Sonja Schreurs

Characterisation of adsorbents prepared by pyrolysis of sludge and sludge/disposal filter cake mix

Copper and zinc removal from water (pH = 5.0) using adsorbents produced from slow and fast pyrolysis of industrial sludge and industrial sludge mixed with a disposal filter cake (FC), post treated with HCl, is investigated in comparison with a commercial adsorbent F400. The results show that a pseudo-second order kinetics model is followed. The Langmuir-Freundlich isotherm model is found to fit the data best. The capacity for heavy metal removal of studied adsorbents is generally better than that of commercial F400. The dominant heavy metal removal mechanism is cation exchange. Higher heavy metal removal capacity is associated with fast pyrolysis adsorbents and sludge/FC derived adsorbents, due to enhanced cation exchange. Improvement of Zn(2+) removal via 1 N HCl post-treatment is only effective when exchangeable cations of the adsorbent are substituted with H(+) ions, which boost the cation exchange capacity. Increase of temperature also enhances metal removal capacity. Fast pyrolysis sludge-based adsorbents can be reused after several adsorption-desorption cycles.

Economic assessment of flash co-pyrolysis of short rotation coppice and biopolymer waste streams.

The disposal problem associated with phytoextraction of farmland polluted with heavy metals by means of willow requires a biomass conversion technique which meets both ecological and economical needs. Combustion and gasification of willow require special and costly flue gas treatment to avoid re-emission of the metals in the atmosphere, whereas flash pyrolysis mainly results in the production of (almost) metal free bio-oil with a relatively high water content. Flash co-pyrolysis of biomass and waste of biopolymers synergistically improves the characteristics of the pyrolysis process: e.g. reduction of the water content of the bio-oil, more bio-oil and less char production and an increase of the HHV of the oil. This research paper investigates the economic consequences of the synergistic effects of flash co-pyrolysis of 1:1 w/w ratio blends of willow and different biopolymer waste streams via cost-benefit analysis and Monte Carlo simulations taking into account uncertainties. In all cases economic opportunities of flash co-pyrolysis of biomass with biopolymer waste are improved compared to flash pyrolysis of pure willow. Of all the biopolymers under investigation, polyhydroxybutyrate (PHB) is the most promising, followed by Eastar, Biopearls, potato starch, polylactic acid (PLA), corn starch and Solanyl in order of decreasing profits. Taking into account uncertainties, flash co-pyrolysis is expected to be cheaper than composting biopolymer waste streams, except for corn starch. If uncertainty increases, composting also becomes more interesting than flash co-pyrolysis for waste of Solanyl. If the investment expenditure is 15% higher in practice than estimated, the preference for flash co-pyrolysis compared to composting biopolymer waste becomes less clear. Only when the system of green current certificates is dismissed, composting clearly is a much cheaper processing technique for disposing of biopolymer waste.

Implementation of alanine/EPR as transfer dosimetry system in a radiotherapy audit programme in Belgium

A measurement procedure based on alanine/electron paramagnetic resonance (EPR) dosimetry was implemented successfully providing simple, stable, and accurate dose-to-water (D(w)) measurements. The correspondence between alanine and ionization chamber measurements in reference conditions was excellent. Alanine/EMR dosimetry might be a valuable alternative to thermoluminescent (TLD) and ionization chamber based measuring procedures in radiotherapy audits.

Study of the pyrolysis of sludge and sludge/disposal filter cake mix for the production of value added products

Slow and fast pyrolysis of sludge and sludge/disposal filter cake (FC) mix are performed to investigate the liquid and solid products for their use as value added products. The obtained slow pyrolysis liquid products separate in an oil, a water rich fraction and a valuable crystalline solid 5,5-dimethyl hydantoin. During fast pyrolysis, mainly an oil fraction is formed. Aliphatic acids and amides present in the water rich fractions can be considered as value added products and could be purified. The oil fractions have properties which make them promising as fuel (25-35 MJ/kg, 14-20 wt% water content, 0.2-0.6 O/C value), but upgrading is necessary. Sludge/FC oils have a lower calorific value, due to evaporation of alcohols present in FC. ICP-AES analyses reveal that almost none of the metals present in sludge or sludge/FC are transferred towards the liquid fractions. The metals are enriched in the solid fractions.

