Rubo Xing

Preparation, patterning and luminescent properties of nanocrystalline Gd2O3 : A (A = Eu3+, Dy3+, Sm3+, Er3+) phosphor films via Pechini sol-gel soft lithography

Nanocrystalline Gd2O3:A (A = Eu3+, Dy3+, Sm3+, Er3+) phosphor films and their patterning were fabricated by a Pechini sol-gel process combined with a soft lithography. X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and optical microscopy, UV/vis transmission and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 500 degreesC and that the crystallinity increased with the elevation of annealing temperatures. Uniform and crack free non-patterned phosphor films were obtained by optimizing the composition of the coating sol, which mainly consisted of grains with an average size of 70 nm and a thickness of 550 nm. Using micro-molding in capillaries technique, we obtained homogeneous and defects-free patterned gel and crystalline phosphor films with different stripe widths (5, 10, 20 and 50 mum). Significant shrinkage (50%) was observed in the patterned films during the heat treatment process. The doped rare earth ions (A) showed their characteristic emission in crystalline Gd2O3 phosphor films due to an efficient energy transfer from Gd2O3 host to them. Both the lifetimes and PL intensity of the rare earth ions increased with increasing the annealing temperature from 500 to 900 degreesC, and the optimum concentrations for Eu3+, Dy3+, sm(3+), Er3+ were determined to be 5, 0.25, 1 and 1.5 mol% of Gd3+ in Gd2O3 films, respectively.

Patterning and luminescent properties of nanocrystalline Y2O3:Eu3+ phosphor films by sol–gel soft lithography

Nanocrystalline Y2O3:Eu3+ phosphor films and their patterning were fabricated by a Pechini sol-gel process combined with a soft lithography. X-ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG-DTA), atomic force microscopy (AFM), optical microscopy, UV/vis transmission and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 500 degreesC and the crystallinity increased with the elevation of annealing temperatures. Uniform and crack free non-patterned phosphor films were obtained, which mainly consisted of grains with an average size of 70 nm. Using micro-molding in capillaries technique, we obtained homogeneous and defects-free patterned gel and crystalline phosphor films with different stripe widths (5, 10, 20 and 50 mum). Significant shrinkage (50%) was observed in the patterned films during the heat treatment process. The doped Eu3+ showed its characteristic emission in crystalline Y2O3 phosphor films due to an efficient energy transfer from Y2O3 host to them. Both the lifetimes and PL intensity of the Eu3+ increased with increasing the annealing temperature from 500 to 900 degreesC, and the optimum concentrations for Eu3+ were determined to be 5 mol%.

Oriented Poly(3-hexylthiophene) Nanofibril with the π−π Stacking Growth Direction by Solvent Directional Evaporation

In this article, the uniaxial alignment of poly(3-hexylthiophene) (P3HT) nanofibrils with a π-π stacking growth direction in which P3HT chains adopt a flat-on conformation was obtained by solvent directional evaporation using a glass cover slide and a poly(dimethylsiloxane) (PDMS) sheet to press the P3HT film in a carbon disulfide (CS(2)) atmosphere. By controlling the CS(2) vapor pressure during the film-forming process, we got a well-oriented P3HT film whose order parameter reached as high as 0.97. The orientation of the film was induced by the crystallization nucleation of P3HT and the directional evaporation of the solvent. Under a CS(2) vapor atmosphere, P3HT crystals preferred to adopt the form II modification, which started by nucleation. Owing to the solvent directional evaporation from the center to the margin, P3HT at the center of the sample would precipitate first to induce nucleation. Then the peripheral P3HT would directly diffuse, precipitate, and then adhere to the nucleus to form the uniaxial alignment of P3HT nanofibrils along the direction of solvent evaporation. Furthermore, in the P3HT nanofibrils, the π-π stacking direction of P3HT lamellae was parallel to the crystal growth direction, which would provide an effective path for charge transport.

Patterning thin polymer films by surface-directed dewetting and pattern transfer

The pattern evolution processes of thin polystyrene (PS) film on chemically patterned substrates during dewetting have been investigated experimentally. The substrates have patterns of self-assembly monolayers produced by microcontact printing with octadecyltrichlorosilane. Optical microscopy and atomic force microscopy images reveal that ordered micrometer scale pattern can be created by surface direct dewetting. Various pattern sizes and pattern complexities can be achieved by controlling the experimental parameters. The dewetting pattern has been transferred to form PDMS stamp for soft lithography.

