S. P. Obenschain

The Nike KrF laser facility: Performance and initial target experiments

Krypton‐fluoride (KrF) lasers are of interest to laser fusion because they have both the large bandwidth capability (≳THz) desired for rapid beam smoothing and the short laser wavelength (1/4 μm) needed for good laser–target coupling. Nike is a recently completed 56‐beam KrF laser and target facility at the Naval Research Laboratory. Because of its bandwidth of 1 THz FWHM (full width at half‐maximum), Nike produces more uniform focal distributions than any other high‐energy ultraviolet laser. Nike was designed to study the hydrodynamic instability of ablatively accelerated planar targets. First results show that Nike has spatially uniform ablation pressures (Δp/p<2%). Targets have been accelerated for distances sufficient to study hydrodynamic instability while maintaining good planarity. In this review we present the performance of the Nike laser in producing uniform illumination, and its performance in correspondingly uniform acceleration of targets.

Observation of Rayleigh-Taylor Growth to Short Wavelengths on Nike

The uniform and smooth focal profile of the Nike KrF laser [S. Obenschain et al., Phys. Plasmas 3, 2098 (1996)] was used to ablatively accelerate 40 μm thick polystyrene planar targets with pulse shaping to minimize shock heating of the compressed material. The foils had imposed small-amplitude sinusoidal wave perturbations of 60, 30, 20, and 12.5 μm wavelength. The shortest wavelength is near the ablative stabilization cutoff for Rayleigh–Taylor growth. Modification of the saturated wave structure due to random laser imprint was observed. Excellent agreement was found between the two-dimensional simulations and experimental data for most cases where the laser imprint was not dominant.

Shock ignition target design for inertial fusion energy

Continuing work in the design of shock ignition targets is described. Because of reduced implosion velocity requirements, low target adiabats, and efficient drive by short wavelength lasers, these targets produce high gain (>100) at laser energies well below 1 MJ. Effects of hydrodynamic instabilities such as Rayleigh–Taylor or Richtmyer–Meshkov are greatly reduced in these low-aspect ratio targets. Of particular interest is the optimum ratio of ignitor to compression pulse energy. A simple pellet model and simulation-derived coupling coefficients are used to analyze optimal fuel assembly, and determine that shock ignition allows enough control to create theoretically optimum assemblies. The effects on target design due to constraints on the compression and ignitor pulse intensities are also considered and addressed. Significant sensitivity is observed from low-mode perturbations because of large convergence ratios, but a more powerful ignitor can mitigate this.

Measurements of laser-imprinted perturbations and Rayleigh–Taylor growth with the Nike KrF laser

Nike is a 56 beam Krypton Fluoride (KrF) laser system using Induced Spatial Incoherence (ISI) beam smoothing with a measured focal nonuniformity 〈ΔI/I〉 of 1% rms in a single beam [S. Obenschain et al., Phys. Plasmas 3, 1996 (2098)]. When 37 of these beams are overlapped on the target, we estimate that the beam nonuniformity is reduced by 37, to (ΔI/I)≅0.15% (excluding short-wavelength beam-to-beam interference). The extraordinary uniformity of the laser drive, along with a newly developed x-ray framing diagnostic, has provided a unique facility for the accurate measurements of Rayleigh–Taylor amplified laser-imprinted mass perturbations under conditions relevant to direct-drive laser fusion. Data from targets with smooth surfaces as well as those with impressed sine wave perturbations agree with our two-dimensional (2-D) radiation hydrodynamics code that includes the time-dependent ISI beam modulations. A 2-D simulation of a target with a 100 A rms randomly rough surface finish driven by a completely unif...

Direct observation of mass oscillations due to ablative Richtmyer–Meshkov instability and feedout in planar plastic targets

Perturbations that seed Rayleigh–Taylor (RT) instability in laser-driven targets form during the early-time period. This time includes a shock wave transit from the front to the rear surface of the target, and a rarefaction wave transit in the opposite direction. During this time interval, areal mass perturbations caused by all sources of nonuniformity (laser imprint, surface ripple) are expected to oscillate. The first direct experimental observations of the areal mass oscillations due to ablative Richtmyer–Meshkov (RM) instability and feedout followed by the RT growth of areal mass modulation are discussed. The experiments were made with 40–99 μm thick planar plastic targets rippled either on the front or on the rear with a sine wave ripple with either 30 or 45 μm wavelength and with 0.5, 1, or 1.5 μm amplitude. Targets were irradiated with 4 ns long Nike KrF laser pulses at ∼50 TW/cm2. The oscillations were observed with our novel diagnostic technique, a monochromatic x-ray imager coupled to a streak c...

