Soumya Pandit

Graphene supported α-MnO2 nanotubes as a cathode catalyst for improved power generation and wastewater treatment in single-chambered microbial fuel cells

Microbial fuel cells (MFC) are a promising system to simultaneously accomplish the goal of energy production and wastewater treatment. In the MFC, the cathode plays an important role in achieving high power density and thereby improving the cell performance. In the cathode, an allotrope of carbon [activated carbon, graphite, multi-walled carbon nanotubes (MWCNTs)] is commonly used as a support material for catalysts, such as Pt. Here we show the improved performance of single-chambered MFC (sMFC) using hydrothermally synthesized α-manganese dioxide nanotubes (MnO2-NTs) as the catalyst and graphene as the support in the cathode. With a fixed MnO2-NTs loading, a maximum volumetric power density of 4.68 W m−3 was achieved from the sMFC with MnO2-NTs/graphene, which is higher than that of MnO2-NTs/MWCNTs (3.94 W m−3) and MnO2-NTs/Vulcan XC (2.2 W m−3) composite cathodes, but marginally lower than that of the benchmark Pt/C cathode (5.67 W m−3). The MnO2-NTs/graphene composite also showed a higher oxygen reduction reaction (ORR) activity than the MnO2-NTs/MWCNTs and MnO2-NTs/Vulcan XC composites implying that the former is a better catalyst than the later two. This study demonstrates the high ORR activity and high power generation ability of the cost-effective MnO2-NTs/graphene composite and makes it a potential cathode material for the replacement of expensive Pt in constructing large-scale MFC for wastewater treatment and bioelectricity production.

Performance of electron acceptors in catholyte of a two-chambered microbial fuel cell using anion exchange membrane

The performance of the cathodic electron acceptors (CEA) used in the two-chambered microbial fuel cell (MFC) was in the following order: potassium permanganate (1.11V; 116.2 mW/m(2))>potassium persulfate (1.10 V; 101.7 mW/m(2))>potassium dichromate, K(2)Cr(2)O(7) (0.76 V; 45.9 mW/m(2))>potassium ferricyanide (0.78 V; 40.6 mW/m(2)). Different operational parameters were considered to find out the performance of the MFC like initial pH in aqueous solutions, concentrations of the electron acceptors, phosphate buffer and aeration. Potassium persulfate was found to be more suitable out of the four electron acceptors which had a higher open circuit potential (OCP) but sustained the voltage for a much longer period than permanganate. Chemical oxygen demand (COD) reduction of 59% was achieved using 10mM persulfate in a batch process. RALEX™ AEM-PES, an anion exchange membrane (AEM), performed better in terms of power density and OCP in comparison to Nafion®117 Cation Exchange Membrane (CEM).

Manganese cobaltite/polypyrrole nanocomposite-based air-cathode for sustainable power generation in the single-chambered microbial fuel cells

Manganese cobaltite nanorods (MnCo2O4 NRs) were prepared and tested as potential air-cathode catalyst for the single-chambered microbial fuel cells (sMFC). The power generation of sMFC increases with MnCo2O4 NRs loading to the cathode. The Polypyrrole (PPy) and Vulcan XC were used as conducting support to the MnCo2O4 NRs to form composites either by in situ or by mechanical mixing in the cathode fabrication. The cyclic voltammetry, linear sweep voltammetry and electrochemical impedance studies reveal that the in situ-MnCo2O4 NRs/PPy composite has higher catalytic activity than that of mechanically mixed-MnCo2O4NRs/PPy composite because of higher interfacial contact between MnCo2O4 NRs and PPy. The maximum volumetric power density with in situ-MnCo2O4 NRs/PPy, mechanically mixed-MnCo2O4 NRs/PPy, MnCo2O4 NRs/Vulcan XC and catalyst-free (only Vulcan XC) cathode was measured to be 6.11, 5.05, 4.22, and 1.77 W/m(3), respectively, in the sMFC. This suggests that PPy is not only a better conducting support than that of conventionally used Vulcan XC but also the cathode composite fabrication process is important for enhanced performance. The synergetic effect of MnCo2O4 NRs and PPy was found to play an important role for the improved energy recovery and it could be applied as an efficient and inexpensive cathode catalyst for the sMFC.

Bifunctional Manganese Ferrite/Polyaniline Hybrid as Electrode Material for Enhanced Energy Recovery in Microbial Fuel Cell

Microbial fuel cells (MFCs) are emerging as a sustainable technology for waste to energy conversion where electrode materials play a vital role on its performance. Platinum (Pt) is the most common material used as cathode catalyst in the MFCs. However, the high cost and low earth abundance associated with Pt prompt the researcher to explore inexpensive catalysts. The present study demonstrates a noble metal-free MFC using a manganese ferrite (MnFe2O4)/polyaniline (PANI)-based electrode material. The MnFe2O4 nanoparticles (NPs) and MnFe2O4 NPs/PANI hybrid composite not only exhibited superior oxygen reduction reaction (ORR) activity for the air cathode but also enhanced anode half-cell potential upon modifying carbon cloth anode in the single-chambered MFC. This is attributed to the improved extracellular electron transfer of exoelectrogens due to Fe(3+) in MnFe2O4 and its capacitive nature. The present work demonstrates for the first time the dual property of MnFe2O4 NPs/PANI, i.e., as cathode catalyst and an anode modifier, thereby promising cost-effective MFCs for practical applications.

