Sudip K Samanta

Eulerian two-phase flow simulation and experimental validation of semisolid slurry generation process using cooling slope

Abstract Experimental and numerical studies of slurry generation using a cooling slope are presented in the paper. The slope having stainless steel body has been designed and constructed to produce semisolid A356 Al alloy slurry. The pouring temperature of molten metal, slope angle of the cooling slope and slope wall temperature were varied during the experiment. A multiphase numerical model, considering liquid metal and air, has been developed to simulate the liquid metal flow along the cooling channel using an Eulerian two-phase flow approach. Solid fraction evolution of the solidifying melt is tracked at different locations of the cooling channel following Schiel’s equation. The continuity, momentum and energy equations are solved considering thin wall boundary condition approach. During solidification of the melt, based on the liquid fraction and latent heat of the alloy, temperature of the alloy is modified continuously by introducing a modified temperature recovery method. Numerical simulations has been carried out for semisolid slurry formation by varying the process parameters such as angle of the cooling slope, cooling slope wall temperature and melt superheat temperature, to understand the effect of process variables on cooling slope semisolid slurry generation process such as temperature distribution, velocity distribution and solid fraction of the solidifying melt. Experimental validation performed for some chosen cases reveals good agreement with the numerical simulations.

Evaluation of primary phase morphology of cooling slope cast Al-Si-Mg alloy samples using image texture analysis

Rheopressure die casting is one of the newest casting processes of present era for manufacturing of near-net-shaped cast components with improved mechanical properties and high-dimensional accuracy. Rheopressure die casting demands especially prepared semi-solid alloy slurry having nearly globular primary Al phase. In this study, a cooling slope has been employed to produce semi-solid slurry of Al-Si-Mg (A356) alloy and successively cast in a metallic mould. Image texture analysis techniques have been implemented for accurate evaluation of the primary phase morphology of cast samples. In this research, efforts have been made to apply fractal analysis and run-length statistical analysis techniques for automatic characterization of optical micrographs of cast samples produced at different processing conditions.

Effect of pouring temperature on cooling slope casting of semi-solid Al-Si-Mg alloy

Present trend of semi-solid processing is directed towards rheocasting route which allows manufacturing of near-net-shape cast components directly from the prepared semi-solid slurry. Generation of globular equi-axed grains during solidification of rheocast components, compared to the columnar dendritic structure of conventional casting routes, facilitates the manufacturing of components with improved mechanical properties and structural integrity. In the present investigation, a cooling slope has been designed and indigenously fabricated to produce semi solid slurry of Al-Si-Mg (A356) alloy and successively cast in a metallic mould. The scope of the present work discusses about development of a numerical model to simulate the liquid metal flow through cooling slope using Eulerian two-phase flow approach and to investigate the effect of pouring temperature on cooling slope semi-solid slurry generation process. The two phases considered in the present model are liquid metal and air. Solid fraction evolution of the solidifying melt is tracked at different locations of the cooling slope, following Schiels equation. The continuity equation, momentum equation and energy equation are solved considering thin wall boundary condition approach. During solidification of the liquid metal, a modified temperature recovery scheme has been employed taking care of the latent heat release and change of fraction of liquid. The results obtained from simulations are compared with experimental findings and good agreement has been found.

Mechanical Properties and Tensile Fracture Mechanism of Rheocast A356 Al Alloy Using Cooling Slope

A356 aluminium alloy has a wide applicability in the manufacturing of automotive parts. Cooling slope (CS) rheocasting process has been used in the present work to produce A356 billets having near spherical morphology of primary Al phase. Absence of dendritic primary phase, observed in case conventionally cast A356 alloy, and finer distribution of secondary eutectic Si phase within the matrix establishes the usefulness of the CS casting route. Near spherical primary phase in the rheocast alloy ensures better strength, elongation properties and structural integrity in the produced billets. The liquid melt is allowed to flow through the cooling slope after pouring at 6500C. Rapid heat exchange between the flowing melt and slope wall and the atmosphere facilitates heterogeneous nucleation of α-Al phase on the cooling slope wall. Shear driven flow of the solidifying melt is found responsible for separation of α-Al phase from the slope wall and generation of nearly spherical morphology of the primary phase in the microstructure. Grain refiner addition in the melt leads to enhance the primary α-Al percentage in the microstructure and also aids to the improvement of degree of sphericity and reduction of spheroid size. So, grain refining helps to improve the strength, elongation and fracture properties of rheocast billets further.

Rheological Behavior of Al-7Si-0.3Mg Alloy at Mushy State

In recent years, semisolid manufacturing has emerged as an attractive option for near net shape forming of components with aluminum alloys. In this class of processes, the key to success lies mainly in the understanding of rheological behavior of the semi-solid slurry in the temperature range between liquidus and solidus. The present study focuses on the non-Newtonian flow behavior of the pseudo plastic slurry of Al-7Si-0.3Mg alloy for a wide shear range using a high-temperature Searle-type rheometer. The rheological behavior of the slurry is studied with respect to relevant process variables and microstructural features such as shear rate, shear duration, temperature history, primary particle size, shape, and their distribution. The experiments performed are isothermal tests, continuous cooling tests, shear jump tests, and shear time tests. The continuous cooling experiments are aimed toward studying the viscosity and shear stress evolution within the slurry matrix with increasing solid fraction at a constant shear rate. Three different cooling rates are considered and their effect on flow behavior of the slurry was studied under iso-shear condition. Descending shear jump experiments are performed to understand the viscous instability of the slurry.

