Stephane Salmieri

Mechanical and barrier properties of nanocrystalline cellulose reinforced chitosan based nanocomposite films

Nanocrystalline cellulose (NCC) reinforced chitosan-based biodegradable films were prepared by solution casting. The NCC content in the films was varied from 1 to 10% (dry wt. basis). It was found that the tensile strength (TS) of the nanocomposite films with 5% (w/w) NCC content was optimum with an improvement of 26% compared to the control chitosan films. Incorporation of NCC also significantly improved barrier properties. Water vapor permeability (WVP) of the chitosan/NCC films was decreased by 27% for the optimum 5% (w/w) NCC content. Swelling studies revealed a decrease in water uptake of the NCC-reinforced chitosan films. Analyses of thermal properties showed no significant effect of NCC whereas X-ray diffraction studies confirmed the appearance of crystalline peaks in the nanocomposite films. Surface morphology of the films was investigated by scanning electron microscopy and it was found that NCC was dispersed homogenously into chitosan matrix.

Nanocrystalline cellulose (NCC) reinforced alginate based biodegradable nanocomposite film.

Nanocrystalline cellulose (NCC) reinforced alginate-based nanocomposite film was prepared by solution casting. The NCC content in the matrix was varied from 1 to 8% ((w/w) % dry matrix). It was found that the nanocomposite reinforced with 5 wt% NCC content exhibits the highest tensile strength which was increased by 37% compared to the control. Incorporation of NCC also significantly improved water vapor permeability (WVP) of the nanocomposite showing a 31% decrease due to 5 wt% NCC loading. Molecular interactions between alginate and NCC were supported by Fourier Transform Infrared Spectroscopy. The X-ray diffraction studies also confirmed the appearance of crystalline peaks due to the presence of NCC inside the films. Thermal stability of alginate-based nanocomposite films was improved after incorporation of NCC.

Production and Properties of Nanocellulose-Reinforced Methylcellulose-Based Biodegradable Films

Methylcellulose (MC)-based films were prepared by casting from its 1% aqueous solution containing 0.5% vegetable oil, 0.25% glycerol, and 0.025% Tween 80. Puncture strength (PS), puncture deformation (PD), viscoelasticity coefficient, and water vapor permeability (WVP) were found to be 147 N/mm, 3.46 mm, 41%, and 6.34 g.mm/m(2).day.kPa, respectively. Aqueous nanocellulose (NC) solution (0.1-1%) was incorporated into the MC-based formulation, and it was found that PS was improved (117%) and WVP was decreased (26%) significantly. Films containing 0.25% NC were found to be the optimum. Then films were exposed to gamma radiation (0.5-50 kGy), and it was revealed that mechanical properties of the films were slightly decreased after irradiation, whereas barrier properties were further improved with a decrease of WVP to 28.8% at 50 kGy. Molecular interactions due to incorporation of NC were supported by FTIR spectroscopy. Thermal properties of the NC-containing films were improved, confirmed by TGA and DSC. Crystalline peaks appeared due to NC addition, found by XRD. Micrographs of films containing NC were investigated by SEM.

Antimicrobial Effects of Alginate-Based Film Containing Essential Oils for the Preservation of Whole Beef Muscle

Alginate-based edible films containing 1% (wt/vol) essential oils of Spanish oregano, Chinese cinnamon, or savory were immersed in 2% (wt/vol) or 20% (wt/vol) CaCl2 solution and then applied to beef muscle slices to control the growth of Escherichia coli O157:H7 and Salmonella Typhimurium. Whole beef muscle surfaces were inoculated with one of these strains at 10(3) CFU/cm2. During the 5 days of storage, samples of meat were obtained periodically for microbiological analysis. The availability of active compounds from essential oils present in films was evaluated by determination of total phenolic compounds for oregano- and savory-based films and of total aldehydes for cinnamon-based films during storage. After 5 days of storage, films containing oregano or cinnamon essential oils were the most effective against Salmonella Typhimurium regardless of the type of pretreatment used (2 or 20% CaCl2). During the same period, meat inoculated with E. coli O157:H7 and coated with films treated with 2% CaCl2 had significantly fewer bacteria (P < or = 0.05) when oregano-based films were used than when cinnamon- and savory-based films were used. The E. coli O157:H7 concentration was higher at the end of the storage period when films were pretreated with 20% CaCl2. Evaluation of the active compounds in films revealed that availability in oregano- and savory-based films was significantly more important (P < or = 0.05) than that in cinnamon-based films regardless of the type of pretreatment used (2 or 20% CaCl2). At the end of storage, release rates of 40, 60, and 77% were noted in oregano-, savory-, and cinnamon-based films in 2% CaCl2 and rates of 65, 62, and 90% were noted in the same films in 20% CaCl2.

