Sang Wan Shin

A study on the in-vitro wear of the natural tooth structure by opposing zirconia or dental porcelain

PURPOSE This study was conducted to evaluate clinical validity of a zirconia full-coverage crown by comparing zirconias wear capacity over antagonistic teeth with that of feldspathic dental porcelain. MATERIALS AND METHODS The subject groups were divided into three groups: the polished feldspathic dental porcelain group (Group 1), the polished zirconia group (Group 2), and the polished zirconia with glazing group (Group 3). Twenty specimens were prepared from each group. Each procedure such as plasticity, condensation, and glazing was conducted according to the manufacturers manual. A wear test was conducted with 240,000 chewing cycles using a dual-axis chewing simulator. The degree of wear of the antagonistic teeth was calculated by measuring the volume loss using a three-dimensional profiling system and ANSUR 3D software. The statistical significance of the measured degree of wear was tested with a significant level of 5% using one-way ANOVA and the Tukey test. RESULTS The degrees of wear of the antagonistic teeth were 0.119 ± 0.059 mm3 in Group 1, 0.078 ± 0.063 mm3 in Group 3, and 0.031 ± 0.033 mm3 in Group 2. Statistical significance was found between Group 1 and Groups 2 and between Group 2 and 3, whereas no statistical significance was found between Group 1 and Group 3. CONCLUSION Despite the limitations of this study on the evaluation of antagonistic teeth wear, the degree of antagonistic tooth wear was less in zirconia than feldspathic dental porcelain, representing that the zirconia may be more beneficial in terms of antagonistic tooth wear.

Temperature change in pig rib bone during implant site preparation by low-speed drilling

Objectives The purpose of this study was to evaluate the temperature change during lowspeed drilling using infrared thermography. Material and Methods Pig ribs were used to provide cortical bone of a similar quality to human mandible. Heat production by three implant drill systems (two conventional drilling systems and one low-speed drilling system) was evaluated by measuring the bone temperature using infrared thermography. Each system had two different bur sizes. The drill systems used were twist drill (2.0 mm/2.5 mm), which establishes the direction of the implant, and finally a 3.0 mm-pilot drill. Thermal images were recorded using the IRI1001 system (Infrared Integrated Systems Ltd.). Baseline temperature was 31±1ºC. Measurements were repeated 10 times, and a static load of 10 kg was applied while drilling. Data were analyzed using descriptive statistics. Statistical analysis was conducted with two-way ANOVA. Results and Conclusions Mean values (n=10 drill sequences) for maximum recorded temperature (Max TºC), change in temperature (∆TºC) from baseline were as follows. The changes in temperature (∆TºC) were 1.57ºC and 2.46ºC for the lowest and the highest values, respectively. Drilling at 50 rpm without irrigation did not produce overheating. There was no significant difference in heat production between the 3 implant drill systems (p>0.05). No implant drill system produced heat exceeding 47ºC, which is the critical temperature for bone necrosis during low-speed drilling. Low-speed drilling without irrigation could be used during implant site preparation.

Relationship between articulation paper mark size and percentage of force measured with computerized occlusal analysis

PURPOSE Articulation paper mark size is widely accepted as an indicator of forceful tooth contacts. However, mark size is indicative of contact location and surface area only, and does not quantify occlusal force. The purpose of this study is to determine if a relationship exists between the size of paper marks and the percentage of force applied to the same tooth. MATERIALS AND METHODS Thirty dentate female subjects intercuspated into articulation paper strips to mark occlusal contacts on their maxillary posterior teeth, followed by taking photographs. Then each subject made a multi-bite digital occlusal force percentage recording. The surface area of the largest and darkest articulation paper mark (n = 240 marks) in each quadrant (n = 60 quadrants) was calculated in photographic pixels, and compared with the force percentage present on the same tooth. RESULTS Regression analysis shows a bi-variant fit of force % on tooth (P<.05). The correlation coefficient between the mark area and the percentage of force indicated a low positive correlation. The coefficient of determination showed a low causative relationship between mark area and force (r2 = 0.067). The largest paper mark in each quadrant was matched with the most forceful tooth in that same quadrant only 38.3% of time. Only 6 2/3% of mark surface area could be explained by applied occlusal force, while most of the mark area results from other factors unrelated to the applied occlusal force. CONCLUSION The findings of this study indicate that size of articulation paper mark is an unreliable indicator of applied occlusal force, to guide treatment occlusal adjustments.

