Sai Venkatesh Pingali

Breakdown of Cell Wall Nanostructure in Dilute Acid Pretreated Biomass

The generation of bioethanol from lignocellulosic biomass holds great promise for renewable and clean energy production. A better understanding of the complex mechanisms of lignocellulose breakdown during various pretreatment methods is needed to realize this potential in a cost and energy efficient way. Here we use small-angle neutron scattering (SANS) to characterize morphological changes in switchgrass lignocellulose across molecular to submicrometer length scales resulting from the industrially relevant dilute acid pretreatment method. Our results demonstrate that dilute acid pretreatment increases the cross-sectional radius of the crystalline cellulose fibril. This change is accompanied by removal of hemicellulose and the formation of R(g) ∼ 135 A lignin aggregates. The structural signature of smooth cell wall surfaces is observed at length scales larger than 1000 A, and it remains remarkably invariable during pretreatment. This study elucidates the interplay of the different biomolecular components in the breakdown process of switchgrass by dilute acid pretreatment. The results are important for the development of efficient strategies of biomass to biofuel conversion.

Common processes drive the thermochemical pretreatment of lignocellulosic biomass

Lignocellulosic biomass, a potentially important renewable organic source of energy and chemical feedstock, resists degradation to glucose in industrial hydrolysis processes and thus requires expensive thermochemical pretreatments. Understanding the mechanism of biomass breakdown during these pretreatments will lead to more efficient use of biomass. By combining multiple probes of structure, sensitive to different length scales, with molecular dynamics simulations, we reveal two fundamental processes responsible for the morphological changes in biomass during steam explosion pretreatment: cellulose dehydration and lignin-hemicellulose phase separation. We further show that the basic driving forces are the same in other leading thermochemical pretreatments, such as dilute acid pretreatment and ammonia fiber expansion.

Self-Assembly of Tobacco Mosaic Virus at Oil/Water Interfaces

The oil/water interfacial assembly of tobacco mosaic virus (TMV) has been studied in situ by tensiometry and small-angle X-ray and neutron scattering (SAXS and SANS). TMV showed different orientations at the perfluorodecalin/water interface, depending on the initial TMV concentration in the aqueous phase. At low TMV concentration, the rods oriented parallel to the interface, mediating the interfacial interactions at the greatest extent per particle. At high TMV concentrations, the rods were oriented normal to the interface, mediating the interfacial interactions and also neutralizing inter-rod electrostatic repulsion. We found that the inter-rod repulsive forces between TMVs dominated the in-plane packing, which was strongly affected by the ionic strength and the bulk solution but not by the pH in the range of pH = 6-8.

Cross-Strand Pairing and Amyloid Assembly

Amino acid cross-strand pairing interactions along a beta-sheet surface have been implicated in protein beta-structural assembly and stability, yet the relative contributions have been difficult to evaluate directly. Here we develop the central core sequence of the Abeta peptide associated with Alzheimers disease, Abeta(16-22), as an experimental system for evaluating these interactions. The peptide allows for internal comparisons between electrostatic and steric interactions within the beta-sheet and an evaluation of these cross-strand pair contributions to beta-sheet registry. A morphological transition from fibers to hollow nanotubes arises from changes in beta-sheet surface complementarity and provides a convenient indicator of the beta-strand strand registry. The intrinsic beta-sequence and pair correlations are critical to regulate secondary assembly. These studies provide evidence for a critical desolvation step that is not present in most models of the nucleation-dependent pathway for amyloid assembly.

Interfacial assembly of turnip yellow mosaic virus nanoparticles.

An extensive study of the factors that affect the interfacial assembly of bionanoparticles at the oil/water (O/W) interface is reported. Bionanoparticles, such as viruses, have distinctive structural properties due to the unique arrangement of their protein structures. The assembly process of such bionanoparticles at interfaces is governed by factors including the ionic strength and pH of the aqueous layer, concentration of the particles, and nature of the oil phase. This study highlights the impact of these factors on the interfacial assembly of bionanoparticles at the O/W interface using native turnip yellow mosaic virus (TYMV) as the prototype. Robust monolayer assemblies of TYMV were produced by self-assembly at the O/W interface using emulsions and planar interfaces. TYMV maintained its structure and integrity under different assembly conditions. For the emulsion droplets, they were fully covered with TYMV as evidenced by transmission electron microscopy (TEM) and scanning force microscopy (SFM). Tensiometry and small-angle neutron scattering (SANS) further supported this finding. Although the emulsions offered a complete coverage by TYMV particles, they lacked long-range ordering due to rapid exchange at the interface. By altering the assembly process, highly ordered, hexagonal arrays of TYMV were obtained at planar O/W interfaces. The pH, ionic strength, and viscosity of the solution played a crucial role in enhancing the lateral ordering of TYMV assembled at the planar O/W interface. This interfacial ordering of TYMV particles was further stabilized by introduction of a positively charged dehydroabietyl amine (DHAA) in the organic phase which held the assembly together by electrostatic interactions. The long-range array formation was observed using TEM and SFM. The results presented here illustrate that the interfacial assembly at the O/W interface is a versatile approach to achieve highly stable self-assembled structures.

