Sergey Shleev

Laccase-mediator systems and their applications: A review

The mechanism of operation of laccase-mediator systems (LMSs) in xenobiotic degradation mediated by “true” redox mediators and laccase enhancing agents is considered. Structural formulae of most common laccase mediators and compounds that can be used as agents enhancing the enzyme operation are presented. Examples of LMS application in biotechnology are described.

Mediatorless sugar/oxygen enzymatic fuel cells based on gold nanoparticle-modified electrodes.

We report on the fabrication and characterisation of a gold-nanoparticle (AuNP)-based mediatorless sugar/oxygen biofuel cell (BFC) operating in neutral sugar-containing buffers and human physiological fluids, such as blood and plasma. First, Corynascus thermophilus cellobiose dehydrogenase (CtCDH) and Myrothecium verrucaria bilirubin oxidase (MvBOx), used as anodic and cathodic bioelements, respectively, were immobilised on gold electrodes modified with 20 nm AuNPs. Detailed characterisation and optimisation of a new CDH/AuNP-based bioanode were performed and the following fundamental parameters were obtained: (i) the redox potential of the haem-containing centre of the enzyme was measured to be 75 mV vs. NHE, (ii) the surface coverage of CtCDH was found to be 0.65 pmol cm(-2) corresponding to a sub-monolayer coverage of the thiol-modified AuNPs by the enzyme, (iii) a turnover number for CtCDH immobilised on thiol-modified AuNPs was calculated to be ca. 0.5 s(-1), and (iv) the maximal current densities as high as 40 μA cm(-2) were registered in sugar-containing neutral buffers. Second, both biomodified electrodes, namely the CtCDH/AuNP-based bioanode and the MvBOx/AuNP-based biocathode, were combined into a functional BFC and the designed biodevices were carefully investigated. The following characteristics of the mediator-, separator- and membrane-less, miniature BFC were obtained: in phosphate buffer; an open-circuit voltage of 0.68 V, a maximum power density of 15 μW cm(-2) at a cell voltage of 0.52 V and in human blood; an open-circuit voltage of 0.65 V, a maximum power density of 3 μW cm(-2) at a cell voltage of 0.45 V, respectively. The estimated half-lives of the biodevices were found to be >12, <8, and <2 h in a sugar-containing buffer, human plasma, and blood, respectively. The basic characteristics of mediatorless sugar/oxygen BFCs were significantly improved compared with previously designed biodevices, because of the usage of three-dimensional AuNP-modified electrodes.

Biofuel cell as a power source for electronic contact lenses.

Here we present unequivocal experimental proof that microscale cofactor- and membrane-less, direct electron transfer based enzymatic fuel cells do produce significant amounts of electrical energy in human lachrymal liquid (tears). 100 μm diameter gold wires, covered with 17 nm gold nanoparticles, were used to fashion three-dimensional nanostructured microelectrodes, which were biomodified with Corynascus thermophilus cellobiose dehydrogenase and Myrothecium verrucaria bilirubin oxidase as anodic and cathodic bioelements, respectively. The following characteristics of miniature glucose/oxygen biodevices operating in human tears were registered: 0.57 V open-circuit voltage, about 1 μW cm(-2) maximum power density at a cell voltage of 0.5 V, and more than 20 h operational half-life. Theoretical calculations regarding the maximum recoverable electrical energy can be extracted from the biofuel and the biooxidant, glucose and molecular oxygen, each readily available in human lachrymal liquid, fully support our belief that biofuel cells can be used as electrical power sources for so called smart contact lenses.