Large area electron beam pumped krypton fluoride laser amplifier

Nike is a recently completed multi-kilojoule krypton fluoride (KrF) laser that has been built to study the physics of direct drive inertial confinement fusion. This paper describes in detail both the pulsed power and optical performance of the largest amplifier in the Nike laser, the 60 cm amplifier. This is a double pass, double sided, electron beam-pumped system that amplifies the laser beam from an input of 50 J to an output of up to 5 kJ. It has an optical aperture of 60 cm × 60 cm and a gain length of 200 cm. The two electron beams are 60 cm high × 200 cm wide, have a voltage of 640 kV, a current of 540 kA, and a flat top power pulse duration of 250 ns. A 2 kG magnetic field is used to guide the beams and prevent self-pinching. Each electron beam is produced by its own Marx/pulse forming line system. The amplifier has been fully integrated into the Nike system and is used on a daily basis for laser-target experiments.

Electron beam pumped KrF lasers for fusion energy

Abstract : Direct drive with krypton fluoride (KrF) lasers is an attractive approach to inertial fusion energy (IFE): KrF lasers have outstanding beam spatial uniformity, which reduces the seed for hydrodynamic instabilities; they have short wavelength (248 nm) that increases the rocket efficiency and raises the threshold for deleterious laser-plasma instabilities; they have the capability for zooming , i.e. decreasing the spot size to follow an imploding pellet and thereby increase efficiency; and they have a modular architecture, which reduces development costs. Numerical 1-D simulations have shown that a target driven by a KrF laser can have a gain above 125 [1,2], which is ample for a fusion system. Simulations of the pellet burn in 2-D and 3-D are underway. In addition to these laser-target advantages, the Sombrero Power Plant study showed a KrF based system could lead to an economically attractive power plant [3]. In view of these advances, several world-wide programs are underway to develop KrF lasers for fusion energy. These include programs in Japan [4, 5], China [6], Russia [7], and The United Kingdom [8]. There was also a large program in the United States [9]. The paper here concentrates on current research in the US with two lasers at the Naval Research Laboratory: The Electra laser [10] is a 400-700 J repetitively pulsed system that is being used to develop the technologies that meet the fusion requirements for rep-rate, durability, efficiency and cost. The Nike laser [11] is a 3-5 kJ single shot device that is used to study KrF issues with full-scale electron beam diodes.

Effects of Thin High-z Layers on the Hydrodynamics of Laser-Accelerated Plastic Targets

Experimental results and simulations that study the effects of thin metallic layers with high atomic number (high-Z) on the hydrodynamics of laser accelerated plastic targets are presented. These experiments employ a laser pulse with a low-intensity foot that rises into a high-intensity main pulse. This pulse shape simulates the generic shape needed for high-gain fusion implosions. Imprint of laser nonuniformity during start up of the low intensity foot is a well-known seed for hydrodynamic instability. Large reductions are observed in hydrodynamic instability seeded by laser imprint when certain minimum thickness gold or palladium layers are applied to the laser-illuminated surface of the targets. The experiment indicates that the reduction in imprint is at least as large as that obtained by a 6 times improvement in the laser uniformity. Simulations supported by experiments are presented showing that during the low intensity foot the laser light can be nearly completely absorbed by the high-Z layer. X ra...

Effects of radiation on direct-drive laser fusion targets

The role played by radiation in the radiation-preheated direct-drive laser fusion target design is discussed. The soft x-rays emitted during the foot of the laser pulse—at a few 1012 W/cm2—preheat the low-opacity foam ablator which helps to control the Rayleigh–Taylor instability. The foam opacity is, however, thick enough to stop that radiation, keeping the fuel on a low adiabat. Radiation effects are also important in the blow-off corona of the target because they establish a long scale-length plasma. This may help to shield the ablation region from the nonuniformities in the laser absorption.

Pathway to a lower cost high repetition rate ignition facility

An approach to a high-repetition ignition facility based on direct drive with the krypton-fluoride laser is presented. The objective is development of a “Fusion Test Facility” that has sufficient fusion power to be useful as a development test bed for power plant materials and components. Calculations with modern pellet designs indicate that laser energies well below a megajoule may be sufficient. A smaller driver would result in an overall smaller, less complex and lower cost facility. While this facility might appear to have most direct utility to inertial fusion energy, the high flux of neutrons would also be able to address important issues concerning materials and components for other approaches to fusion energy. The physics and technological basis for the Fusion Test Facility are presented along with a discussion of its applications.