Semisolid Processing of A380 Al Alloy Using Cooling Slope

This study is aimed toward obtaining near spherical microstructural features of Rheocast A380 aluminum alloy. Cooling slope (CS) technique has been used to generate semisolid slurry from the superheated alloy melt. Spherodization of primary grains is the heart of semisolid processing which improves mechanical properties significantly in the parts cast from semisolid state compared to the conventional casting processes. Keeping in view of the desired microstructural morphology, i.e., rosette or spherical shape of primary α-Al phase, successive slurry samples have been collected during melt flow and oil quenched to investigate the microstructure evolution mechanism. Conventionally cast A380 Al alloy sample shows dendritic grains surrounded by large eutectic phase whereas finer, near spherical grains have been observed within the cooling slope processed slurry and also in the solidified castings which confirms the effectiveness of semisolid processing of the alloy following cooling slope technique. Grain refiner addition into the alloy melt is found to have favorable effect which leads to the generation of finer primary grains within the slurry with higher degree of sphericity.

Modelling the powder?binder separation in injection stage of PIM

In this paper, a non-isothermal multiphase flow numerical model has been developed based on Eulerian approach to simulate the powder-binder separation phenomenon in the injection stage of Powder Injection Moulding (PIM) and the simulated results are validated with experiments. The model takes into account of the non Newtonian viscosity of the powder and binder phases. Simulation as well as experiments have been carried out for a standard tensile test specimen with gating and ejection systems. A temperature correction method has been introduced during solidification taking into account of the latent heat release of binder. It can be seen from the simulated results that injection temperature has larger effect on phase segregation than injection speed due to larger effect of temperature on viscosity.

Study of Microstructure Evolution during Semi-Solid Processing of an In-Situ Al Alloy Composite

In the present work, effect of pouring temperature (650°C, 655°C, and 660°C) on semi-solid microstructure evolution of in-situ magnesium silicide (Mg2Si) reinforced aluminum (Al) alloy composite has been studied. The shear force exerted by the cooling slope during gravity driven flow of the melt facilitates the formation of near spherical primary Mg2Si and primary Al grains. Shear driven melt flow along the cooling slope and grain fragmentation have been identified as the responsible mechanisms for refinement of primary Mg2Si and Al grains with improved sphericity. Results show that, while flowing down the cooling slope, morphology of primary Mg2Si and primary Al transformed gradually from coarse dendritic to mixture of near spherical particles, rosettes, and degenerated dendrites. In terms of minimum grain size and maximum sphericity, 650°C has been identified as the ideal pouring temperature for the cooling slope semi-solid processing of present Al alloy composite. Formation of spheroidal grains with homogeneous distribution of reinforcing phase (Mg2Si) improves the isotropic property of the said composite, which is desirable in most of the engineering applications.

Studies on rheocasting using cooling slope

In the present work, a cooling channel is employed to produce semi-solid A356 alloy slurry. To understand the transport process involved, a 3D non-isothermal, multiphase volume averaging model has been developed for simulation of the semi-solid slurry generation process in the cooling channel. For simulation purpose, the three phases considered are the parent melt, the nearly spherical grains and air as separated but highly coupled interpenetrating continua. The conservation equations of mass, momentum, energy and species have been solved for each phase and the thermal and mechanical interactions (drag force) among the phases have been considered using appropriate model. The superheated liquid alloy is poured at the top of the cooling slope/channel, where specified velocity inlet boundary condition is used in the model, and allowed to flow along gravity through the channel. The melt loses its superheat and becomes semisolid up to the end of cooling channel due to the evolving -Al grains with decreasing temperature. The air phase forms a definable air/liquid melt interface, i.e. free surface, due its low density. The results obtained from the present model includes volume fractions of three different phases considered, grain evolution, grain growth rate, size and distribution of solid grains. The effect of key process variables such as pouring temperature, slope angle of the cooling channel and cooling channel wall temperature on temperature distribution, velocity distribution, grain formation and volume fraction of different phases are also studied. The results obtained from the simulations are validated by microstructure study using SEM and quantitative image analysis of the semi-solid slurry microstructure obtained from the experimental set-up.

A comparative assessment of crystallite size and lattice strain in differently cast A356 aluminium alloy

In this investigation, A356 aluminium alloy has been prepared by different routes viz. gravity casting, rheo pressure die casting (RPDC) and RPDC with T6 heat treatment. X-ray diffraction studies of these samples have been done in the scanning range of 20 – 90°. X-ray peak broadening analysis has been used to estimate the crystallite size and lattice stain, in all the samples. The sample prepared by RPDC with T6 treatment has comparatively smaller crystallite size and lesser lattice strain than gravity cast and RPDC samples.