Steffen Hädrich

Fiber chirped-pulse amplification system emitting 3.8 GW peak power

We report on the experimental demonstration of a fiber chirped- pulse amplification system capable of generating nearly transform-limited sub 500 fs pulses with 2.2 mJ pulse energy at 11 W average power. The resulting record peak power of 3.8 GW could be achieved by combining active phase shaping with an efficient reduction of the acquired nonlinear phase. Therefore, we used an Ytterbium-doped large-pitch fiber with a mode field diameter of 105 µm as the main amplifier.

Octave-spanning OPCPA system delivering CEP-stable few-cycle pulses and 22 W of average power at 1 MHz repetition rate

We report on an OPCPA system delivering CEP-stable pulses with a pulse duration of only 1.7 optical cycles at 880 nm wavelength. This pulse duration is achieved by the generation, optical parametric amplification and compression of a full optical octave of bandwidth. The system is pumped by a high average power Yb-fiber laser system, which allows for operation of the OPCPA at up to 1 MHz repetition rate and 22 W of average output power. Further scaling towards single-cycle pulses, higher energy and output power is discussed.

High photon flux table-top coherent extreme-ultraviolet source

High photon flux with up to 1012 photons in the 25–40 eV range has been achieved in a new table-top coherent extreme ultraviolet (EUV) source based on phase-matched high-harmonic generation using a fibre laser. Intense and compact EUV sources are needed for certain types of spectroscopic and imaging applications.

Yb:YAG Innoslab amplifier: efficient high repetition rate subpicosecond pumping system for optical parametric chirped pulse amplification

We report on a Yb:YAG Innoslab laser amplifier system for generation of subpicsecond high energy pump pulses for optical parametric chirped pulse amplification (OPCPA) at high repetition rates. Pulse energies of up to 20 mJ (at 12.5 kHz) and repetition rates of up to 100 kHz were attained with pulse durations of 830 fs and average power in excess of 200 W. We further investigate the possibility to use subpicosecond pulses to derive a stable continuum in a YAG crystal for OPCPA seeding.

High Repetition Rate Gigawatt Peak Power Fiber Laser Systems: Challenges, Design, and Experiment

We review the main challenges and give design guidelines for high-peak-power high-average-power fiber-based chirped-pulse amplification (CPA) systems. It is clearly pointed out that the lowest order fiber nonlinearity (NL), namely the self-phase modulation, limits the scalability of high-energy ultrashort pulse fiber amplifiers. Therefore, a distinguished difference arises between the consequences of accumulated nonlinear phase originating from the pulse envelope and initial weak modulations, resulting in a strong recommendation to operate an amplification system as linearly as possible in order to generate high-contrast pulses. Low-NL rare-earth-doped fibers, such as the recently available designs of photonic crystal fibers, are the key element for successful peak power scaling in fiber laser systems. In this paper, we present a detailed analysis and optimization of the extraction characteristics in connection with the accumulated nonlinear phase in such extreme fiber dimensions. Consequently, millijoule pulse energy femtosecond pulses at repetition rates in the 100 kHz range have already been demonstrated experimentally in a Yb-fiber-based CPA system that has even further scaling potential.

Energy scaling of femtosecond amplifiers using actively controlled divided-pulse amplification

Divided-pulse amplification is a promising method for the energy scaling of femtosecond laser amplifiers, where pulses are temporally split prior to amplification and coherently recombined afterwards. We present a method that uses an actively stabilized setup with separated stages for splitting and combining. The additional degrees of freedom can be employed to mitigate the limitations originating from saturation of the amplifier that cannot be compensated in passive double-pass configurations using just one common stage for pulse splitting and combining. In a first proof-of-principle experiment, actively controlled divided pulses are applied in a fiber chirped-pulse amplification system resulting in combined and compressed pulses with an energy of 1.25 mJ and a peak power of 2.9 GW.

Thermal effects in high average power optical parametric amplifiers

Optical parametric amplifiers (OPAs) have the reputation of being average power scalable due to the instantaneous nature of the parametric process (zero quantum defect). This Letter reveals serious challenges originating from thermal load in the nonlinear crystal caused by absorption. We investigate these thermal effects in high average power OPAs based on beta barium borate. Absorption of both pump and idler waves is identified to contribute significantly to heating of the nonlinear crystal. A temperature increase of up to 148 K with respect to the environment is observed and mechanical tensile stress up to 40 MPa is found, indicating a high risk of crystal fracture under such conditions. By restricting the idler to a wavelength range far from absorption bands and removing the crystal coating we reduce the peak temperature and the resulting temperature gradient significantly. Guidelines for further power scaling of OPAs and other nonlinear devices are given.

Sub 25 fs pulses from solid-core nonlinear compression stage at 250 W of average power

We report on a highpower femtosecond fiber chirped-pulse amplification system with an excellent beam quality (M(2)=1.2) operating at 250 MHz repetition rate. We demonstrate nonlinear compression in a solid-core photonic crystal fiber at unprecedented average power levels. By exploiting self-phase modulation with subsequent chirped-mirror compression we achieve pulse shortening by more than one order of magnitude to 23 fs pulses. The use of circular polarization allows higher than usual peak powers in the broadening fiber resulting in compressed 0.9 μJ pulse energy and a peak power of 34 MW at 250 W of average power (M(2)=1.3). This system is well suited for driving cavity-enhanced high-repetition rate high-harmonic generation.

53 W average power few-cycle fiber laser system generating soft x rays up to the water window

We report on a few-cycle laser system delivering sub-8-fs pulses with 353 μJ pulse energy and 25 GW of peak power at up to 150 kHz repetition rate. The corresponding average output power is as high as 53 W, which represents the highest average power obtained from any few-cycle laser architecture so far. The combination of both high average and high peak power provides unique opportunities for applications. We demonstrate high harmonic generation up to the water window and record-high photon flux in the soft x-ray spectral region. This tabletop source of high-photon flux soft x rays will, for example, enable coherent diffractive imaging with sub-10-nm resolution in the near future.

High average and peak power few-cycle laser pulses delivered by fiber pumped OPCPA system

We report on a high power optical parametric amplifier delivering 8 fs pulses with 6 GW peak power. The system is pumped by a fiber amplifier and operated at 96 kHz repetition rate. The average output power is as high as 6.7 W, which is the highest average power few-cycle pulse laser reported so far. When stabilizing the seed oscillator, the system delivered carrier-envelop phase stable laser pulses. Furthermore, high harmonic generation up to the 33(th) order (21.8 nm) is demonstrated in a Krypton gas jet. In addition, the scalability of the presented laser system is discussed.