Detection of explosives with porous xerogel film from conjugated carbazole-based dendrimers

The carbazole-based conjugated dendrimer H2-BCz with tert-butyl surface groups shows selective gelation behavior in a good solvent and anti-solvent mixture. The sol–gel conversion of H2-BCz can be observed on heating and cooling. The H2-BCz xerogel films show three-dimensional porous networks with the nanofibers (layered structures with a period of 1.38 nm) entangling and intersecting with each other. The π–π interactions between the aryl units may be the driving force for the formation of one-dimensional H2-BCz fibers during the gelation process. Due to the electron-donating property of the H2-BCz molecule and the porosity of the fibrous film, the xerogel films can be used as efficient fluorescence quenching based chemsensors for the detection of nitroaromatic explosives, such as 2,4,6-trinitrotoluene (TNT) and 2,4-dinitrotoluene (DNT). The quenching efficiency was as high as 77% and 91% when exposed to the vapor of TNT and DNT, respectively.

Ordered droplet formation by thin polymer film dewetting on a stripe-patterned substrate

The dewetting process of thin polystyrene (PS) film on flat and stripe-patterned substrates is presented. Different dewetting processes were observed when the thin PS films annealed at above the glass transition temperature on these different kinds of substrates. The final dewetting on the flat substrate led to formation of polygonal liquid droplets, while on the stripe-patterned substrate, the droplets were observed to align at the centers of the stripes. A possible explanation for the dewetting process on the stripe-patterned substrate is proposed.

How to form regular polymer microstructures by surface-pattern-directed dewetting

The substrates with regular patterns of self-assembly monolayers (SAMs) produced by microcontact printing with octadecyltrichlorosilane (OTS) was employed to direct thin polystyrene dewetting to fabricate ordered micrometer scale pattern. The pattern sizes and pattern fashion can be manipulated by controlling the experimental parameters. The pattern formation mechanisms have been discussed. The dewetting pattern can be transferred to form PDMS stamp for future microfabrication process.

Patterning and photoluminescent properties of perovskite-type organic/inorganic hybrid luminescent films by soft lithography

Perovskite-type organic/inorganic hybrid layered compound (C6H5C2H4NH3)(2)PbI4 was synthesized. The patterning Of (C6H5C2H4NH3)(2)PbI4 thin films on silicon substrate was realized by the micromolding in capillaries (MIMIC) process, a kind of soft lithography. Bright green luminescent stripes with different widths (50, 15, 0.8 mum) have been obtained. The structure and optical properties Of (C6H5C2H4NH3)(2)PbI4 films were characterized by X-ray diffraction (XRD), UV/Vis absorption and photoluminescence excitation and emission spectra, respectively. It is shown that the organic-inorganic layered (C6H5C2H4NH3)(2)PbI4 film was c-axis oriented, paralleling to the substrate plane. Green exciton emission at 525 nm was observed in the film, and the explanations for it were given.

Patterning and optical properties rhodamine B-doped organic-inorganic silica films fabricated by sol-gel soft lithography

Abstract Rhodamine B (RB)-doped organic–inorganic silica films and their patterning were fabricated by a sol–gel process combined with a soft lithography. The resulted film samples were characterized by atomic force microscope (AFM), optical microscope and UV/Vis absorption and photoluminescence excitation and emission spectra. The effects of the concentration of the RB dye and heat treatment temperature on the optical properties of the hybrid silica films have been studied. Four kinds of patterning structures with film line widths of 5, 10, 20 and 50 μm have been obtained by micromolding in capillaries by a soft lithography technique. The RB-doped hybrid silica films present a red color, with an excitation and emission bands around 564 and 585 nm, respectively. With increasing the RB concentration, the emission intensity of the RB-doped hybrid silica films increases and the emission maximum presents a red shift. The emission intensity of the films decreases with increasing the heat treatment temperatures.

Micro-contact printing of graphene oxide nanosheets for fabricating patterned polymer brushes

A robust strategy is developed to fabricate micro-patterned graphene oxide (GO) films on a hydroxylated surface via micro-contact printing induced supramolecular self-assembly. Existing photoactive sites on the surface of GO allow further amplification by growing polymer brushes via self-initiated photografting and photopolymerization (SIPGP).