Antimicrobial Effects of Alginate-Based Films Containing Essential Oils on Listeria monocytogenes and Salmonella Typhimurium Present in Bologna and Ham

Bologna and ham slices (300 of each) were inoculated with Salmonella Typhimurium or Listeria monocytogenes at 10(3) CFU/cm(2). Alginate-based edible films that had been immersed in a 2 or 20% (wt/vol) CaC12 solution and contained 1% (wt/ vol) essential oils of Spanish oregano (O; Corydothymus capitatus), Chinese cinnamon (C; Cinnamomum cassia), or winter savory (S; Satureja montana) were then applied to slices to control pathogen growth. On bologna, C-based films pretreated with 20% CaC12 were the most effective against the growth of Salmonella Typhimurium and L. monocytogenes. L. monocytogenes was the more sensitive bacterium to O-, C-, and S-based films. L. monocytogenes concentrations were below the detection level (<10 CFU/ml) after 5 days of storage on bologna coated with O-, C-, or S-based films pretreated with 20% CaCl2. On ham, a 1.85 log CFU/cm2 reduction of Salmonella Typhimurium (P < 0.05) was found after 5 days of storage with C-based films regardless of the type of pretreatment used (2 or 20% CaC12) or when coated with O-based films pretreated with 20% CaCl2. L. monocytogenes was highly resistant in ham, even in the presence of O-, C-, or S-based films. However, C-based films pretreated with 20% CaCl2 were the most effective against the growth of L. monocytogenes. Evaluation of the availability of active compounds in films revealed a significantly higher release of active compounds in C-based films (P < 0.05) regardless of pretreatment or meat tested (bologna or ham). O-based films had the lowest release level of active compounds. The release of active compounds from O- and S-based films pretreated with 20% CaCl2 was faster than that in the same respective films pretreated with 2% CaCl2 regardless of the meat type. C-based film pretreated by immersion in a 20% CaCl2 solution was most efficient against both pathogens, and migration of active compounds was higher in C-based films than in O- and S-based films.

Combined Effects of Antimicrobial Coating, Modified Atmosphere Packaging, and Gamma Irradiation on Listeria innocua Present in Ready-to-Use Carrots (Daucus carota)

The objective of this study was to evaluate the effect of an edible antimicrobial coating combined with modified atmosphere (MA) packaging (60% O2, 30% CO2, and 10% N2) and gamma irradiation on peeled minicarrots inoculated with Listeria innocua. Carrots were inoculated with L. innocua (10(3) CFU/g) and then coated with an antimicrobial coating based on calcium caseinate containing trans-cinnamaldehyde. The same formulation without trans-cinnamaldehyde was used as an inactive coating. Coated and uncoated carrots were packed under the MA or under air, irradiated at 0.25 or 0.5 kGy, and stored at 4 +/- 1 degrees C for 21 days. Samples were evaluated periodically for enumeration of L. innocua. Unirradiated carrots stored under air had the highest concentrations of L. innocua after 21 days of storage: 2.23 CFU/g in the uncoated samples and 2.26 CFU/ g in samples coated with the inactive coating. These results suggest that the inactive coating did not have any antimicrobial effect against L. innocua. However, the addition of the antimicrobial coating resulted in a 1.29-log reduction in the concentration of L. innocua in carrots packed under air after 21 days of storage and a 1.08-log reduction in carrots packed under MA after 7 days of storage. After 7 days of storage, no L. innocua was detected in samples treated at 0.5 kGy under air or in samples treated at 0.25 kGy under MA. A complete inhibition of L. innocua was also observed during all storage periods in uncoated and coated samples treated at 0.5 kGy under MA. These results indicate that the combination of irradiation and MA conditions play an important role in the radiosensitization of L. innocua.

