Sang-Sik Jang
Chungnam National University
Network
Latest external collaboration on country level. Dive into details by clicking on the dots.
Publication
Featured researches published by Sang-Sik Jang.
Journal of the Korean wood science and technology | 2014
Tae-Woo Kim; Bin Ha; Sang-Sik Jang
트러스는 북미 지역이나 호주, 뉴질랜드 등 목조주택이 일반화된 지역에 주택을 시공함에 있어 주로 사용되는 구조부재로써, 공장에서 제작되며 현장에서 제작하기는 힘들다. 반면에, 목조주택규모가 작은 국내에서는 제작비, 운반비, 경험부족 등을 이유로 트러스의 사용이 매우 제한적이며 대부분의 현장에서 서까래 공법으로 시공을 하고 있는 실정이다. 본 연구에서는 일반적으로 사용되는 금속제 트러스 플레이트가 아닌 현장에 버려지는 OSB를 덧댐판(gusset)으로 사용하여 현장에서 간단하게 제작이 가능한 형태의 경사트러스와 수평트러스를 제작해 보고 그 휨강도를 측정해 봄으로써 소규모 단독주택이 대부분인 목조주택 현장에서 사용가능 여부를 평가하고자 하였다. 경사트러스의 허용하중을 실제하중과 비교하였을 때, 지간거리 6 m에서 지붕경사트러스의 허용하중 및 실제하중은 10.60 kN 및 5.26 kN로 나타내어 사용하기에 충분하다고 판단된다. 지간거리 6 m의 수평트러스를 바닥장선으로 사용할 경우, 허용하중 및 실제하중은 7.18 kN 및 7.43 kN로 나타나 허용하중이 약간 낮기는 하지만 그 차이가 크지 않으므로 구조보강 및 부재의 변경 등을 통하여 사용이 가능한 것으로 판단된다. 【Trusses are widely used for wooden houses in the areas where wood construction in generalized for residential housings such as North America, Australian, New Zealand. In Korea, joist and rafter system is generally used because of the production cost, transportation cost and lack of experience required for truss manufacturing. In this study, roof trusses and flat trusses were manufactured by using oriented strand board (OSB) gusset plates for field assembly and tested under bending load to obtain the allowable loads. The allowable load and the actual load of 6m span roof trusses were 10.60 kN and 5.26 kN, respectively, which is regarded to be sufficient for use in construction. The allowable load and the actual load of 6m span floor flat trusses were 7.18 kN and 7.43 kN, respectively. For flat trusses, the allowable load is slightly lower than the actual load but the difference in very small, and it is thought that flat trusses can be used for construction by applying small change of structures and members.】
Journal of the Korean wood science and technology | 2014
Yun-Hui Kim; Sang-Sik Jang
국토면적의 약 64%가 산림으로 구성되어 OECD 국가 중 네 번째로 산림면적의 비율이 높은 편임에도 원목 생산보다는 녹화에 초점을 맞추어 진행된 조림의 결과로 국내 목재자급률은 약 16.2%에 불구하다. 본 연구에서는 국산 간벌재로부터 소경각재를 생산하여 다중접착을 통해 기둥과 보 등의 다양한 구조용 집성재 제조하기 위하여 핑거조인트가 포함된 소경각재의 휨 성능을 핑거조인트가 없는 소경각재의 휨 성능과 비교하였으며 시험결과를 ASTM D2915에 따라 통계처리를 실시하여 허용응력을 산출하고 상호 비교 평가하였다. 기존의 구조용 집성재 생산라인에서 50 mm 이하의 층재에 대하여 사용하였던 핑거조인트 기계를 사용하여 제조된 핑거조인트 소경각재는 핑거조인트가 없는 부재에 비하여 50% 이하의 휨강도를 나타낸 반면 개선된 핑거조인트 방법을 적용하여 제조된 핑거조인트 부재는 약 80% 정도의 휨강도를 나타내었다. 또한, ASTM D 2915에 따라 핑거조인트가 없는 소경각재 및 핑거조인트가 포함된 소경각재의 허용 휨응력은 각각 12 MPa 및 11.4 MPa로 나타났다. 핑거조인트가 있는 소경각재의 경우에 핑거조인트가 없는 부재보다 강도의 편차가 적었으며, MOR은 약 80% 수준을 나타내었으나 허용 휨응력은 약 95% 수준을 나타내었다. 【Despite Korea forest take 63.7% of the nations territory, productivity of domestic structural lumber is low. Studies of domestic small lumbers need to be improved domestic structural timber productivity. In this study, small diameter lumber and finger joint small diameter lumber took bending test to calculate MOE and MOR. MOE of small diameter lumber was
Journal of the Korean wood science and technology | 2010
Sang-Sik Jang; Yun-Hui Kim; Il-Joong Shin
9.3kN/mm^2
Bioresources | 2017
Ho-Yang Kang; Won-Hee Lee; Sang-Sik Jang; Chun-Won Kang
and MOE of finger joint small diameter lumber was
Journal of the Korean wood science and technology | 2001
Chun-Won Kang; Tsutsumi Juichi; Sang-Sik Jang
15.4kN/mm^2
Journal of the Korean wood science and technology | 2002
Sang-Sik Jang
. Allowable standard bending stress of small diameter lumber and finger joint small diameter lumber was calculated according to ASTM D 2915. Standard allowable bending stress of small diameter lumber was
Journal of the Korean wood science and technology | 2017
Sang-Sik Jang; Been Ha
12N/mm^2
Journal of Wood Science | 2017
Chengyuan Li; Chun-Won Kang; Ho-Yang Kang; Sang-Sik Jang
and standard allowable bending stress of finger joint small diameter lumber was
Korean Journal of Agricultural Science | 2011
Yun-Hui Kim; Sang-Sik Jang; Il-Joong Shin
11N/mm^2
Korean Journal of Agricultural Science | 2011
Yun-Hui Kim; Il-Joong Shin; Sang-Sik Jang
. Standard allowable bending stress of finger joint small diameter lumber should be considered to design structural beam members.】