Laccase electrode for direct electrocatalytic reduction of O2 to H2O with high-operational stability and resistance to chloride inhibition

Laccase from Trametes hirsuta basidiomycete has been covalently bound to graphite electrodes electrochemically modified with phenyl derivatives as a way to attach the enzyme molecules with an adequate orientation for direct electron transfer (DET). Current densities up to 0.5mA/cm(2) of electrocatalytic reduction of O(2) to H(2)O were obtained in absence of redox mediators, suggesting preferential orientation of the T1 Cu centre of the laccase towards the electrode. The covalent attachment of the laccase molecules to the functionalized electrodes permitted remarkable operational stability. Moreover, O(2) bioelectroreduction based on DET between the laccase and the electrode was not inhibited by chloride ions, whereas mediated bioelectrocatalysis was. In contrast, fluoride ions inhibited both direct and mediated electron transfers-based bioelectrocatalytic reduction of O(2). Thus, two different modes of laccase inhibition by halides are discussed.

Laccase-catalyzed synthesis of conducting polyaniline

Laccase isolated from Coriolus hirsutus was first used in the synthesis of water-soluble conducting polyaniline. The laccase-catalyzed polymerization of aniline was performed in the presence of sulfonated polystyrene (SPS) as a template. Laccase shows remarkable advantages in the synthesis of conducting polyaniline compared to the commonly used horseradish peroxidase due to its high activity and stability under acidic conditions. The characterization of the polyelectrolyte complex of polyaniline and SPS has been carried out using UV-Vis and FTIR spectroscopy. Cyclic voltammetry and dc conductivity measurements confirmed that electroactive polyaniline was synthesized by the laccase-catalyzed polymerization of aniline.

Gold Nanoparticles as Electronic Bridges for Laccase-Based Biocathodes

Direct electron transfer (DET) reactions between redox enzymes and electrodes can be maximized by oriented immobilization of the enzyme molecules onto an electroactive surface modified with functionalized gold nanoparticles (AuNPs). Here, we present such strategy for obtaining a DET-based laccase (Lc) cathode for O(2) electroreduction at low overpotentials. The stable nanostructured enzymatic electrode is based on the step-by-step covalent attachment of AuNPs and Lc molecules to porous graphite electrodes using the diazonium salt reduction strategy. Oriented immobilization of the enzyme molecules on adequately functionalized AuNPs allows establishing very fast DET with the electrode via their Cu T1 site. The measured electrocatalytic waves of O(2) reduction can be deconvoluted into two contributions. The one at lower overpotentials corresponds to immobilized Lc molecules that are efficiently wired by the AuNPs with a heterogeneous electron transfer rate constant k(0) ≫ 400 s(-1).

Direct electron transfer from graphite and functionalized gold electrodes to T1 and T2/T3 copper centers of bilirubin oxidase.

Direct electron transfer (DET) from bare spectrographic graphite (SPGE) or 3-mercaptopropionic acid-modified gold (MPA-gold) electrodes to Trachyderma tsunodae bilirubin oxidase (BOD) was studied under anaerobic and aerobic conditions by cyclic voltammetry and chronoamperometry. On cyclic voltammograms nonturnover Faradaic signals with midpoint potentials of about 700 mV and 400 mV were clearly observed corresponding to redox transformations of the T1 site and the T2/T3 cluster of the enzyme, respectively. The immobilized BOD was differently oriented on the two electrodes and its catalysis of O(2)-electroreduction was also massively different. On SPGE, where most of the enzyme was oriented with the T1 copper site proximal to the carbon with a quite slow ET process, well-pronounced DET-bioelectroreduction of O(2) was observed, starting already at >700 mV vs. NHE. In contrast, on MPA-gold most of the enzyme was oriented with its T2/T3 copper cluster proximal to the metal. Indeed, there was little DET-based catalysis of O(2)-electroreduction, even though the ET between the MPA-gold and the T2/T3 copper cluster of BOD was similar to that observed for the T1 site at SPGE. When BOD actively catalyzes the O(2)-electroreduction, the redox potential of its T1 site is 690 mV vs. NHE and that of one of its T2/T3 copper centers is 390 mV vs. NHE. The redox potential of the T2/T3 copper cluster of a resting form of BOD is suggested to be about 360 mV vs. NHE. These values, combined with the observed biocatalytic behavior, strongly suggest an uphill intra-molecular electron transfer from the T1 site to the T2/T3 cluster during the catalytic turnover of the enzyme.

