nan Suyatman

Improved Performances of Ethanol Sensor Fabricated on Al-Doped ZnO Nanosheet Thin Films

The effect of Al-doped ZnO (AZO) to the sensitivity improvement of ethanol vapor sensor was investigated. The pure ZnO and AZO thin films were synthesized by chemical bath deposition method. Analysis of the crystal structure, chemical composition, and morphology of the samples are carried out using X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), and scanning electron microscopy (SEM). XRD results show that the phase formed is polycrystalline Zn, while the EDS measurements show that the composition of after synthesized AZO were 1.48 at%, 2.90 at%, and 3.55 at%. The SEM results showed flowerlike microstrcuture and nanosheet shaped are formed in the resulting thin films, which are captured by the formation of sheets of transparent structure in AZO. Moreover, the resulting ZnO and AZO sensors were exposed to the different concentration of ethanol vapor as much as 200, 400, and 600 ppm, respectively. The measurement of vapor sensor system performance was tested to analyze the sensitivity and the responsiveness of the AZO thin films. The sensors have highest sensitivity at certain amount of Al doping. It is obtained that the optimum sensitivity of the sensor is investigated at the sample of 2.9 at% Al-ZnO. The sensitivity for pure ZnO sample at concentration of 200, 400, and 600 ppm of ethanol were 70.88%, 78.21%, and 88.57%, respectively. The highest sensitivity for AZO samples is 95.29% at low ethanol concentrations (200 ppm) and 96.68% at the high concentration (parts per million), respectively.

A combined spectroscopic and TDDFT study of natural dyes extracted from fruit peels of Citrus reticulata and Musa acuminata for dye-sensitized solar cells

This study reports the novel spectroscopic investigations and enhanced the electron transfers of Citrus reticulata and Musa acuminata fruit peels as the photosensitizers for the dye-sensitized solar cells. The calculated TD-DFT-UB3LYP/6-31+G(d,p)-IEFPCM(UAKS), experiment spectra of ultra-violet-visible spectroscopy, and Fourier transform infrared spectroscopy studies indicate the main flavonoid (hesperidin and gallocatechin) structures of the dye extracts. The optimized flavonoid structures are calculated using Density functional theory (DFT) at 6-31+G(d,p) level. The rutinosyl group of the hesperidin pigment (Citrus reticulata) will be further investigated compared to the gallocatechin (Musa acuminata) pigment. The acidity of the dye extract is treated by adding 2% acetic acid. The energy levels of the HOMO-LUMO dyes are measured by a combined Tauc plot and cyclic voltammetry contrasted with the DFT data. The electrochemical impedance spectroscopy will be performed to model the dye electron transfer. As for the rutinosyl group presence and the acidic treatment, the acidified Citrus reticulata cell under continuous light exposure of 100mW·cm-2 yields a short-circuit current density (Jsc) of 3.23mA/cm2, a photovoltage (Voc) of 0.48V, and a fill factor of 0.45 corresponding to an energy conversion efficiency (η) of 0.71% because the shifting down HOMO-LUMO edges and the broadening dyes absorbance evaluated by a combined spectroscopic and TD-DFT method. The result also leads to the longest diffusion length of 32.2μm, the fastest electron transit of 0.22ms, and the longest electron lifetime of 4.29ms.

Ground and excited state properties of high performance anthocyanidin dyes-sensitized solar cells in the basic solutions

The aglycones of anthocyanidin dyes were previously reported to form carbinol pseudobase, cis-chalcone, and trans-chalcone due to the basic levels. The further investigations of ground and excited state properties of the dyes were characterized using density functional theory with PCM(UFF)/B3LYP/6-31+G(d,p) level in the basic solutions. However, to the best of our knowledge, the theoretical investigation of their potential photosensitizers has never been reported before. In this paper, the theoretical photovoltaic properties sensitized by dyes have been successfully investigated including the electron injections, the ground and excited state oxidation potentials, the estimated open circuit voltages, and the light harvesting efficiencies. The results prove that the electronic properties represented by dyes’ LUMO-HOMO levels will affect to the photovoltaic performances. Cis-chalcone dye is the best anthocyanidin aglycone dye with the electron injection spontaneity of −1.208 eV, the theoretical open circuit ...