Microbial carbon capture cell using cyanobacteria for simultaneous power generation, carbon dioxide sequestration and wastewater treatment

Microbial carbon capture cells (MCCs) were constructed with cyanobacteria growing in a photo biocathode in dual-chambered flat plate mediator-less MFCs separated by an anion exchange membrane from the anode compartment containing Shewanella putrefaciens. The performance of the MCC with Anabaena sparged with CO(2)-air mixture was compared with that of a conventional cathode sparged with air only. The power densities achieved were 57.8 mW/m(2) for Anabaena sparged with a CO(2)-air mixture, 39.2 mW/m(2) for CO(2)-air mixture sparging only, 29.7 mW/m(2) for Anabaena sparged with air, and 19.6 mW/m(2) for air sparging only. The pH of the cathode containing Anabaena gradually increased from 7 to 9.12 and power generation decreased from 34.7 to 23.8 mW/m(2) 17 due to pH imbalance associated voltage losses without CO(2)-air mixture sparging. Sparging with a 5% CO(2)-air mixture produced maximum power of 100.1 mW/m(2). In addition, the power density of MCC increased by 31% when nitrate was added into the catholyte.

Improvement of power generation using Shewanella putrefaciens mediated bioanode in a single chambered microbial fuel cell: Effect of different anodic operating conditions

Three different approaches were employed to improve single chambered microbial fuel cell (sMFC) performance using Shewanella putrefaciens as biocatalyst. Taguchi design was used to identify the key process parameter (anolyte concentration, CaCl₂ and initial anolyte pH) for maximization of volumetric power. Supplementation of CaCl₂ was found most significant and maximum power density of 4.92 W/m(3) was achieved. In subsequent approaches, effect on power output by riboflavin supplementation to anolyte and anode surface modification using nano-hematite (Fe₂O₃) was observed. Volumetric power density was increased by 44% with addition of 100 nM riboflavin to anolyte while with 0.8 mg/cm(2) nano-Fe₂O₃ impregnated anode power density and columbic efficiency increased by 40% and 33% respectively. Cyclic voltammetry revealed improvement in electrochemical activity of Shewanella with nano-Fe₂O₃ loading and electrochemical impedance depicted inverse relationship between charge transfer resistance and nano-Fe₂O₃ loading. This study suggests anodic improvement strategies for maximization of power output.

Reduction of start-up time through bioaugmentation process in microbial fuel cells using an isolate from dark fermentative spent media fed anode

An electrochemically active bacteria Pseudomonas aeruginosa IIT BT SS1 was isolated from a dark fermentative spent media fed anode, and a bioaugmentation technique using the isolated strain was used to improve the start-up time of a microbial fuel cell (MFC). Higher volumetric current density and lower start-up time were observed with the augmented system MFC-PM (13.7 A/m(3)) when compared with mixed culture MFC-M (8.72 A/m(3)) during the initial phase. This enhanced performance in MFC-PM was possibly due to the improvement in electron transfer ability by the augmented strain. However, pure culture MFC-P showed maximum volumetric current density (17 A/m(3)) due to the inherent electrogenic properties of Pseudomonas sp. An electrochemical impedance spectroscopic (EIS) study, along with matrix-assisted laser desorption/ionization-time-of-flight (MALDI-TOF) analysis, supported the influence of isolated species in improving the MFC performance. The present study indicates that the bioaugmentation strategy using the isolated Pseudomonas sp. can be effectively utilized to decrease the start-up time of MFC.

Study of performance scaling of 22-nm epitaxial delta-doped channel MOS transistor

Epitaxial delta-doped channel (EδDC) profile is a promising approach for extending the scalability of bulk metal oxide semiconductor (MOS) technology for low-power system-on-chip applications. A comparative study between EδDC bulk MOS transistor with gate length Lg = 22 nm and a conventional uniformly doped channel (UDC) bulk MOS transistor, with respect to various digital and analogue performances, is presented. The study has been performed using Silvaco technology computer-aided design device simulator, calibrated with experimental results. This study reveals that at smaller gate length, EδDC transistor outperforms the UDC transistor with respect to various studied performances. The reduced contribution of the lateral electric field in the channel plays the key role in this regard. Further, the carrier mobility in EδDC transistor is higher compared to UDC transistor. For moderate gate and drain bias, the impact ionisation rate of the carriers for EδDC MOS transistor is lower than that of the UDC transistor. In addition, at 22 nm, the performances of a EδDC transistor are competitive to that of an ultra-thin body silicon-on-insulator transistor.

Modeling and design of a nano scale CMOS inverter for symmetric switching characteristics

This paper presents a technique for the modeling and design of a nano scale CMOS inverter circuit using artificial neural network and particle swarm optimization algorithm such that the switching characteristics of the circuit is symmetric, that is, has nearly equal rise and fall time and equal output high-to-low and low-to-high propagation delay. The channel width of the transistors and the load capacitor value are taken as design parameters. The designed circuit has been implemented at the transistor-level and simulated using TSPICE for 45 nm process technology. The PSO-generated results have been compared with SPICE results. A very good accuracy has been achieved. In addition, the advantage of the present approach over an existing approach for the same purpose has been demonstrated through simulation results.

Systematic Methodology for High-Level Performance Modeling of Analog Systems

This paper presents a systematic methodology for construction of high-level performance models using least squares support vector machine. The transistor sizes of the circuit-level implementation of a component block along with a set of geometry constraints applied over them define the sample space. Optimal values of the model hyper parameters are computed using genetic algorithm. The novelty of the methodology is that the models constructed with this methodology are accurate, fast to evaluate with good generalization ability and low construction time. The present methodology has been compared with two other standard methodologies and the novelties are clearly demonstrated with experimental results.