A membrane-, mediator-, cofactor-less glucose/oxygen biofuel cell

We report the fabrication and characterisation of a non-compartmentalised, mediator and cofactor free glucose-oxygen biofuel cell based on adsorbed enzymes exhibiting direct bioelectrocatalysis, viz. cellobiose dehydrogenase from Dichomera saubinetii and laccase from Trametes hirsuta as the anodic and cathodic bioelements, respectively, with the following characteristics: an open-circuit voltage of 0.73 V; a maximum power density of 5 microW cm(-2) at 0.5 V of the cell voltage and an estimated half-life of > 38 h in air-saturated 0.1 M citrate-phosphate buffer, pH 4.5 containing 5 mM glucose.

Self-powered wireless carbohydrate/oxygen sensitive biodevice based on radio signal transmission

Here for the first time, we detail self-contained (wireless and self-powered) biodevices with wireless signal transmission. Specifically, we demonstrate the operation of self-sustained carbohydrate and oxygen sensitive biodevices, consisting of a wireless electronic unit, radio transmitter and separate sensing bioelectrodes, supplied with electrical energy from a combined multi-enzyme fuel cell generating sufficient current at required voltage to power the electronics. A carbohydrate/oxygen enzymatic fuel cell was assembled by comparing the performance of a range of different bioelectrodes followed by selection of the most suitable, stable combination. Carbohydrates (viz. lactose for the demonstration) and oxygen were also chosen as bioanalytes, being important biomarkers, to demonstrate the operation of the self-contained biosensing device, employing enzyme-modified bioelectrodes to enable the actual sensing. A wireless electronic unit, consisting of a micropotentiostat, an energy harvesting module (voltage amplifier together with a capacitor), and a radio microchip, were designed to enable the biofuel cell to be used as a power supply for managing the sensing devices and for wireless data transmission. The electronic system used required current and voltages greater than 44 µA and 0.57 V, respectively to operate; which the biofuel cell was capable of providing, when placed in a carbohydrate and oxygen containing buffer. In addition, a USB based receiver and computer software were employed for proof-of concept tests of the developed biodevices. Operation of bench-top prototypes was demonstrated in buffers containing different concentrations of the analytes, showcasing that the variation in response of both carbohydrate and oxygen biosensors could be monitored wirelessly in real-time as analyte concentrations in buffers were changed, using only an enzymatic fuel cell as a power supply.

Miniature Biofuel Cell as a Potential Power Source for Glucose-Sensing Contact Lenses

A microscale membrane-less biofuel cell, capable of generating electrical energy from human lachrymal liquid, was developed by utilizing the ascorbate and oxygen naturally present in tears as fuel and oxidant. The biodevice is based on three-dimensional nanostructured gold electrodes covered with abiotic (conductive organic complex) and biological (redox enzyme) materials functioning as efficient anodic and cathodic catalysts, respectively. Three-dimensional nanostructured electrodes were fabricated by modifying 100 μm gold wires with 17 nm gold nanoparticles, which were further modified with tetrathiafulvalene-tetracyanoquinodimethane conducting complex to create the anode and with Myrothecium verrucaria bilirubin oxidase to create the biocathode. When operated in human tears, the biodevice exhibited the following characteristics: an open circuit voltage of 0.54 V, a maximal power density of 3.1 μW cm(-2) at 0.25 V and 0.72 μW cm(-2) at 0.4 V, with a stable current density output of over 0.55 μA cm(-2) at 0.4 V for 6 h of continuous operation. These findings support our proposition that an ascorbate/oxygen biofuel cell could be a suitable power source for glucose-sensing contact lenses to be used for continuous health monitoring by diabetes patients.