, that is, nanosheets, enable the preparation of advanced 2D materials and devices. The general synthesis route of nanosheets involves exfoliating layered metal (hydro)oxide crystals. This exfoliation process is considered to be time-consuming, hindering their industrial-scale production. Based on in situ exfoliation studies on the protonated layered titanate H(1.07)Ti(1.73)O4⋅H2O (HTO), it is now shown that ion intercalation-assisted exfoliation driven by chemical reaction provides a viable and fast route to isolated nanosheets. Contrary to the general expectation, data indicate that direct exfoliation of HTO occurs within seconds after mixing of the reactants, instead of proceeding via a swollen state as previously thought. These findings reveal that ion intercalation-assisted exfoliation driven by chemical reaction is a promising exfoliation route for large-scale synthesis.

Time-resolved Small Angle X-ray Scattering Study of Sol-Gel Precursor Solutions of Lead Zirconate Titanate and Zirconia

The evolution of nanostructure in sol-gel derived lead zirconate titanate (PZT) and zirconia precursor sols at different hydrolysis ratios was investigated by small angle X-ray scattering (SAXS). The shape of the clusters in the zirconia sol could be described by the length-polydisperse cylindrical form factor. The zirconia-based clusters were characterized by a cross-sectional radius, r(0), of 0.28 nm and a practically monodisperse length of ca. 1.85 nm. These clusters were probably constructed of zirconia-related tetrameric building blocks. Similar cylindrical structural motifs were observed in PZT precursor sols with [H(2)O]/[Zr+Ti]=9.26 and 27.6, but the polydispersity in length was much higher. Clear scattering contributions from Ti and Pb centers were not detected, which was interpreted in terms of a homogeneous distribution of unbound lead ions in solution and the relatively low scattering intensity from any Ti-based clusters or oligomers that may have been present in the sols.

Evolution of microstructure in mixed niobia-hybrid silica thin films from sol–gel precursors

The evolution of structure in sol-gel derived mixed bridged silsesquioxane-niobium alkoxide sols and drying thin films was monitored in situ by small-angle X-ray scattering. Since sol-gel condensation of metal alkoxides proceeds much faster than that of silicon alkoxides, the incorporation of d-block metal dopants into silica typically leads to formation of densely packed nano-sized metal oxide clusters that we refer as metal oxide building blocks in a silica-based matrix. SAXS was used to study the process of niobia building block formation while drying the sol as a thin film at 40-80°C. The SAXS curves of mixed niobia-hybrid silica sols were dominated by the electron density contrast between sol particles and surrounding solvent. As the solvent evaporated and the sol particles approached each other, a correlation peak emerged. Since TEM microscopy revealed the absence of mesopores, the correlation peak was caused by a heterogeneous system of electron-rich regions and electron poor regions. The regions were assigned to small clusters that are rich in niobium and which are dispersed in a matrix that mainly consisted of hybrid silica. The correlation peak was associated with the typical distances between the electron dense clusters and corresponded with distances in real space of 1-3 nm. A relationship between the prehydrolysis time of the silica precursor and the size of the niobia building blocks was observed. When 1,2-bis(triethoxysilyl)ethane was first hydrolyzed for 30 min before adding niobium penta-ethoxide, the niobia building blocks reached a radius of 0.4 nm. Simultaneous hydrolysis of the two precursors resulted in somewhat larger average building block radii of 0.5-0.6 nm. This study shows that acid-catalyzed sol-gel polymerization of mixed hybrid silica niobium alkoxides can be rationalized and optimized by monitoring the structural evolution using time-resolved SAXS.

Doped microporous hybrid silica membranes for gas separation

Hybrid silica (i.e., bis-triethoxysilylethane: BTESE) membranes doped with B, Ta or Nb were made through a sol–gel process. Triethyl borate, tantalum (V) ethoxide (TPE) and niobium (V) ethoxide (NPE) were selected as doping precursors. The doping concentration was optimized to produce sols, suitable for membrane fabrication. Thermal stability, structural analysis, cross-sectional micrographs and single gas permeation experiments were performed on these membranes, and results are compared with an undoped BTESE membrane. It was observed that the synthesized doped BTESE materials and membranes resulted into a more open (and, in one occurrence, SF6 permeable) pore microstructure, showing high permeances of larger gas molecules, while having a cross-sectional thickness comparable to undoped BTESE membranes.Graphical Abstract

Mass-fractal growth in niobia/silsesquioxane mixtures: a small-angle X-ray scattering study

The nucleation and growth of niobium pentaethoxide-derived clusters in ethanol was monitored at 298–333 K by small-angle X-ray scattering. The data were analyzed with a newly derived model for polydisperse mass-fractal-like structures.

Following the Kinetics of Barium Titanate Nanocrystal Formation in Benzyl Alcohol Under Near-Ambient Conditions

In complex chemical syntheses (e.g., coprecipitation reactions), nucleation, growth, and coarsening often occur concurrently, obscuring the individual processes. Improved knowledge of these processes will help to better understand and optimize the reaction protocol. Here, a form-free and model independent approach, based on a combination of time-resolved small/wide-angle X-ray scattering, is employed to elucidate the effect of reaction parameters (such as precursor concentration, reactant stoichiometry, and temperature) on the nucleation, crystallization, and growth phenomena during the formation of nanocrystalline barium titanate. The strength of this approach is that it relies solely on the total scattered intensity (i.e., scattering invariant) of the investigated system, and no prior knowledge is required. As such, it can be widely applied to other synthesis protocols and materials systems. Through the scattering invariant, it is found that the amorphous-to-crystalline transformation of barium titanate is predominantly determined by the total amount of water released from the gel-like barium hydroxide octahydrate precursor, and three rate-limiting regimes are established. As a result of this improved understanding of the effect of varying reaction conditions, elementary boundary conditions can be set up for a better control of the barium titanate nanocrystal synthesis.