Santo Scalia

Analytical and preparative supercritical fluid extraction of Chamomile flowers and its comparison with conventional methods

Supercritical fluid extraction (SFE) was compared with Soxhlet extraction, steam distillation and maceration for the isolation of the active components present in chamomile flowerheads. The obtained fractions were analysed by GC-MS and reversed-phase HPLC. The yield of essential oil achieved by a 30-min extraction with pure CO2 at 90 atm and 40 degrees C was 4.4 times higher than that produced by steam distillation performed for 4 h. The recovery of the flavonoid apigenin obtained by supercritical CO2 after a 30-min extraction at 200 atm and 40 degrees C was 71.4% compared to Soxhlet extraction performed for 6 h and 124.6% compared to maceration performed for 3 days. However, the highly polar flavonoid apigenin-7-glucoside was not extracted by 100% CO2 (recovery values < 1.1%). Its extraction efficiency was markedly improved by the addition of the polar modifier methanol (5%, v/v) to the CO2 fluid, yet the obtained recoveries were unsatisfactory (14.6-19.5%). The SFE method was scaled-up for preparative applications using a pilot plant with three separation stages operating in series. Large-scale SFE was technically feasible with pure CO2 as the extracting fluid. However, the use of CO2 modified with organic solvents was not effective at the pilot-plant scale.

Study on glycolic acid delivery by liposomes and microspheres

Glycolic acid is used in many cosmetic products as exfoliant and moisturizer. Unfortunately, the greater glycolic acid cosmetic benefits the greater is the potential for skin irritation as far as burning. The aim of this work was to investigate the feasibility of topical controlled delivery systems loading glycolic acid in order to optimize the acid cosmetic properties lowering its side effects. For this purpose different types of microparticulate systems have been evaluated: liposomes, liposomes modified by chitosan addition and chitosan microspheres. Liposomes, composed of phosphatidylcholine and cholesterol (1:1 molar ratio) and with different glycolic acid/lipid molar ratio, were prepared by reverse phase evaporation method. Two types of interaction between liposomes and chitosan were investigated: chitosan addition into lipidic bilayer during liposome preparation and coating of already formed liposomes with chitosan. Glycolic acid loaded chitosan microspheres were prepared by the dry-in-oil emulsion method. The microparticulate systems were morphologically characterized by electron microscopy and particle size analysis. In vitro dissolution tests were performed to evaluate the feasibility of microparticulate systems in modulating glycolic acid release. The results obtained show that liposomes are always suitable to modulate glycolic acid release and that the best condition to achieve this control is obtained by the liposomal systems in which glycolic acid/lipid molar ratio is 5:1. Further significant release control is obtained by addition of chitosan into the liposomes, while chitosan microspheres are not able to control glycolic acid release even after crosslinking.

Chitosan gels for the vaginal delivery of lactic acid: relevance of formulation parameters to mucoadhesion and release mechanisms.

The aim of this work was to assess the effect of formulation parameters of a mucoadhesive vaginal gel based on chitosan and lactic acid, and to highlight its release mechanisms. Two molecular weight chitosans were used to prepare gels with 2 lactic acid concentrations. Both chitosan molecular weight and lactic acid concentration had a significant and mutually dependent influence on mucoadhesion, measured on pig vaginal mucosa. Similarly, the lactate release profiles were found to be dependent on lactic acid content and polymer molecular weight.One gel formulation based on the stoichiometric lactate to chitosan ratio was subjected to release test in media with 2 different counterions and increasing ionic strength. This test demonstrated that the lactate release is mainly due to ionic displacement.

In vitro degradation study of polyester microspheres by a new HPLC method for monomer release determination.