Activated carbon from pyrolysis of brewer’s spent grain: Production and adsorption properties:

Brewer’s spent grain is a low cost residue generated by the brewing industry. Its chemical composition (high nitrogen content 4.35 wt.%, fibres, etc.) makes it very useful for the production of added value in situ nitrogenised activated carbon. The composition of brewer’s spent grain revealed high amounts of cellulose (20.8 wt.%), hemicellulose (48.78 wt.%) and lignin (11.3 wt.%). The fat, ethanol extractives and ash accounted for 8.17 wt.%, 4.7 wt.% and 3.2 wt.%, respectively. Different activated carbons were produced in a lab-scale pyrolysis/activation reactor by applying several heat and steam activation profiles on brewer’s spent grain. Activated carbon yields from 16.1 to 23.6 wt.% with high N-contents (> 2 wt.%) were obtained. The efficiency of the prepared activated carbons for phenol adsorption was studied as a function of different parameters: pH, contact time and carbon dosage relative to two commercial activated carbons. The equilibrium isotherms were described by the non-linear Langmuir and Freundlich models, and the kinetic results were fitted using the pseudo-first-order model and the pseudo-second-order model. The feasibility of an activated carbon production facility (onsite and offsite) that processes brewer’s spent grain for different input feeds is evaluated based on a techno-economic model for estimating the net present value. Even though the model assumptions start from a rather pessimistic scenario, encouraging results for a profitable production of activated carbon using brewer’s spent grain are obtained.

Rapeseed and Raspberry Seed Cakes as Inexpensive Raw Materials in the Production of Activated Carbon by Physical Activation: Effect of Activation Conditions on Textural and Phenol Adsorption Characteristics

The production of activated carbons (ACs) from rapeseed cake and raspberry seed cake using slow pyrolysis followed by physical activation of the obtained solid residues is the topic of this study. The effect of activation temperature (850, 900 and 950 °C), activation time (30, 60, 90 and 120 min) and agent (steam and CO2) on the textural characteristics of the ACs is investigated by N2 adsorption. In general, higher activation temperatures and longer activation times increase the BET specific surface area and the porosity of the ACs, regardless of the activation agent or raw material. Steam is more reactive than CO2 in terms of pore development, especially in the case of raspberry seed cake. The performance of the ACs in liquid adsorption is evaluated by batch phenol adsorption tests. Experimental data are best fitted by the Freundlich isotherm model. Based on total yield, textural characteristics and phenol adsorption, steam activation at 900 °C for 90 min and CO2 activation at 900 °C for 120 min are found as the best activation conditions. Raspberry seed cake turns out to be a better raw material than rapeseed cake. Moreover, AC from raspberry seed cake produced by steam activation at 900 °C for 90 min performs as well as commercial AC (Norit GAC 1240) in phenol adsorption. The adsorption kinetics of the selected ACs are best fitted by the pseudo-second-order model.

