Stefan Spirk

In situ preparation of silver nanocomposites on cellulosic fibers – Microwave vs. conventional heating

A green approach for the preparation of silver nanocomposites on viscose fibers using microwave and conventional heating is presented. Reduction of silver nitrate is induced by addition of 6-O chitosan sulfate (S-Chi) in aqueous media which provides steric protection and electrostatic stabilization to prevent agglomeration of the nanoparticles. The particles are formed in close spatial proximity to the fibers and adsorption of the particles via structural similarity takes place to create silver nanocomposites. All nanocomposites have been subjected to antimicrobial tests and high antimicrobial activity toward Escherichia coli bacteria has been determined. Further, the nanocomposites are characterized using different analytical techniques which reveal very similar results for both heating techniques. The only significant difference is observed concerning the shape of the nanoparticles on the viscose fibers which are slightly elongated for the microwave method in comparison to spheres observed by conventional heating. Therefore, detailed investigations on the formation of colloidal silver nanoparticles have been performed, comparing microwave dielectric and conventional heating at the exact same temperature and reaction times. These experiments resulted in nearly identical nanoparticle shape and size for both heating methods as demonstrated by dynamic light scattering, UV-vis spectroscopy and transmission electron microscopy. A wide range of parameters has been varied (temperature, AgNO3 to S-Chi ratio, reaction time, and stirring speed) to study the nanoparticle formation under microwave and conventional conditions. No evidence for the existence of so-called specific microwave effects was obtained.

Exploring the rearrangement of amorphous cellulose model thin films upon heat treatment

The behavior of amorphous cellulose model thin films upon heat treatment is investigated. Upon heat treatment, a structural rearrangement in the films from a featureless to a fibrillar structure is observed which correlates with the regeneration time and total cellulose content as proven by atomic force microscopy and X-ray photoelectron spectroscopy. ATR-IR spectroscopy proves the presence of stronger hydrogen bonds in the heat treated surfaces which originate from a reorganization of the cellulose chains and pore structure. The rearrangement is accompanied with an increased surface hydrophobicity, a reduced swelling capacity and a reduction in the water content of the films. An increase in crystallinity of the films is not observed.

Chitosan–silane sol–gel hybrid thin films with controllable layer thickness and morphology

The preparation of thin films of chitosan-silane hybrid materials by combining sol-gel processing and spin coating is reported. A variety of silanes can be used as starting materials for the preparation of such thin films, namely tetraethoxysilane, tri-tert-butoxysilanol, trimethylethoxysilane, p-trifluoromethyltetra-fluorophenyltriethoxysilane, trivinylmethoxysilane, (methoxymethyl)trimethyl-silane, and hexamethoxydisilane. These silanes are subjected to a sol-gel process before they are added to acidic chitosan solutions. The chitosan:silane ratio is kept constant at 6:1 (w/w) and dilutions with ethanol are prepared and spin coated. Depending on the degree of dilution, film thickness can be controlled in a range between 5 and 70 nm. For the determination of additional surface properties, static water contact angle measurements and atomic force microscopy have been employed.

Green synthesis of the silver nanoparticles mediated by pullulan and 6-carboxypullulan

Unoxidized and carboxylated pullulan (obtained by pullulan oxidation using TEMPO-sodium hypochlorite-sodium bromide system) have been used as mediators for the silver nanoparticles formation (AgNPs), under environment-friendly conditions: using aqueous solutions, room temperature and notably, by using both mediators as reducing and stabilizing agents. The formation of AgNPs was first screened by measuring the surface plasmon resonance peak in the range of 380-440 nm using UV-vis spectroscopy. The morphology of the synthesized silver nanoparticles was determined by TEM, which indicated that the AgNPs differ on shape and thickness of the polymer shell by varying the silver nitrate concentration, different size and shape of AgNPs was achieved. The presence of elemental silver and the crystalline structure of the AgNPs were confirmed by EDX and XRD analyses. Moreover, the possible functional groups of pullulan (oxidized pullulan) responsible for the reduction and stabilization of AgNPs were evaluated using FT-IR. The results showed that both, pullulan and 6-carboxypullulan could be successfully used as reducing as well as capping agents for the AgNPs synthesis which shows potential antimicrobial activity against Gram positive and Gram negative bacteria.

Surface Modifications Using a Water-Stable Silanetriol in Neutral Aqueous Media

Surface modifications of glass slides employing the sterically hindered tert-butyl substituted silanetriol are described. To the best of our knowledge, this is the first time that a stable silanetriol has been directly used for this purpose. So far unprecedented, this process runs under neutral aqueous conditions and in the absence of organic solvents, which makes coating protocols accessible to acid-sensitive substrates. The layer thickness and surface topography are investigated by the Sarfus technique, by X-ray reflectivity, and by atomic force microscopy (AFM). These techniques yield values of 0.8±0.1 (XRR) and 0.6±0.2 nm (Sarfus) for layer thickness and 0.33 nm for root mean square roughness (AFM). The modified surfaces have hydrophobic and oleophilic character and contact angles (CA) between 60° (formamide, CH2I2) and 90° (water) are obtained. The thin coatings allow a structuring by UV/ozone treatment in order to get hydrophilic and hydrophobic compartments on the surfaces. For all coatings, surface free energies are calculated using different models. To determine the isoelectric points (IEP) of the modified surfaces, we performed zeta-potential measurements. Correlations between zeta potentials and hydrophilicity of the surfaces are shown.

