Ronen Gottesman

Extremely Slow Photoconductivity Response of CH3NH3PbI3 Perovskites Suggesting Structural Changes under Working Conditions

Photoconductivity measurements of CH3NH3PbI3 deposited between two dielectric-protected Au electrodes show extremely slow response. The CH3NH3PbI3, bridging a gap of ∼2000 nm, was subjected to a DC bias and cycles of 5 min illumination and varying dark duration. The approach to steady -state photocurrent lasted tens of seconds with a strong dependence on the dark duration preceding the illumination. On the basis of DFT calculations, we propose that under light + bias the methylammonium ions are freed to rotate and align along the electric field, thus modifying the structure of the inorganic scaffold. While ions alignment is expected to be fast, the adjustment of the inorganic scaffold seems to last seconds as reflected in the extremely slow photoconductivity response. We propose that under working conditions a modified, photostable, perovskite structure is formed, depending on the bias and illumination parameters. Our findings seem to clarify the origin of the well-known hysteresis in perovskite solar cells.

Photoinduced Reversible Structural Transformations in Free-Standing CH3NH3PbI3 Perovskite Films

In the pursuit to better understand the mechanisms of perovskite solar cells we performed Raman and photoluminescence measurements of free-standing CH3NH3PbI3 films, comparing dark with working conditions. The films, grown on a glass substrate and sealed by a thin glass coverslip, were measured subsequent to dark and white-light pretreatments. The extremely slow changes we observe in both the Raman and photoluminescence cannot be regarded as electronic processes, which are much faster. Thus, the most probable explanation is of slow photoinduced structural changes. The CH3NH3PbI3 transformation between the dark and the light structures is reversible, with faster rates for the changes under illumination. The results seem to clarify several common observations associated with solar cell mechanisms, like performance improvement under light soaking. More important is the call for solar-cell-related investigation of CH3NH3PbI3 to take the photoinduced structural changes into consideration when measuring and interpreting the results.

Open circuit potential build-up in perovskite solar cells from dark conditions to 1 sun.

The high open-circuit potential (Voc) achieved by perovskite solar cells (PSCs) is one of the keys to their success. The Voc analysis is essential to understand their working mechanisms. A large number of CH3NH3PbI3-xClx PSCs were fabricated on single large-area substrates and their Voc dependencies on illumination intensity, I0, were measured showing three distinctive regions. Similar results obtained in Al2O3 based PSCs relate the effect to the compact TiO2 rather than the mesoporous oxide. We propose that two working mechanisms control the Voc in PSCs. The rise of Voc at low I0 is determined by the employed semiconductor n-type contact (TiO2 or MgO coated TiO2). In contrast, at I0 close to AM1.5G, the employed oxide does not affect the achieved voltage. Thus, a change of regime from an oxide-dominated EFn (as in the dye sensitized solar cells) to an EFn, directly determined by the CH3NH3PbI3-xClx absorber is suggested.

Cs+ incorporation into CH3NH3PbI3 perovskite: substitution limit and stability enhancement

In this study we systematically explored the mixed cation perovskite Csx(CH3NH3)1−xPbI3. We exchanged the A-site cation by dipping MAPbI3 films into a CsI solution, thereby incrementally replacing the MA+ in a time-resolved dipping process and analysed the resulting thin-films with UV-Vis, XRD, EDAX, SEM and optical depth-analysis in a high-throughput fashion. Additional in situ UV-Vis and time-resolved XRD measurements allowed us to look at the kinetics of the formation process. The results showed a discontinuity during the conversion. Firstly, small amounts of Cs+ are incorporated into the structure. After a few minutes, the Cs content approaches a limit and grains of δ-CsPbI3 occur, indicating a substitution limit. We compared this cation exchange to a one-step crystallisation approach and found the same effect of phase segregation, which shows that the substitution limit is an intrinsic feature rather than a kinetic effect. Optical and structural properties changed continuously for small Cs incorporations. Larger amounts of Cs result in phase segregation. We estimate the substitution limit of CsxMA1−xPbI3 to start at a Cs ratio x = 0.13, based on combined measurements of EDAX, UV-Vis and XRD. The photovoltaic performance of the mixed cation perovskite shows a large increase in device stability from days to weeks. The initial efficiency of mixed CsxMA1−xPbI3 devices decreases slightly, which is compensated by stability after a few days.

Relaxation of Electron Carriers in the Density of States of Nanocrystalline TiO2

Band gap localized states and surface states play a dominant role in the application of nanocrystalline metal oxides to photovoltaics and solar fuel production. Electrons injected in nanocrystalline TiO2 by voltage or photogeneration are mainly located in band gap states. Therefore, charging a nanoparticulate semiconductor network allows one to recover the density of states (DOS) in the energy axis. However, shallow traps remain in equilibrium with the conduction band electrons, while deep traps do not. We show that the characteristic peak of the apparent DOS mixes an exponential DOS and a monoenergetic surface state. A model that incorporates the traps kinetics proves to be very efficient to assess the important parameters that determine both contributions via variation of charging rate. Contrary to the common theory, we demonstrate that the peculiar capacitance peak of nanocrystalline TiO2 can be mainly attributed, in some cases, to deep traps in the exponential distribution.

Silver nanowires and nanoparticles from a millifluidic reactor: application to metal assisted silicon etching

Silver nanowires and nanoparticles are synthesized by a polyol method in a millifluidic reactor. We have been able to optimize the flow chemistry reaction conditions to get a high yield of nanowires in a continuous flow. By changing reaction parameters we have demonstrated the synthesis of single crystalline silver nanoparticles in a rapid reaction time of only 3 minutes. All results are compared with standard batch and microwave reactions. An example of application is provided through the silver nanowire assisted etching of silicon wafers. This colloidal approach of metal assisted silicon etching allows transferring of the nanowire shape to silicon.