Biodegradable polyesters have increasing importance as materials used for the preparation of microspheres. The knowledge of their degradation process is important to prepare microparticulate delivery systems with suitable drug release rates. In this work an in vitro degradation study of empty and drug loaded microspheres is described. Three different polyesters were used: two poly-d, l-lactides of different molecular weight and a poly-d, l-lactide-co-glycolide (50:50). Diazepam has been chosen as the model drug. Solvent evaporation and spray-drying were used as preparation methods. To study the polymer degradation process, a new HPLC method is proposed for the direct and (in the case of the copolymer) simultaneous determination of the monomer(s): lactic acid (LA) and glycolic acid (GA). SEM and particle size analysis highlight the different characteristics of the particles, depending on their preparation method: spray-dried spheres result to be always smaller with respect to particles obtained by solvent evaporation. The results obtained indicate in particular that: the preparation methods play an important role in determining the degradation behaviour of microspheres, as unloaded spray-dried particles are characterized by a higher monomer release rate with respect to microspheres obtained by solvent evaporation; PLGA spheres degrade faster than PDLLA microparticles, according to the higher hydrophilicity of the copolymer; the two monomers are released at a different rate in the case of PLGA (faster for GA, slower for LA); the presence of diazepam increases the polymer degradation rate, with respect to empty particles.

Photostabilization Effect of Quercetin on the UV Filter Combination, Butyl Methoxydibenzoylmethane–Octyl Methoxycinnamate

The aim of the study was to investigate the effect of the natural antioxidant quercetin on the photostability of the most widely used combination of UVA (320–400 nm) and UVB (290–320 nm) filters, respectively butyl methoxydibenzoylmethane (BMDBM) and octyl methoxycinnamate (OMC). In order to reproduce the conditions prevalent in commercial sunscreen products, the stabilizing efficacy of quercetin was evaluated in model creams containing BMDBM (3%, wt/wt) together with OMC (4%, wt/wt) and exposed to a solar simulator at an irradiance corresponding to natural sunlight. Quercetin was found to enhance the photostability of the two UV filters in a concentration‐dependent way. Addition of quercetin to the sunscreen formulation significantly reduced the photodegradation of BMDBM and OMC from 40.3 ± 2.4 to 27.7 ± 2.6% and from 51.3 ± 2.1 to 42.2 ± 2.0%, respectively. Moreover, comparative photodegradation studies demonstrated that quercetin was much more effective and at a lower concentration than commonly used stabilizer (octocrylene) and antioxidants (vitamin E, butylated hydroxyanisole). In vitro determination of the UVB and UVA protection parameters showed that the quercetin‐based formulation fulfilled the official requirements on sunscreen products. Because of its photostabilizing and multiple antioxidant properties, quercetin represents a useful additive for the formulation of effective broad‐spectrum sunscreens containing BMDBM and OMC.

Incorporation of quercetin in lipid microparticles: Effect on photo- and chemical-stability

Lipid microparticles loaded with the flavonoid, quercetin were developed in order to enhance its stability in topical formulations. The microparticles were produced using tristearin as the lipid material and phosphatidylcholine as the emulsifier. The obtained lipoparticles were characterized by release studies, scanning electron microscopy and powder X-ray diffractometry. The quercetin loading was 12.1% (w/w). Free or microencapsulated quercetin was introduced in a model cream formulation (oil-in-water emulsion) and irradiated with a solar simulator. The extent of photodegradation was measured by high-performance liquid chromatography. The light-induced decomposition of quercetin in the cream vehicle was markedly decreased by incorporation into the lipid microparticles (the extent of degradation was 23.1+/-3.6% for non-encapsulated quercetin compared to 11.9+/-2.5% for the quercetin-loaded microparticles) and this photostabilization effect was maintained over time. Moreover, the chemical instability of quercetin, during 3-month storage of the formulations at room temperature and in the dark, was almost completely suppressed by the lipid microparticle system. Therefore incorporation of quercetin in lipoparticles represents an effective strategy to enhance its stability in dermatological products.

Migration of antioxidant additives from various polyolefinic plastics into oleaginous vehicles

