Soo-Ahn Kwon

Development of Warm-Mix Asphalt Additive and Evaluation of Performance

Several warm-mix asphalt (WMA) technologies have been developed and implemented worldwide. Because of the reduced production and compaction temperatures of WMA mixtures, WMA technology can reduce energy consumption, carbon dioxide emission, and asphalt oxidation as well as extend the paving season, increase hauling distance, and create a better working environment. A wax-based WMA additive called low-energy and low–carbon-dioxide asphalt pavement (LEADCAP), has been developed by the Korea Institute of Construction Technology and Kumho Petrochemical and is the first WMA additive developed in South Korea. This paper introduces the characteristics of this newly developed WMA additive and presents the performance evaluation of WMA with LEADCAP. To evaluate the performance of the WMA mixture with LEADCAP additive, the Superpave® mix design, moisture susceptibility test, and mechanical test were performed. Common hot-mix asphalt and a WMA mixture with Sasobit additive were also evaluated for comparison. Sasobit is also a wax-based additive and is well-known. Mechanical tests included the dynamic modulus test, the direct tension fatigue test, and the triaxial repeated loading permanent deformation test. From the limited data obtained in this study, it was concluded that LEADCAP could be effectively used in WMA mixtures and that the performance of WMA with LEADCAP could be expected to be comparable to that of hot-mix asphalt and WMA with Sasobit additive.

Noise Evaluation of the Rumble Strips Constructed at Tall Gate of Highway

PURPOSES: This study evaluated a measuring technique for tire-pavement interaction noise that uses a noble close proximity (NCPX) method as well as for noise level measured inside of a car (e.g., Inside Noise Level) in term of rumble strips constructed at a tall gate. METHODS: According to the measurements of NCPX and inside noise level (INL), 1/3 octave band frequency analysis and overall noise level calculation were conducted in order to evaluate noise levels of NCPX and INL, depending on types of rumble strips. RESULTS: The tested sections of general concrete pavement surface and two different types of rumble strips were evaluated, using 1/3 octave band frequency analysis and overall noise level. From the analyzed results, it can be concluded that rumble strips generate a relatively huge noise levels when compared to the concrete pavement surface. CONCLUSIONS: Noting that above 3 dBA different noise levels can let drivers know that they are getting close to toll gate; therefore, they should apply their brakes. Thus, the noise levels of rumble strips are required to be reduced, based on considering the neighbors living near toll gates.

Study on the Functional Evaluation of Permeable Asphalt Concrete Pavement in Seoul City

The functional evaluation of constructed permeable pavements was conducted in terms of water permeable performance and noise reduction measurements in Seoul city. The field measurements of noise was based on two methods such as pass-by and novel close proximity(NCPX). The pass-by test and NCPX method are related to noise propagation and tire/pavement interaction noise measurement, respectively. For the water permeable tests, five sections were chosen; furthermore, the measurements were conducted for both of wheel path and non-wheel path area. For the pass-by measurement, three sections were chosen; furthermore, two different locations, which were near measurement point to traffic noise and far measurement point inside park or hosing complex, were selected for each section. Finally, tire/pavement interaction noise measurements were carried out at four locations. The results show that the functional performance of water permeability and noise reduction was well remained within 2 or 3 years after permeable pavement construction.

Variation of Image Analysis Results for Determining the Characteristics of the Air-Void System on Hardened Concrete

Recently, the cases of freeze-thaw distress on concrete pavement in domestic have been reported periodically. Hereupon, the necessity to establish the standard of spacing factor came to the fore. The test method for analyzing spacing factor is provided in the standard of ASTM C 457. Since researchers tend to judge study results subjectively, the results should be revised throughly. Image analysis program for determining the characteristics of air-void system on hardened concrete identify air void through the difference of a color. The pixel intensity values used in this program have a significant effect on the analysis results. This study compared the automated void count by varying pixel intensity values with the manual void count in order to determine the optimum range of pixel intensity values. Also, this study analyzed the air-void characteristics on eight kinds of concrete mixtures. In this study, it was confirmed that the variation of void counted manually was around 10% from the results of round robin test, and that the optimum range of pixel intensity values is around 80~90. And it was also confirmed that air content (as a whole) was increased generally and spacing factor was decreased by increasing air-entrainer content. But some concrete mixtures showed a tendency that air content was constant and spacing factor was decreased by increasing air-entrainer content. This causes the air entrained by air-entrainer has more influence on spacing factor than air content. Also, the deviation of spacing factor by cutting position of concrete specimen was about 30~100 because of the limit of 2-D image analysis. The additional study about variation of spacing factor by cutting position of concrete specimen will be performed later.