Synthesis and Characterization of SnO2 Thin Films by Chemical Bath Deposition

SnO2 thin films were deposited on glass substrate by chemical bath deposition (CBD) with stannous chloride (SnCl2..2H2O) as a precursor and urea (CO(NH2)2) as a buffer. X‐Ray Diffraction (XRD) are used to characterize the structure of the films; the surface morphology of the films were observed by Scanning Electron Microscope (SEM). Using this techniques, we specify the effect of stannous chloride concentration and weight ratio of urea/H2O on the crystallinity and morphology of these films. The rutile structure corresponding (110), (101) and (211) planes of SnO2 is obtained. The increasing of stannous chloride concentration and the decreasing weight ratio of urea/H2O is found to improve the crystallinity of the film. The average diameter of grain size is about 96 nm.

Boundary potential distribution in rectangular object based on data collection system

One of the problems that exist in the EIT is less sensitive of boundary potential changes due to changes in the parameters object at a distance from the edge. This boundary potential distribution pattern is determined by a given current injection pattern. Thus need to know the combination of current injection patterns and methods of data collection potential corresponding boundary. The data collection system should determine the value of sensitivity and have the certain ability to detect changes in the object parameters. In this study, the data collection system will be tested on a rectangular-shaped object. Forward model analysis toward the pattern of boundary potential is conducted. The results showed that the pattern of boundary potential should be considered in reconstruction process except a large sensitivity.

Al‐doped ZnO Thin Films for Ethanol Sensors

Al doped ZnO (AZO) is done to understand the effect of Al dopant on ZnO. The sensor response condition will be analyzed for ethanol detection. Chemical Bath Deposition (CBD) method is used to fabrication pure ZnO and AZO thin films. Al dopant concentrations used in this study is 2.9 at% Al. The crystallinity, composition and morphology were investigated by using XRD, EDS and SEM. The ZnO and AZO gas sensors were exposed to different concentrations of ethanol at room temperature, 2.5%, 5% and 7.5% volume ethanol, respectively. The sensor response at low concentrations (2.5% V) for pure ZnO sample is 70.88% and 88.57% for high concentrations of ethanol (7.5% V). The highest sensor response for AZO sample is 95.29% at low concentrations (2.5% V) and 96.68% V at the high concentration (7.5% V).

The synthesis of Fe3O4/MWCNT nanocomposites from local iron sands for electrochemical sensors

The aim of this research is producing the electrochemical sensor, especially for working electrodes based on the nanocomposites of multi-walled carbon nanotube (MWCNT) and magnetite (Fe3O4) nanoparticles from iron sands. The sonochemical method by ultrasonic horn was successfully used for the synthesis of the nanocomposites. The characterizations of the sample were conducted via X-Ray Diffractometer (XRD), Fourier Transform Infra-Red (FTIR) Spectrometer, Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Brunauer-Emmett-Teller (BET) method for surface area, Vibrating Sample Magnetometer (VSM) and Cyclic Voltammetry (CV). The analysis of X-Ray Diffraction (XRD) pattern showed two phases of crystalline, namely MWCNT and Fe3O4, peak of MWCNT comes from (002) plan while peaks of Fe3O4 come from (2 2 0), (3 1 1), (4 0 0), (4 2 2), (5 1 1), and (4 4 0) plans. From XRD data, MWCNT has a hexagonal structure and Fe3O4 has inverse spinel cubic structure, respectively. The FTIR spectra revealed that the functionalization process of MWCNT successfully generated carboxyl and carbonyl groups to bind Fe3O4 on MWCNT surfaces. Moreover, the functional groups of Fe-O bonding that showed the existence of Fe3O4 in the nanocomposites were also detected in those spectra. Meanwhile, the SEM and TEM images showed that the nanoparticles of Fe3O4 attached on the MWCNT surface and formed agglomeration between particles due to magnetic forces. Through Brunauer-Emmett-Teller (BET) method, it is identified that the nanocomposite has a large surface area 318 m2/g that makes this material very suitable for electrochemical sensor applications. Moreover, the characterization of magnetic properties via Vibrating Sample Magnetometer (VSM) showed that the nanocomposites have superparamagnetic behavior at room temperature and the presence of the MWCNT reduced the magnetic properties of Fe3O4. Lastly, the electrochemical characterization with Cyclic Voltammetry (CV) proved that Fe3O4/MWCNT nanocomposites with iron sands as the starting materials have high sensitivity and serve as excellent electron transfer materials. Based on the results of the research, the Fe3O4/MWCNT nanocomposites from iron sands are much recommended for electrochemical sensor.The aim of this research is producing the electrochemical sensor, especially for working electrodes based on the nanocomposites of multi-walled carbon nanotube (MWCNT) and magnetite (Fe3O4) nanoparticles from iron sands. The sonochemical method by ultrasonic horn was successfully used for the synthesis of the nanocomposites. The characterizations of the sample were conducted via X-Ray Diffractometer (XRD), Fourier Transform Infra-Red (FTIR) Spectrometer, Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Brunauer-Emmett-Teller (BET) method for surface area, Vibrating Sample Magnetometer (VSM) and Cyclic Voltammetry (CV). The analysis of X-Ray Diffraction (XRD) pattern showed two phases of crystalline, namely MWCNT and Fe3O4, peak of MWCNT comes from (002) plan while peaks of Fe3O4 come from (2 2 0), (3 1 1), (4 0 0), (4 2 2), (5 1 1), and (4 4 0) plans. From XRD data, MWCNT has a hexagonal structure and Fe3O4 has inverse spinel cubic structure, respectively. The FTIR spectra revea...