Attachment systems for mandibular implant overdentures: a systematic review

PURPOSE The aim of this systematic review was to address treatment outcome according to attachment systems for mandibular implant overdentures in terms of implant survival rate, prosthetic maintenance and complications, and patient satisfaction. MATERIALS AND METHODS A systematic literature search was conducted using PubMed and hand searching of relevant journals considering inclusion and exclusion criteria. Clinical trial studies on mandibular implant overdentures until August, 2010 were selected if more than one type of overdenture attachment was reported. Twenty four studies from 1098 studies were finally included and the data on implant survival rate, prosthetic maintenance and complications, patient satisfaction were analyzed relative to attachment systems. RESULTS Four studies presented implant survival rates (95.8 - 97.5% for bar, 96.2 - 100% for ball, 91.7% for magnet) according to attachment system. Ten other studies presented an implant survival rate ranging from 93.3% to 100% without respect to the attachment groups. Common prosthetic maintenance and complications were replacement of an assay for magnet attachments, and activation of a matrix or clip for ball or bar attachments. Prosthetic maintenance and complications most commonly occurred in the magnet groups. Conflicting findings were found on the rate of prosthetic maintenance and complications comparing ball and bar attachments. Most studies showed no significant differences in patient satisfaction depending upon attachment systems. CONCLUSION The implant survival rate of mandibular overdentures seemed to be high regardless attachment systems. The prosthetic maintenance and complications may be influenced by attachment systems. However patient satisfaction may be independent of the attachment system.

Effect of software version and parameter settings on the marginal and internal adaptation of crowns fabricated with the CAD/CAM system

Objective This study investigated the marginal and internal adaptation of individual dental crowns fabricated using a CAD/CAM system (Sirona’s BlueCam), also evaluating the effect of the software version used, and the specific parameter settings in the adaptation of crowns. Material and Methods Forty digital impressions of a master model previously prepared were acquired using an intraoral scanner and divided into four groups based on the software version and on the spacer settings used. The versions 3.8 and 4.2 of the software were used, and the spacer parameter was set at either 40 μm or 80 μm. The marginal and internal fit of the crowns were measured using the replica technique, which uses a low viscosity silicone material that simulates the thickness of the cement layer. The data were analyzed using a Friedman two-way analysis of variance (ANOVA) and paired t-tests with significance level set at p<0.05. Results The two-way ANOVA analysis showed the software version (p<0.05) and the spacer parameter (p<0.05) significantly affected the crown adaptation. The crowns designed with the version 4.2 of the software showed a better fit than those designed with the version 3.8, particularly in the axial wall and in the inner margin. The spacer parameter was more accurately represented in the version 4.2 of the software than in the version 3.8. In addition, the use of the version 4.2 of the software combined with the spacer parameter set at 80 μm showed the least variation. On the other hand, the outer margin was not affected by the variables. Conclusion Compared to the version 3.8 of the software, the version 4.2 can be recommended for the fabrication of well-fitting crown restorations, and for the appropriate regulation of the spacer parameter.

Ridge preservation using demineralized bone matrix gel with recombinant human bone morphogenetic protein-2 after tooth extraction: a randomized controlled clinical trial.