Effect of lignin content on changes occurring in poplar cellulose ultrastructure during dilute acid pretreatment

BackgroundObtaining a better understanding of the complex mechanisms occurring during lignocellulosic deconstruction is critical to the continued growth of renewable biofuel production. A key step in bioethanol production is thermochemical pretreatment to reduce plant cell wall recalcitrance for downstream processes. Previous studies of dilute acid pretreatment (DAP) have shown significant changes in cellulose ultrastructure that occur during pretreatment, but there is still a substantial knowledge gap with respect to the influence of lignin on these cellulose ultrastructural changes. This study was designed to assess how the presence of lignin influences DAP-induced changes in cellulose ultrastructure, which might ultimately have large implications with respect to enzymatic deconstruction efforts.ResultsNative, untreated hybrid poplar (Populus trichocarpa x Populus deltoids) samples and a partially delignified poplar sample (facilitated by acidic sodium chlorite pulping) were separately pretreated with dilute sulfuric acid (0.10 M) at 160°C for 15 minutes and 35 minutes, respectively . Following extensive characterization, the partially delignified biomass displayed more significant changes in cellulose ultrastructure following DAP than the native untreated biomass. With respect to the native untreated poplar, delignified poplar after DAP (in which approximately 40% lignin removal occurred) experienced: increased cellulose accessibility indicated by increased Simons’ stain (orange dye) adsorption from 21.8 to 72.5 mg/g, decreased cellulose weight-average degree of polymerization (DPw) from 3087 to 294 units, and increased cellulose crystallite size from 2.9 to 4.2 nm. These changes following DAP ultimately increased enzymatic sugar yield from 10 to 80%.ConclusionsOverall, the results indicate a strong influence of lignin content on cellulose ultrastructural changes occurring during DAP. With the reduction of lignin content during DAP, the enlargement of cellulose microfibril dimensions and crystallite size becomes more apparent. Further, this enlargement of cellulose microfibril dimensions is attributed to specific processes, including the co-crystallization of crystalline cellulose driven by irreversible inter-chain hydrogen bonding (similar to hornification) and/or cellulose annealing that converts amorphous cellulose to paracrystalline and crystalline cellulose. Essentially, lignin acts as a barrier to prevent cellulose crystallinity increase and cellulose fibril coalescence during DAP.

MOLECULAR ORDERING AND PHASE TRANSITIONS IN ALKANOL MONOLAYERS AT THE WATER-HEXANE INTERFACE

The interface between bulk water and bulk hexane solutions of n-alkanols (H(CH(2))(m)OH, where m=20, 22, 24, or 30) is studied with x-ray reflectivity, x-ray off-specular diffuse scattering, and interfacial tension measurements. The alkanols adsorb to the interface to form a monolayer. The highest density, lowest temperature monolayers contain alkanol molecules with progressive disordering of the chain from the -CH(2)OH to the -CH(3) group. In the terminal half of the chain that includes the -CH(3) group the chain density is similar to that observed in bulk liquid alkanes just above their freezing temperature. The density in the alkanol headgroup region is 10% greater than either bulk water or the ordered headgroup region found in alkanol monolayers at the water-vapor interface. We conjecture that this higher density is a result of water penetration into the headgroup region of the disordered monolayer. A ratio of 1:3 water to alkanol molecules is consistent with our data. We also place an upper limit of one hexane to five or six alkanol molecules mixed into the alkyl chain region of the monolayer. In contrast, H(CH(2))(30)OH at the water-vapor interface forms a close-packed, ordered phase of nearly rigid rods. Interfacial tension measurements as a function of temperature reveal a phase transition at the water-hexane interface with a significant change in interfacial excess entropy. This transition is between a low temperature interface that is nearly fully covered with alkanols to a higher temperature interface with a much lower density of alkanols. The transition for the shorter alkanols appears to be first order whereas the transition for the longer alkanols appears to be weakly first order or second order. The x-ray data are consistent with the presence of monolayer domains at the interface and determine the domain coverage (fraction of interface covered by alkanol domains) as a function of temperature. This temperature dependence is consistent with a theoretical model for a second order phase transition that accounts for the domain stabilization as a balance between line tension and long range dipole forces. Several aspects of our measurements indicate that the presence of domains represents the appearance of a spatially inhomogeneous phase rather than the coexistence of two homogeneous phases.

