Sergei Godeiro Fernandes Rabelo Caldas

Segmented arch or continuous arch technique? A rational approach

This study aims at revising the biomechanical principles of the segmented archwire technique as well as describing the clinical conditions in which the rational use of scientific biomechanics is essential to optimize orthodontic treatment and reduce the side effects produced by the straight wire technique.

Superelasticity and force plateau of nickel-titanium springs: an in vitro study

abstract Objective: This paper analyzed whether nickel-titanium closed coil springs (NTCCS) have a different superelastic (SE) behavior according to activation and whether their force plateau corresponds to that informed by the manufacturer. Methods: A total of 160 springs were divided into 16 subgroups according to their features and activated proportionally to the length of the extensible part (NiTi) of the spring (Y). The force values measured were analyzed to determine SE rates and force plateaus, which were mathematically calculated. These plateaus were compared to those informed by the manufacturer. Analysis of variance was accomplished followed by Tukey post-hoc test to detect and analyze differences between groups. Results: All subgroups were SE at the activation of 400% of Y length, except for: subgroups 4B and 3A, which were SE at 300%; subgroups 4E and 4G, which were SE at 500%; and subgroup 3C, which was SE at 600%. Subgroup 3B did not show a SE behavior. Force plateaus depended on activation and, in some subgroups and some activations, were similar to the force informed. Conclusions: Most of the springs showed SE behavior at 400% of activation. Force plateaus are difficult to compare due to lack of information provided by manufacturers.

Differences in the force system delivered by different beta-titanium wires in elaborate designs

Abstract Objective: Evaluation of the force system produced by four brands of b-Ti wires bent into an elaborate design. Methods: A total of 40 T-loop springs (TLS) hand-bent from 0.017 x 0.025-in b-Ti were randomly divided into four groups according to wire brand: TMATM(G1), BETA FLEXYTM (G2), BETA III WIRETM (G3) and BETA CNATM (G4). Forces and moments were recorded by a moment transducer, coupled to a digital extensometer indicator adapted to a testing machine, every 0.5 mm of deactivation from 5 mm of the initial activation. The moment-to-force (MF) ratio, the overlapping of the vertical extensions of the TLSs and the load-deflection (LD) ratio were also calculated. To complement the results, the Youngs module (YM) of each wire was determined by the slope of the load-deflection graph of a tensile test. The surface chemical composition was also evaluated by an energy dispersive X-ray fluorescence spectrometer. Results: All groups, except for G2, produced similar force levels initially. G3 produced the highest LD rates and G1 and G4 had similar amounts of overlap of the vertical extensions of the TLSs in neutral position. G1 and G3 delivered the highest levels of moments, and G2 and G3 produced the highest MF ratios. b-Ti wires from G3 produced the highest YM and all groups showed similar composition, except for G2. Conclusion: The four beta-titanium wires analyzed produced different force systems when used in a more elaborate design due to the fact that each wire responds differently to bends.

Effect of different bonding protocols on degree of monomer conversion and bond strength between orthodontic brackets and enamel