PURPOSE The aim of the present randomized controlled trial was to determine the safety and efficacy of injectable demineralized bone matrix (DBM) gel combined with recombinant human bone morphogenetic protein-2 (rhBMP-2) on alveolar ridge preservation after tooth extraction. MATERIALS AND METHODS A total of 69 patients were randomly assigned to either a test group (n = 35) or a control group (n = 34). In the test group, DBM, together with rhBMP-2 (0.05 mg/mL; rhBMP-2/DBM) was transplanted into the extraction sockets. The control group received DBM alone. The safety of rhBMP-2/DBM was evaluated by oral examination, serum chemistry, and hematologic examination. The radiographic changes in alveolar bone height and width were measured using computed tomography scans performed immediately after transplant and again 3 months thereafter. RESULTS Healing was uneventful in all subjects, with no anticipated adverse events and no clinically significant changes in the serum chemistry and hematologic findings. No meaningful immune response was found among the study groups. No significant difference was found in the radiographic changes of alveolar bone height and width (P > .05). CONCLUSIONS This new injectable biomaterial can be used easily and safely in clinical applications.

Effects of anodized implants coated with Escherichia coli-derived rhBMP-2 in beagle dogs.

This study evaluated the effects of Escherichia coli-derived rhBMP-2 (ErhBMP-2) coated onto anodized implants to stimulate bone formation, osseointegration and vertical bone growth in a vertical bone defect model. Six young adult beagle dogs were used. After a 2-month bone healing period, anodized titanium implants (8mm in length) were placed 5.5mm into the mandibular alveolar ridge. Eighteen implants coated with ErhBMP-2 (BMP group) and another 18 uncoated implants (control group) were installed using a randomized split-mouth design. The implant stability quotient (ISQ) values were measured. Specimens were fabricated for histometric analysis to evaluate osseointegration and bone formation. The ISQ values at 8 weeks after implant placement were significantly higher in the BMP group than in the control group (p<0.05). Histological observations showed that the changes in bucco-lingual alveolar bone levels were higher in the BMP group than in the control group (p<0.05). The ErhBMP-2 coated anodized implants can stimulate bone formation and increase implant stability significantly on completely healed alveolar ridges in dogs. Further studies evaluating the effects of ErhBMP-2 on osseointegration in the bone-implant interface are warranted.

Risk assessment for clinical attachment loss of periodontal tissue in Korean adults

PURPOSE The purpose of this study was to assess the prevalence and extent of clinical attachment loss of periodontal tissue and to find out variables related to clinical attachment loss (CAL) in Korean adults older than 40 years of age. MATERIALS AND METHODS Data were collected from 2,519 subjects who were part of a cohort study conducted in Ansan city by Korea University Medical School for Korean Genome project. Age, sex, smoking, drinking, fast glucose, blood pressure, obesity and total cholesterol levels were examined. The oral examination included probing pocket depth, gingival recession and CAL of Ramfords teeth. The severity of periodontitis was classified based on the mean value of CAL. The relationship between each risk factor and the severity of CAL was independently estimated using the chi-square test, the test or one-way ANOVA. Multiple regression analysis was used to determine the significance of each factor in the periodontal disease. RESULTS The prevalences of clinical attachment between 1 and 3 mm, between 3 and < 5 mm, and ≥ 5 mm were 80.27%, 16.75% and < 1%, respectively. Although the univariate analysis showed age, gender, smoking, fasting glucose, blood pressure and total cholesterol levels were significantly related to the severity of CAL, multiple regression analysis indicated that age (P < .0001), gender (P < .0001) and smoking (P < .05) were only significantly related. CONCLUSION Older age, male gender and smoking were significant risk factor for the increase of CAL, and these may be useful indicators of periodontitis high-risk groups.

