Rong Situ

Particle emissions, volatility, and toxicity from an ethanol fumigated compression ignition engine.

Particle emissions, volatility, and the concentration of reactive oxygen species (ROS) were investigated for a pre-Euro I compression ignition engine to study the potential health impacts of employing ethanol fumigation technology. Engine testing was performed in two separate experimental campaigns with most testing performed at intermediate speed with four different load settings and various ethanol substitutions. A scanning mobility particle sizer (SMPS) was used to determine particle size distributions, a volatilization tandem differential mobility analyzer (V-TDMA) was used to explore particle volatility, and a new profluorescent nitroxide probe, BPEAnit, was used to investigate the potential toxicity of particles. The greatest particulate mass reduction was achieved with ethanol fumigation at full load, which contributed to the formation of a nucleation mode. Ethanol fumigation increased the volatility of particles by coating the particles with organic material or by making extra organic material available as an external mixture. In addition, the particle-related ROS concentrations increased with ethanol fumigation and were associated with the formation of a nucleation mode. The smaller particles, the increased volatility, and the increase in potential particle toxicity with ethanol fumigation may provide a substantial barrier for the uptake of fumigation technology using ethanol as a supplementary fuel.

Local flow measurements of vertical upward bubbly flow in an annulus

Local measurements of flow parameters were performed for vertical upward bubbly flows in an annulus. The annulus channel consisted of an inner rod with a diameter of 19.1 mm and an outer round tube with an inner diameter of 38.1 mm, and the hydraulic equivalent diameter was 19.1 mm. Double-sensor conductivity probe was used for measuring void fraction, interfacial area concentration, and interfacial velocity, and Laser Doppler anemometer was utilized for measuring liquid velocity and turbulence intensity. A total of 20 data sets for void fraction, interfacial area concentration, and interfacial velocity were acquired consisting of five void fractions, about 0.050, 0.10, 0.15, 0.20, and 0.25, and four superficial liquid velocities, 0.272, 0.516, 1.03, and 2.08 m/s. A total of 8 data sets for liquid velocity and turbulence intensity were acquired consisting of five void fractions, about 0.050, and 0.10, and four superficial liquid velocities, 0.272, 0.516, 1.03, and 2.08 m/s. The constitutive equations for distribution parameter and drift velocity in the drift-flux model, and the semi-theoretical correlation for Sauter mean diameter namely interfacial area concentration, which were proposed previously, were validated by local flow parameters obtained in the experiment using the annulus.

Interfacial area transport of vertical upward bubbly two-phase flow in an annulus

In relation to the development of the interfacial area transport equation in a subcooled boiling flow, the one-dimensional interfacial area transport equation was evaluated by the data taken in the hydrodynamic separate effect tests without phase change for an adiabatic air-water bubbly flow in a vertical annulus. The annulus channel consisted of an inner rod with a diameter of 19.1 mm and an outer round tube with an inner diameter of 38.1 mm, and the hydraulic equivalent diameter was 19.1 mm. Twenty data sets consisting of five void fractions, about 0.050, 0.10, 0.15, 0.20, and 0.25, and four superficial liquid velocities, 0.272, 0.516, 1.03, and 2.08 m/s were used for the evaluation of the one-dimensional interfacial area transport equation. The one-dimensional interfacial area transport equation agreed with the data with an average relative deviation of ±8.96 %. Sensitivity analysis was also performed to investigate the effect of the initial bubble size on the interfacial area transport. It was shown that the dominant mechanism of the interfacial area transport was strongly dependent of the initial bubble size.

Experimental study on interfacial area transport in vertical upward bubbly two-phase flow in an annulus

Forced convection subcooled water boiling experiments were conducted in a vertical annular channel. A high-speed digital video camera was applied to record the dynamics of the subcooled boiling process. The flow visualization results show that the bubble departure frequency generally increases as the heat flux increases. For some cases, the departure frequency may reach a limit around 1000 bubbles/second. In addition, bubble lift-off diameter, bubble growth rate and bubble velocity after bubble lift-off were determined by analyzing the images. The experimental data obtained from this study can be used in modeling the bubble departure frequency, bubble lift-off diameter, and bubble dynamics in forced convection subcooled boiling.

Mixing and dispersion of pollutants emitted from an outboard motor.

This paper quantifies the mixing and dispersion from an outboard motor by field experiments in a small subtropical waterway. Organic dye was used as a surrogate for exhaust emissions and was mixed with uncontaminated creek water before being dispersed into the creek. Dye concentrations were measured with an array of concentration probes stationed in the creek. The data were then processed and fitted with a power law function. The corresponding dispersion constants agreed well with the literature. However, the amplitude was lower than the IMO equation but higher than the correlation from laboratory tests. Results for dye concentration intermittency (presence of dye) are presented for the first time from such field measurements and show significant mixing in-homogeneity.

Erratum to “Modeling of bubble-layer thickness for formulation of one-dimensional interfacial area transport equation in subcooled boiling two-phase flow” [International Journal of Heat and Mass Transfer 46 (2003) 1409–1423]

[Extract] The publishers regret that the following corrections were omitted in the published version.

Bubble Lift-Off Size in Forced Convection Subcooled Boiling

Forced convection subcooled boiling experiments were conducted in a BWR-scaled vertical upward annular channel. Water was used as the testing fluid, and the tests were performed at atmospheric pressure. A high-speed digital video camera was applied to capture the dynamics of the bubble nucleation process. Bubble lift-off diameters were obtained from the images for a total of 91 test conditions. A force balance analysis of a growing bubble was carried out. A constitutive relation for bubble lift-off size was obtained by correlating current water data and R113 data from literature. The proposed constitutive relation and experimental data agree well with each other.