The Bio-SANS instrument at the High Flux Isotope Reactor of Oak Ridge National Laboratory

Small-angle neutron scattering (SANS) is a powerful tool for characterizing complex disordered materials, including biological materials. The Bio-SANS instrument of the High Flux Isotope Reactor of Oak Ridge National Laboratory (ORNL) is a high-flux low-background SANS instrument that is, uniquely among SANS instruments, dedicated to serving the needs of the structural biology and biomaterials communities as an open-access user facility. Here, the technical specifications and performance of the Bio-SANS are presented. Sample environments developed to address the needs of the user program of the instrument are also presented. Further, the isotopic labeling and sample preparation capabilities available in the Bio-Deuteration Laboratory for users of the Bio-SANS and other neutron scattering instruments at ORNL are described. Finally, a brief survey of research performed using the Bio-SANS is presented, which demonstrates the breadth of the research that the instruments user community engages in.

Comparison of changes in cellulose ultrastructure during different pretreatments of poplar

Abstract One commonly cited factor that contributes to the recalcitrance of biomass is cellulose crystallinity. The present study aims to establish the effect of several pretreatment technologies on cellulose crystallinity, crystalline allomorph distribution, and cellulose ultrastructure. The observed changes in the cellulose ultrastructure of poplar were also related to changes in enzymatic hydrolysis, a measure of biomass recalcitrance. Hot-water, organo-solv, lime, lime-oxidant, dilute acid, and dilute acid-oxidant pretreatments were compared in terms of changes in enzymatic sugar release and then changes in cellulose ultrastructure measured by 13C cross polarization magic angle spinning nuclear magnetic resonance and wide-angle X-ray diffraction. Pretreatment severity and relative chemical depolymerization/degradation were assessed through compositional analysis and high-performance anion-exchange chromatography with pulsed amperometric detection. Results showed minimal cellulose ultrastructural changes occurred due to lime and lime-oxidant pretreatments, which at short residence time displayed relatively high enzymatic glucose yield. Hot water pretreatment moderately changed cellulose crystallinity and crystalline allomorph distribution, yet produced the lowest enzymatic glucose yield. Dilute acid and dilute acid-oxidant pretreatments resulted in the largest increase in cellulose crystallinity, para-crystalline, and cellulose-Iβ allomorph content as well as the largest increase in cellulose microfibril or crystallite size. Perhaps related, compositional analysis and Klason lignin contents for samples that underwent dilute acid and dilute acid-oxidant pretreatments indicated the most significant polysaccharide depolymerization/degradation also ensued. Organo-solv pretreatment generated the highest glucose yield, which was accompanied by the most significant increase in cellulose microfibril or crystallite size and decrease in relatively lignin contents. Hot-water, dilute acid, dilute acid-oxidant, and organo-solv pretreatments all showed evidence of cellulose microfibril coalescence.

Nucleobase-Directed Amyloid Nanotube Assembly

Cytosine nucleobases were successfully incorporated into the side chain of the self-assembling amyloid peptide fragment HHQALVFFA to give ccAQLVFFA. At a pH range of 3-4, where cytosine is expected to be partially protonated, small-angle X-ray scattering analyses revealed the nucleobase peptide assembles to be well-defined nanotubes with an outer diameter of 24.8 nm and wall thicknesses of 3.3 nm. FT-IR and X-ray diffraction confirmed beta-sheet-rich assembly with the characteristic cross-beta architecture of amyloid. The beta-sheet registry, determined by measuring (13)CO-(13)CO backbone distances with solid-state NMR and linear dichroism, placed the cytosine bases roughly perpendicular to the nanotube axis, resulting in a model where the complementary interactions between the cytosine bases increases beta-sheet stacking to give the nanotube architecture. These scaffolds then extend the templates used to encode biological information beyond the nucleic acid duplexes and into covalent networks whose self-assembly is still defined by a precise complementarity of the side-chain registry.