Alveolar ridge augmentation using anodized implants coated with Escherichia coli–derived recombinant human bone morphogenetic protein 2

OBJECTIVE The aim of this study was to examine the effect of Escherichia coli-derived recombinant human bone morphogenetic protein 2 (ErhBMP-2) coated onto anodized implant to stimulate local bone formation, including osseointegration and the vertical augmentation of the alveolar ridge. STUDY DESIGN Six young male adult beagle dogs were used. A crestal area was leveled on both sides of each test subject by removing minimal cortical bone using a round bur and without exposing cancellous bone. After a 2-month healing period, 3 anodized implants (length 8 mm, diameter 4 mm; Cowellmedi, Busan, Korea) were placed 5 mm into the mandibular alveolar ridge in either side. Each animal received 6 implants that were either coated with ErhBMP-2 (0.75 or 1.5 mg/mL concentration; Cowellmedi) or uncoated. This was performed using a randomized split-mouth design. A total of 36 implants were used for this study. Twelve noncoated implants were used as control, and 24 BMP-coated implants were used as our experimental group, which was further divided into 2 groups of 12 implants each with different BMP concentration of 0.75 and 1.5 mg/mL. Radiologic examinations were performed immediately after implant placement and 4 and 8 weeks after implant placement. The amount of bone augmentation was evaluated by measuring the distance from the uppermost point of the cover screw to the marginal bone. Implant stability quotient (ISQ) values were measured immediately after surgery and 8 weeks after implant placement. Statistical analysis was performed using one-way analysis of variance (SPSS version 17.0) and multiple-comparison tests. Statistical significance was established at the 95% confidence level. RESULTS Implants coated with ErhBMP-2 at 0.75 mg/mL (BMP 0.75 group) and 1.5 mg/mL (BMP 1.5 group) exhibited significant vertical bone formation compared with the control group (mean ± SD): 0.88 ± 0.94 versus 0.60 ± 0.64 versus -0.52 ± 0.64 mm, respectively; P < .05. There was a significant difference between the 3 groups in bone level change (P < .05). The BMP 0.75 and BMP 1.5 groups exhibited significant changes in ISQ compared with the control group: 8.17 ± 8.31 versus 11.50 ± 9.02 versus 2.17 ± 7.61, respectively; P < .05. CONCLUSION Within the limits of this study, the ErhBMP-2 coating on an anodized implant may stimulate vertical bone augmentation, which significantly increases implant stability on completely healed alveolar ridges.

The effect of immobilization of heparin and bone morphogenic protein-2 to bovine bone substitute on osteoblast-like cell' s function

PURPOSE This study was performed to investigate the ability of recombinant human-bone morphogenic protein-2 immobilized on a heparin-grafted bone substrate to enhance the osteoblastic functions. MATERIALS AND METHODS The Bio-Oss®, not coated with any material, was used as a control group. In rhBMP-2-Bio-Oss® group, rhBMP-2 was coated with Bio-Oss® using only deep and dry methods (50 ng/mL, 24 h). In heparinized rhBMP-2-Bio-Oss® group, dopamine was anchored to the surface of Bio-Oss®, and coated with heparin. rhBMP-2 was immobilized onto the heparinized- Bio-Oss® surface. The release kinetics of the rhBMP-2-Bio-Oss® and heparinized rhBMP-2-Bio-Oss® were analyzed using an enzyme-linked immunosorbent assay. The biological activities of the MG63 cells on the three groups were investigated via cytotoxicity assay, cell proliferation assay, alkaline phosphatase (ALP) measurement, and calcium deposition determination. Statistical comparisons were carried out by one-way ANOVA test. Differences were considered statistically significant at *P<.05 and **P<.001. RESULTS The heparinized rhBMP-2-Bio-Oss® showed more sustained release compared to the rhBMP-2-Bio-Oss® over an extended time. In the measurement of the ALP activity, the heparinized group showed a significantly higher ALP activity when compared with the non-heparinized groups (P<.05). The MG63 cells cultivated in the group with rhBMP-2 showed increased calcium deposition, and the MG63 cells from the heparinized group increased more than those that were cultivated in the non-heparinized groups. CONCLUSION Heparin increased the rhBMP-2 release amount and made sustained release possible, and heparinized Bio-Oss® with rhBMP-2 successfully improved the osteoblastic functions.