The objective of the present study was to evaluate the effect of different surface treatments and polymerization protocols on the bond strength of brackets to enamel, and the degree of conversion of the bonding agents. 120 bovine crowns were embedded in acrylic resin blocks and sanded. Next, the blocks were randomly assigned into 12 groups. Metal brackets were bonded to enamel according to the surface treatment factor (A: Phosphoric Acid; ATxt: Phosphoric Acid + Transbond XT Primer®; Tse: Transbond Plus Self Etching Primer®; and SBU: Scotchbond Universal®) and polymerization factor (R20: Radii-Cal®/20 seconds; V20: Valo Cordless®/20 seconds; and V3: Valo Cordless®/3 seconds). All samples were stored for 6 months (water, 37ºC) and then subjected to a shear bond strength test (SBS). Bond failures were classified according to the Adhesive Remnant Index (ARI) and analyzed with the Kruskal-Wallis and Mann-Whitney tests (5%). Using the same factors, 120 resin discs were made to assess the degree of conversion (DC) of the monomer. Data from the SBS (MPa) and DC (%) were analyzed by analysis of variance (2 factors) and Tukeys test (5%). For the SBS, the factors polymerization (R20 = 8.1B; V20 = 13.2A; V3 = 5.2C, p = 0.0001) and surface treatment (A = 3.1C; ATxt = 13.6A; Tse = 12.3A; SBU = 6.3B, p = 0.0001) were statistically significant among groups. The highest adhesion value were found for the ATxt/V20 group (22.2A) and the lowest value for the A/R20 group (1.2E). Regarding ARI, score 2 was the most prevalent in groups A, ATxt, V20 and V3, while score 4 was the most prevalent in the Tse, SBU and R20 groups, with no significant difference between them (p = 1.0). Regarding DC, the factors polymerization (R20 = 66.6A; V20 = 58.4B; V3 = 45.1C, p = 0.0001) and surface treatment (A = 52B, ATxt = 59.7A, Tse = 51.4B, SBU = 63.8A, p = 0.0001) were statistically significant. Tse was more sensitive to the variations in polymerization protocols than the other surface treatments. Treatment A did not present suitable bond strength or degree of conversion.

Estudo comparativo in vitro da resistência ao desgaste entre o cimento de ionômero de vidro pó/liquido e o encapsulado

Marilia Regalado Galvao Rabelo Caldas; Kathia Maria Fonseca de Brito; Diana Ferreira Gadelha de Araujo.

Influence of temperature and humidity on the long-term storage of latex and non-latex orthodontic elastics

Objectives The objective of this study was to evaluate the influence of long-term storage on latex and non-latex orthodontic elastics. Materials and methods The sample consisted of 300 orthodontic elastics, 150 latex and 150 non-latex (American Orthodontics® *(AO) and Morelli®) of medium force and a standard size of 3/16′′ divided into 20 groups, 10 for each manufacturer, with 15 specimens each. The groups (G1*–G10* and G1–G10) were made up based on the manufacturer, storage temperature (ambient and refrigerated), material, and ambient humidity (exposed and non-exposed). The elastics were stretched and their forces measured in five progressive increases of 100% of their inner diameter, starting at a level of 200% stretching, by the MESDAN LAB 3000® (MESDAN, Italy) testing machine. The tests were carried out at two different times: immediately in as-received state and again after 1 year. Data were analysed using SPSS 16.0 software, the Students t-test, one-way analysis of variance (ANOVA) and the Tukeys post-test. Results There was a statistically significant difference between the average forces exerted by the latex elastics compared to the non-latex elastics for all distention levels evaluated, except for 300%; however, the different storage conditions of temperature and humidity did not interfere in the mechanical properties. Conclusion Both the latex and non-latex elastics may be stored under any of the conditions tested in the present study, since there were no changes in the potential of the force exerted by the elastics in relation to their percentage stretch over a 1-year period.

Stability of beta-titanium T-loop springs preactivated by gradual curvature

ABSTRACT Objective: Evaluate changes in the force system of T-Loop Springs (TLS) preactivated by curvature, due to stress relaxation. Methods: Ninety TLSs measuring 6 x 10 mm, produced out with 0.017 x 0.025-in TMA® wire and preactived by gradual curvature, were randomly distributed into nine groups according to time point of evaluation. Group 1 was tested immediately after spring preactivation and stress relief, by trial activation. The other eight groups were tested after 24, 48 and 72 hours, 1, 2, 4, 8 and 12 weeks, respectively. Using a moment transducer coupled to a digital extensometer indicator adapted to a universal testing machine, the amount of horizontal force, moment and moment-to-force ratios were recorded at every 0.5 mm of deactivation from 5 mm of the initial activation, in an interbracket distance of 23 mm. Results: The horizontal forces decreased gradually among the groups (p< 0.001) and the moments showed a significant and slow decrease over time among the groups (p< 0.001). All groups produced similar M/F ratios (p= 0.532), with no influence of time. Conclusions: The TLSs preactivated by curvature suffered a gradual deformation over time, which affected the force system, specifically the moments, which affected the horizontal forces produced.