From raw materials to NORM by-products

Abstract Naturally occurring radionuclides are present in the Earth crust; however, their distribution is not homogeneous. When primary or secondary raw materials containing relatively low concentrations of naturally occurring radionuclides are introduced in an industrial process then the radionuclides can become more concentrated in the produced (by-)products. For example, during the production of purified metals, throughout the purification process, also other elements, such as naturally occurring radionuclides, become concentrated in the by-products. In order to assure radiation protection of the population, it is important to map the potential exposure for workers and the general public. There is an extensive literature available regarding the presence of naturally occurring radionuclides in various by-products; however, it can be hard to review and even to interpret for the regulators and members of the industry in order to assure the safe use of by-products for example in construction. To solve this problem data mining and text processing have been applied to the ever-increasing numbers of publications (More than 39,000 filtered publications have been processed up to the Jan. 6, 2017), and the NORM4Building database has been compiled based on the analysis of the collected data. Based on this database using text analysis methods the most NORM prone raw materials and industries have been identified. This chapter gives a concise overview on the parameters to be considered during the selection of NORM by-products as feedstock for the construction industry, specifically for the production of cement, concrete, and ceramics. In the frame of this chapter the technical and radiological properties of the most representative industrial processes (such as coal mining and combustion; iron and steel production; the alumina, the zirconia, and the phosphate industry; etc.) and their by-products are discussed, especially considering the needs of the construction industry and the new European Basic Safety Standards.

The combined use of the improved methods of Gardner and Prony for the qualitative and quantitative analysis of multicomponent decay curves

Abstract Two complementary methods, the improved method of Gardner et al. and of Prony for the analysis of multicomponent decay curves, are presented. The improved method of Gardner et al. can be applied to determine the number of components and to estimate the decay constants. These can then be quantified together with the pre-exponential factors using the recurrence version of Pronys improved method. Computer implementations of these methods are described. Their performance is evaluated on simulated decay curves in the absence and presence of Poisson distributed noise, as well as on experimental decay curves obtained from fluorescence, solid state free induction decay ( 1 H NMR), and radioactivity measurements. Guidelines for experiments are formulated in order to obtain the best results in the sequential data analyses.

Combining Monte Carlo simulations and experimental design for incorporating risk and uncertainty in investment decisions for cleantech: a fast pyrolysis case study

The value of phytoextracting crops (plants cultivated for soil remediation) depends on the profitability of the sequential investment in a conversion technology aimed at the economic valorization of the plants. However, the net present value (NPV) of an investment in such an innovative technology is risky due to technical and economic uncertainties. Therefore, decision makers want to dispose of information about the probability of a positive NPV, the largest possible loss, and the crucial economic and technical parameters influencing the NPV. This paper maps the total uncertainty in the NPV of an investment in fast pyrolysis for the production of combined heat and power from willow cultivated for phytoextraction in the Belgian Campine. The probability of a positive NPV has been calculated by performing Monte Carlo simulations. Information about possible losses has been provided by means of experimental design. Both methods are then combined in order to identify the key economic and technical parameters influencing the project’s profitability. It appears that the case study has a chance of 87% of generating a positive NPV with an expected value of 3 million euro (MEUR), while worst-case scenarios predict possible losses of 7 MEUR. The amount of arable land, the biomass yield, the purchase price of the crop, the policy support, and the product yield of fast pyrolysis are identified as the most influential parameters. It is concluded that both methods, i.e., Monte Carlo simulations and experimental design, provide decision makers with complementary information with regard to economic risk.

Enhanced cesium removal from real matrices by nickel-hexacyanoferrate modified activated carbons

After nuclear disasters, radioactive cesium partitions to soils and surface water, where it decays slowly. Hexacyanoferrates (HCFs) have excellent cesium removal properties but their structure is typically powdery. Many carrier materials, such as biomass or magnetic particles, have been used to provide a suitable substrate for HCFs that can be used in filters. This research uses the sorption properties of activated carbon (AC) to incorporate Ni-HCF, resulting in good structural properties of the hybrid material. These HCF-modified ACs show drastically improved sorption properties towards Cs after one, two and three HCF impregnation cycles. The activated carbon from brewers spent grain with one modification cycle removes more than 80% of 1 mg L-1 Cs in a sea water solution and more than 98% of 1 mg L-1 Cs from surface water at a low AC dosage (0.5 g L-1). Iron and nickel leaching is studied and found to be dependent on the type of modified AC used and the leaching solution. Iron leaching can be problematic in surface and seawater, whereas nickel leaching is especially pronounced in seawater.