pH Influences on Optical Absorption of Anthocyanin from Black Rice as Sensitizer for Dye Sensitized Solar Cell TiO2 Nanoparticles

Natural dyes extracted from black rice are used as sensitizer for dye sensitized solar cell. The anthocyanin extracted with various pH in acidic and neutral coditions. Preparation of fotolectrode TiO2 film using doctor blade method and resulting average grain size 33,9 nm using X-Ray Diffractometer. Characterization of morphology and cross-section film TiO2 is confirmed by Scanning Electron microscopy (SEM). Optical absorption using UV-Visible Spectroscopy to obtain spectrum absorbance of anthocyanin in various pH. The current-voltage (J-V) characterization shows the performance DSSC have a match relation to the optical absorption. The best absorption of anthocyanin obtained at pH 6 as well as conversion efficiency reaches 2.26% at this pH condition.

Charge Transfer Dynamics of Highly Efficient Cyanidin-3-O- Glucoside Sensitizer for Dye-Sensitized Solar Cells

This paper reports the novel efficiency achievement of black rice-based natural dye- sensitized solar cells. The higher dye concentration, the longer dye extraction as well as dye immersion onto a TiO2 film, and the co-adsorption addition are key strategies for improved-cell performance compared to the highest previous achievement. The black rice dye containing 1.38 mM cyanidin-3-O-glucoside has been extracted without purification for 3 weeks at dark condition and room temperature. The anatase TiO2 photoanode was dipped into dye solution within 4 days. Its electrode was firmly sealed to be a cell and was filled by I-/I3- electrolyte using vacuum technique. As a result, the overall solar-to-energy conversion efficiency was 1.49% at AM 1.5 illumination (100 mW.cm-2). The voltametric analysis has reported the interfacial electronic band edges of TiO2-Dye-Electrolyte. Furthermore, electrochemical impedance spectroscopy has shown the kinetic of interfacial electron transfer dynamics among TiO2-dye-electrolyte. The cell has the transfer resistance (Rt) of 12.5 ω, the recombination resistance (Rr) of 266.8 ω, effective electron diffusion coefficients (Dn) of 1.4 × 10-3 cm2/s, Dye-TiO2 effective electron transfer (τd) of 26.6 μs, effective diffusion length (Ln)of 33.78 μm, chemical capacitance (Cμ) of 12.43 μF, and electron lifetime (τn) of 3.32 ms.

Electrical Impedance Tomography in Rectangular Object Using Data Collection System Based on Absolute Boundary Potential Measurement

One of the problems in Electrical Impedance Tomography (EIT) is the ill-possed problem occurred in the reconstruction process. Beside addition of the data number and developing of reconstruction method, using of data collection system also determine the quality of image produced. This study is aimed to propose an absolute boundary potential to adjacent method. The result showed that adjacent method with absolute boundary potential give the better result compared to the use of relative boundary potential.