Photolithographic patterning of cellulose: a versatile dual-tone photoresist for advanced applications.

In many areas of science and technology, patterned films and surfaces play a key role in engineering and development of advanced materials. Here, we present a versatile toolbox that provides an easy patterning method for cellulose thin films by means of photolithography and enzymatic digestion. A patterned UV-illumination of trimethylsilyl cellulose thin films containing small amounts of a photo acid generator leads to a desilylation reaction and thus to the formation of cellulose in the irradiated areas. Depending on the conditions of development, either negative and positive type cellulose structures can be obtained, offering lateral resolutions down to the single-digit micro meter range by means of contact photolithography. In order to highlight the potential of this material for advanced patterning techniques, cellulose structures with sub-µm resolution are fabricated by means of two-photon absorption lithography. Moreover, these photochemically structured cellulose thin films are successfully implemented as dielectric layers in prototype organic thin film transistors. Such photopatternable dielectric layers are crucial for the realization of electrical interconnects for demanding organic device architectures.

Triggering protein adsorption on tailored cationic cellulose surfaces.

The equipment of cellulose ultrathin films with BSA (bovine serum albumin) via cationization of the surface by tailor-made cationic celluloses is described. In this way, matrices for controlled protein deposition are created, whereas the extent of protein affinity to these surfaces is controlled by the charge density and solubility of the tailored cationic cellulose derivative. In order to understand the impact of the cationic cellulose derivatives on the protein affinity, their interaction capacity with fluorescently labeled BSA is investigated at different concentrations and pH values. The amount of deposited material is quantified using QCM-D (quartz crystal microbalance with dissipation monitoring, wet mass) and MP-SPR (multi-parameter surface plasmon resonance, dry mass), and the mass of coupled water is evaluated by combination of QCM-D and SPR data. It turns out that adsorption can be tuned over a wide range (0.6-3.9 mg dry mass m(-2)) depending on the used conditions for adsorption and the type of employed cationic cellulose. After evaluation of protein adsorption, patterned cellulose thin films have been prepared and the cationic celluloses were adsorbed in a similar fashion as in the QCM-D and SPR experiments. Onto these cationic surfaces, fluorescently labeled BSA in different concentrations is deposited by an automatized spotting apparatus and a correlation between the amount of the deposited protein and the fluorescence intensity is established.

Design of simultaneous antimicrobial and anticoagulant surfaces based on nanoparticles and polysaccharides

The rational design of silver nanoparticles encapsulated in an anticoagulant, hemocompatible polysaccharide, 6-O-chitosan sulfate, is presented. Three different approaches are described for the immobilization of these core shell particles on cellulosic surfaces. The mass of the immobilized particles is quantified using a quartz crystal microbalance with dissipation (QCM-D). The antimicrobial activity of the surfaces towards E. coli MG 1655 [R1-16] is investigated by live/dead assays using fluorescence staining. All surfaces treated with the designed nanoparticles exhibit excellent antimicrobial activity towards E. coli MG 1655 [R1-16]. Anticoagulant properties of blood plasma on the nanoparticle treated surfaces have been determined using QCM-D. In comparison with the unmodified substrates, the total coagulation time as well as the thrombin formation time and fibrin clotting time of surfaces modified with nanoparticles are significantly increased.

Silanetriols as in vitro inhibitors for AChE

Graphical abstract

Creating water vapor barrier coatings from hydrophilic components.

The preparation of water vapor barrier coatings composed of polyelectrolyte/clay multilayers using the layer-by-layer technique is reported. The suitability of different synthetic and renewable polyelectrolytes for the preparation of barrier coatings in combination with montmorillonite (MMT) platelets as well as the influence of the ionic strength and the number of bilayers on the coating performance was investigated. Highly hydrophilic and permeable cellulose films were used as substrate for determining the influence of the coatings on the water vapor transmission rate (WVTR). Improved barrier properties were realized by the use of polyethylene imine (PEI) or 2-hydroxy-3-trimethylammonium propyl chloride starch (HPMA starch) in combination with MMT. After the application of only 5 bilayers of PEI and MMT (thickness ∼40 nm) on each side of the cellulose film, the WVTR was significantly reduced. By the deposition of 40 PEI/MMT bilayers, the WVTR transmission rate was reduced by 68%. However, HPMA starch containing coatings led to vapor transmission reduction of up to 32% at the same number of coating steps. A strong correlation between the barrier properties of the coatings and the layer thickness was observed. The barrier properties of the coatings could be increased using higher ionic strengths. These results represent unprecedented water vapor barrier properties for coatings prepared from hydrophilic materials.