Effect of Selected Plant Essential Oils or Their Constituents and Modified Atmosphere Packaging on the Radiosensitivity of Escherichia coli O157:H7 and Salmonella Typhi in Ground Beef

Twenty-six different essential oils were tested for their efficiency to increase the relative radiosensitivity of Escherichia coli and Salmonella Typhi in medium-fat ground beef (23% fat). Ground beef was inoculated with E. coli O157:H7 or Salmonella (10(6) CFU/g), and each essential oil or one of their main constituents was added separately at a concentration of 0.5% (wt/wt). Meat samples (10 g) were packed under air or under modified atmosphere and irradiated at doses from 0 to 1 kGy for the determination of the D10-value of E. coli O157:H7, and from 0 to 1.75 kGy for the determination of the D10-value of Salmonella Typhi. Depending on the compound tested, the relative radiation sensitivity increased from 1 to 3.57 for E. coli O157:H7 and from 1 to 3.26 for Salmonella Typhi. Addition of essential oils or their constituents before irradiation also reduced the irradiation dose needed to eliminate both pathogens. In the presence of Chinese cinnamon or Spanish oregano essential oils, the minimum doses required to eliminate the bacteria were reduced from 1.2 to 0.35 and from 1.4 to 0.5 for E. coli O157:H7 and Salmonella Typhi, respectively. Cinnamon, oregano, and mustard essential oils were the most effective radiosensitizers.

Improvement of water barrier property of paperboard by coating application with biodegradable polymers.

Biopolymeric coatings were prepared and applied onto paperboard to improve its water barrier property. To prepare whey protein isolate (WPI)/cellulose-based films, WPI and glycerol were dissolved in water with glutaraldehyde (cross-linking agent) and cellulose xanthate. The solution was cast, dried, and insolubilized by entrapment of WPI in regenerated cellulose. Films were combined with beeswax (BW) into a bilayer coating system and then applied onto paperboard by heating compression. Another coating solution consisting of poly(vinyl butyral) (PVB)/zein was prepared by dissolving poly(vinyl alcohol) (PVA) and zein in 70% ethanol with glutaraldehyde and butyraldehyde (functionalization agent). The PVB/zein solution was applied onto paperboard after BW was sprayed. The structure of the PVB/zein-based coatings was analyzed by Fourier transform infrared spectroscopy (FTIR). The water vapor barrier property of coated paperboards was evaluated by water vapor transmission rate (WVTR) measurements. From the FTIR spectra, PVA functionalization after cross-linking and efficient acetalization into PVB were confirmed. WPI/cellulose and PVB/zein coating treatments improved the water barrier properties of paperboard by decreasing the WVTR by 77-78%. Although the BW coating was more efficient (decrease of WVTR by 89%), bilayer coatings composed of BW and polymer coatings had a stronger barrier effect with a decrease of WVTR to 92-95%, hence approaching commercial attributes required to ensure water vapor barrier in paperboard-based food containers (10 g/m(2).day). These results suggest that surface coating by biodegradable polymers may be utilized for the manufacture of paperboard containers in industrial applications.

Antibacterial and physical effects of modified chitosan based-coating containing nanoemulsion of mandarin essential oil and three non-thermal treatments against Listeria innocua in green beans

The antimicrobial activity against Listeria innocua of three different combined non-thermal treatments, along with the impact on color and texture on green bean samples, was evaluated. In this study a bioactive coating formulation based on modified chitosan containing 0.05% nanoemulsion of mandarin essential oil was tested in combination with γ-irradiation, UV-C and ozonated water treatments, and the results in terms of antimicrobial activity, color and texture changes, were evaluated during 14 days storage. The combined coating and γ-irradiation treatment gave promising results, showing 3.3 log CFU/g initial microbial reduction, and exhibiting a strong synergistic antimicrobial effect. The treatment based on UV-C and coating formulation allowed a 3 log CFU/g reduction of initial L. innocua population on samples, showing a good residual antimicrobial activity and preventing loss of firmness and color changes during storage. The combined treatment of coating and ozonated water did not show any synergistic or additive antimicrobial effect, but they showed an impact on firmness and color. In conclusion UV-C and γ-irradiation treatments, in combination with the bioactive coating, represent an effective approach to control the growth of L. innocua on vegetable foods.

Improving the Compatibility of Zein/Poly(vinyl alcohol) Blends by Gamma Irradiation and Graft Copolymerization of Acrylic Acid

The effect of gamma irradiation and graft copolymerization with different ratios of acrylic acid monomer (AAc) on improving the compatibility of polymeric blends based on zein, as natural protein, and different ratios of poly(vinyl alcohol) (PVA) up to 50% were studied. The structure property of the polymeric blends was characterized by Fourier transform infrared spectroscopy (FTIR), mechanical testing, scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The FTIR analysis indicated that grafted AAc into zein/PVA matrix was stabilized by hydrogen bonding. The stress-strain curves showed that pure zein films were brittle, whereas pure PVA and zein/PVA blends films were tough materials either before or after gamma irradiation. The SEM micrographs indicated the formation of multilayers during the blending of zein and PVA, and these layers turned to dispersion in matrix after gamma irradiation and grafting with AAc, suggesting an effectiveness of gamma irradiation on improving compatibility.