Estimation of Performance and Pavement Life using National Highway Pavement Condition Index

PURPOSES: The new methodology is proposed for estimation of long-term performance and pavement life based on the national highway database in Daejeon area. Furthermore, this study tried to verify the applicability of performance estimation using NHPCI (National Highway Pavement Condition Index) on tendency of pavement deterioration as time goes by under Korean road environments. METHODS: Reliability theories are applied to estimate the mean life and to determine the appropriate distribution using 3 levels of traffic loads (high, medium, low) based on maintenance and rehabilitation history data for 15 years. RESULTS: As a result, Lognormal distribution is suitable for explanation of pavement lifetime in Daejeon area regardless of traffic loads. In addition, we found that the results of mean life and maintenance timing based on NHPCI for the pavement sections of 3 levels of traffic loads are available. CONCLUSIONS: Based on this study, it was found that mean life of high, medium and low levels of traffic loads are about 8.1 years, 12.2 years and 12.7 years, respectively. Higher level of traffic loads shorten the pavement mean life.

Evaluation of Rutting Resistance and Moisture Sensitivity of Warm-Mix Asphalt Mixtures Using the Model Mobile Loading Simulator(MMLS3)

Warm-mix asphalt(WMA) technology has been developed to allow asphalt mixtures to be produced and compacted at a significantly lower temperature. The WMA technology was identified as one of means to lower emissions for and has been spread so quickly in the world. Recently, two innovative WMA additives has been developed to reduce mixing and paving temperatures applied in asphalt paving process in Korea. Since the first public demonstration project in 2008, many WMA projects have successfully been constructed in national highways. In 2010, the WMA field trial was conducted on new national highway construction under Dae-Jeon Regional Construction Management Administration. The two different WMA loose mixtures(WMA and WMA-P) and a HMA mixture were collected at the asphalt plant to evaluate their mechanical performance in the laboratory. The Third-scale Model Mobile Loading Simulator(MMLS3) was adopted to evaluate rutting resistance and moisture damage under different traffic and environmental conditions. In this study, plant-produced WMA mixtures using two WMA additives along with the conventional hot mix asphalt(HMA) mixtures were evaluated with respect to their rutting resistance and moisture susceptibility using MMLS3. Based on the limited laboratory test results, plant-produced WMA mixtures are superior to HMA mixtures in rutting resistance and the moisture susceptibility. The WMA additive was effective for producing and compacting the mixture at lower than the temperature for the HMA mixture.

A Experimental Study on Application of KS F 2456 using Shear Wave

PURPOSES: It is important to consider the long-term performance of concrete pavement, because concrete pavement is more exposed to the various environmental conditions than any other concrete structures. One of the several methods to evaluate the long-term performance of concrete during winter is KS F 2456. Relative dynamic modulus of elasticity shows the resistance to freezing and thawing. METHODS: To measure relative dynamic modulus of elasticity, ultra sonic is generally used. But in this study, to measure the relative dynamic modulus of elasticity, both ultra sonic and shear wave were used and then compared each other. RESULTS: The results from the measurement by ultrasonic wave and shear wave were divided into three types. Type 1 : Specimens are good and relative dynamic modulus of elasticity did not decrease until 300 cycle. Type 2 : The relative dynamic modulus of elasticity decreased from the late cycle.(about 150 cycle later) Type 3 : The relative dynamic modulus of elasticity consistently decreased from the beginning. As a result of ANOVA, there is no difference according to measuring method, in type 2 and 3. But there is a difference according to measuring method, in type 1`s relative dynamic modulus of elasticity. CONCLUSIONS: It is proved that shear wave can be used to understand the damage tendency of relative freezing and thawing and to measure the relative dynamic modulus of elasticity.

An Analytical Study to Reduce Plastic Deformation in Intersection Pavements

PURPOSES : Plastic deformation is frequently made in intersection asphalt pavement at its early age due to deceleration and stoppage of vehicles. This study has been performed to provide a mechanistic basis for reasonable selection of paving method to minimize the plastic deformation at intersection. METHODS : Pavement layer, temperature, traffic volume of the intersections managed by the Daejeon Regional Construction and Management Administration were collected to calculate asphalt dynamic modulus with pavement depth by using a prediction equation suggested by the Korean pavement design guide. Performance of ordinary dense-graded asphalt pavement, polymer modified asphalt pavement, and fiber reinforced asphalt pavement was analyzed by finite element method and the results were used in a performance model to predict the plastic deformation. RESULTS : In aspect of performance, the three paving methods were usable under low traffic while the fiber reinforced asphalt pavement was the most suitable under heavy traffic. CONCLUSIONS : Reasonable paving method suitable for traffic characteristics in the intersection might be decided by considering economic feasibility.

Feasibility Evaluation of Number of Gyration for HMA and WMA Mixtures

The objective of this study is to validate the number of gyrations of Superpave gyratory compactor(SGC) for compaction of hot-mix asphalt (HMA) and warm-mix asphalt(WMA) mixtures. Marshall compaction was also used for comparison purpose. The 13mm and 19mm aggregates of 1st class quality shape were used. A PG64-22 and a PG76-22 for HMA and a PG70-22 for WMA. Four compaction temperatures based on the suggested value were used for each binder using 100 gyrations for SGC and 75 blows per side for Marshall compactor. It was found that SGC compaction was somewhat better than Marshall compaction. The analysis of variance showed that two compactors were significantly different in air voids of 19mm mixtures at

A Study of Performance Evaluation of Warm Asphalt Binder Properties using LEADCAP (R) additive

{\alpha}