Silvia Mosca

Assessment of nitrous oxide emission from cement plants: Real data measured with both Fourier transform infrared and nondispersive infrared techniques

Nitrous oxide (N2O) is the third most important greenhouse gas after carbon dioxide and methane, and contributes about 6% to the greenhouse effect. Nitrous oxide is a minor component of the atmosphere, and it is a thousand times less than carbon dioxide (CO2). Nevertheless, it is much more potent than CO2 and methane, owing to its long stay in the atmosphere of approximately 120 yr and the high global warming potential (GWP) of 298 times that of CO2. Although greenhouse gases are natural in the atmosphere, human activities have changed the atmospheric concentrations. Most of the values of emission of nitrous oxide are still obtained by means of emission factors and not actually measured; the lack of real data may result in an underestimation of current emissions. The emission factors used for the calculation of N2O can be obtained from the “Guidelines for the implementation of the national inventory of emissions” of the Intergovernmental Panel on Climate Change, which refer to all nations for the realization of their inventory. This study will present real data, measured in several Italian cement plants with different characteristics. The work also shows a comparison between N2O concentration measured with in situ Fourier transform IR (FTIR) and the reference method EN ISO 21258 based on nondispersive IR (NDIR), in order to investigate the interfering compounds in the measurement with NDIR. Implications: N2O may arise as an unwanted by-product of nitrogen oxide (NOx) abatement systems, in particular selective noncatalytic reduction (SNCR). Since it is applied in the cement plants, N2O emission from cement industry is evaluated, with both FTIR and NDIR instrument. Several considerations emerged from the results. First of all, the emission from this industrial sector is not negligible, and for that reason N2O concentration should be regulated; another observation is that the reference method based on the NDIR technique is not as selective as FTIR could be.

Evaluation of a simultaneous sampling method of PAHs, PCDD/Fs and dl-PCBs in ambient air

The Stockholm Convention on Persistent Organic Pollutants (POPs) was signed in May 2001 by 127 countries. Currently, 12 substances are regulated by the convention, and the work on finding new candidate chemicals to the convention has started. Among these 12 substances, dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polychlorinated biphenyls (PCBs) are the objects of this study. There are no European standard methods for the simultaneous determination of these microorganic compounds, together with polycyclic aromatic hydrocarbons (PAHs) in ambient air--they must be referred to three different methods developed by the U.S. Environmental Protection Agency (EPA). The quali-quantitative analysis of these microorganic pollutants is an important challenge due to the low concentrations at which they may be present. In this study, the development of a simplified, alternative, fast and affordable sampling method for the determination of PAHs, PCDDs, PCDFs and PCBs in ambient air was performed. The sampling time was extended from 24 h to 7 d in order to enrich the sample, to fall within the instrumental limits of detection and to reduce the number of samples to be processed and, therefore, errors that may arise. First of all, experiments with labelled standards were conducted in the research area of Montelibretti (rural station, which is sited about 20 km northeast of Rome), with the purpose of optimizing sampling efficiency. Finally, the method was applied to the analysis of these compounds in the air of a suburban area with small industrial plants in order to evaluate the feasibility of the proposed sampling method system, by comparing concentrations of native compounds acquired during simultaneous daily and weekly sampling.

Emission of submicron aerosol particles in cement kilns: Total concentration and size distribution

Cement plants are responsible for particle and gaseous emissions into the atmosphere. With respect to particle emission, the greater part of is in the range from 0.05 to 5.0 µm in diameter. In the last years attention was paid to submicron particles, but there is a lack of available data on the emission from stationary sources. In this paper, concentration and size distribution of particles emitted from four cement kilns, in relationship to operational conditions (especially the use of alternative fuel to coal) of the clinker process are reported. Experimental campaigns were carried out by measuring particles concentration and size distribution at the stack of four cement plants through condensation particle counter (CPC) and scanning mobility particle sizer spectrometer (SMPS). Average total particle number concentrations were between 2000 and 4000 particles/cm3, about 8–10 times lower that those found in the corresponding surrounding areas. As for size distribution, for all the investigated plants it is stable with a unimodal distribution (120–150 nm), independent from the fuel used. Implications: The study provides information on submicron particles emitted from cement kilns in different driving conditions. In particular, the total particle number is modest and considerably lower than that measured in ambient air, whereas the particle size distribution could be influenced by the operational conditions.