The migration of the antioxidant additives pentaerythrityl tetrakis(3,5-di-tert-butyl-4-hydroxyphenyl)propionate (Irganox 1010) and tris(2,4-di-tert-butylphenyl)phosphite (Irgafos 168) from polyolefinic packaging into oily vehicles was investigated. The polyolefins included in the study were from the following classes: isotactic polypropylene homopolymer (PP), ethylene-co-propylene random copolymer (RACO), ethylene-propylene heterophasic copolymer and ethylene-propylene amorphous copolymer blend (EP) and high-density polyethylene (HDPE). Each polymer was additioned with Irganox 1010 (0.15%, w/w) and Irgafos 168 (0.15%, w/w) and processed into blown bottles. To study the antioxidant release process, plastic sheets were cut from the bottles and dipped for various time intervals into a mixture of five oils (caprylic/capric triglyceride, cyclomethicone, dicaprylyl ether, isohexadecane and C(12-15) alkyl benzoate) representative of lipophilic excipients used in pharmaceutical and cosmetic formulations. After exposure to the oil medium, the non-migrated Irganox 1010 and Irgafos 168 were recovered from the polymeric matrices using microwave-assisted extraction with ethyl acetate-hexane and assayed by HPLC. The leaching of the two antioxidants varied remarkably depending on the polyolefin crystallinity and structure. The amount of Irganox 1010 transferred into the contact medium at 25 degrees C decreased in the order EP>RACO>PP>HDPE. The same polyolefin ranking was observed in the case of Irgafos 168, except for PP and HDPE which exhibited similar depletion of this additive. Migration of Irgafos 168 was greater than that of Irganox 1010 and the release of both antioxidants increased at higher temperature (50 degrees C). The obtained data are useful for the selection of polyolefinic matrices as raw-materials for the production of pharmaceutical and cosmetic containers.

Bile acid separation.

A review of the methods available for the separation of bile acids is presented, highlighting the most recent developments. The major chromatographic techniques (TLC, GC, HPLC) and combined detection systems for the determination of bile acids are critically evaluated and their advantages and disadvantages discussed. Moreover, future directions in which progress might occur are also indicated. Capillary GC-MS is the more established method since it provides higher efficiency combined with greater sensitivity and specificity and has proven crucial in identifying unusual bile acids. However, it requires deconjugation and derivatization and hence the conjugated species must be inferred from the initial isolation procedure. HPLC is directly amenable to the different forms of bile acids, but it suffers from insufficient resolving power which can be enhanced by exploiting the mobile-phase selectivity. The development of HPLC detection systems with higher sensitivity and specificity than conventional HPLC-UV is reported. In particular, methods for the direct coupling of HPLC to MS are examined with special emphasis on soft ionization processes (thermospray, fast atom bombardment, ion spray). Finally, the analytical potential for bile acid assays of more recent techniques including supercritical fluid chromatography and capillary electrophoresis is evaluated.

Comparative studies of the influence of cyclodextrins on the stability of the sunscreen agent, 2-ethylhexyl-p-methoxycinnamate.

The effects of beta-cyclodextrin (beta-CD) and hydroxypropyl-beta-cyclodextrin (HP-beta-CD) on the base-catalyzed degradation and light-induced decomposition of the sunscreen agent, trans-2-ethylhexyl-p-methoxycinnamate (trans-EHMC) were investigated. Reversed-phase liquid chromatography was used to study the interaction between natural and modified cyclodextrins, added to the mobile phase, and the sunscreen. Among the available cyclodextrins (beta-CD, HP-beta-CD, hydroxypropyl-alpha-cyclodextrin and hydroxypropyl-gamma-cyclodextrin), only HP-beta-CD and beta-CD produced a significant decrease in the chromatographic retention of trans-EHMC. The complexation of the sunscreen agent with HP-beta-CD and beta-CD was confirmed by thermal analysis and nuclear magnetic resonance spectroscopy. beta-CD depressed the decomposition of trans-EHMC in alkaline solutions more effectively than HP-beta-CD. Moreover, the irradiation-induced degradation of the sunscreen agent in emulsion vehicles was reduced by complexation with beta-CD (the extent of degradation was 26.1% for the complex compared to 35.8% for free trans-EHMC) whereas HP-beta-CD had no significant effect. Therefore, the complex of beta-CD with trans-EHMC enhances the chemical- and photo-stability of the sunscreen agent. Moreover, it limits adverse interactions of the UV filter with other formulation ingredients.

Inclusion complexation of the sunscreen agent 2-ethylhexyl-p-dimethylaminobenzoate with hydroxypropyl-β-cyclodextrin: Effect on photostability

The interaction between the UV filter, 2‐ethylhexyl‐p‐dimethylaminobenzoate, and unmodified and modified α‐, β‐ or γ‐cyclodextrins was studied in water by phase‐solubility analysis.