Suzanne H.P.M. de Winter

Oil-filled polymer microcapsules for ultrasound-mediated delivery of lipophilic drugs

The use of ultrasound contrast agents as local drug delivery systems continues to grow. Current limitations are the amount of drug that can be incorporated as well as the efficiency of drug release upon insonification. This study focuses on the synthesis and characterisation of novel polymeric microcapsules for ultrasound-triggered delivery of lipophilic drugs. Microcapsules with a shell of fluorinated end-capped poly(L-lactic acid) were made through pre-mix membrane emulsification and contained, apart from a gaseous phase, different amounts of hexadecane oil as a drug-carrier reservoir. Mean number weighted diameters were between 1.22 microm and 1.31 microm. High-speed imaging at approximately 10 million fames per second showed that for low acoustic pressures (1 MHz, 0.24 MPa) microcapsules compressed but remained intact. At higher diagnostic pressures of 0.51 MPa, microcapsules cracked, thereby releasing the encapsulated gas and model lipophilic drug. Using conventional ultrasound B-mode imaging at a frequency of 2.5 MHz, a marked enhancement of scatter intensity over a tissue-mimicking phantom was observed for all differently loaded microcapsules. The partially oil-filled microcapsules with high drug loads and well-defined acoustic activation thresholds have great potential for ultrasound-triggered local delivery of lipophilic drugs under ultrasound image-guidance.

High efficiency polymer LEDs: triplets and novel devices

We present results and a discussion of highly efficient polymer Light-Emitting Diodes (polymer LEDs, PLEDs). The external quantum efficiency in current standard devices reaches up to 2-4% only. We have explored two routes to enhance this value. In the first route, PEDOT/PSS is replaced with a novel anode or hole injection layer. The efficiency with some Light Emitting Polymers (LEP) is improved significantly, resulting in an efficacy of 35 cd/A for a yellow emitting poly-(para-phenylene-vinylene) and 20 cd/A for a blue emitting poly-(spirobifluorene). We attribute the major improvement compared to standard devices, where about 10 and 5 cd/A are obtained, respectively, to a combination of improved exciton formation efficiency and light out-coupling efficiency, and to less quenching of the radiative decay under actual device operating conditions. In the second route, we developed a new host polymer with high triplet energy such that transition metal-based green-emitting phosphorescent dyes can be used without significant back transfer of triplet excitons to the polymer host. First results using this system showed about 25 cd/A using a soluble green Ir-based emitter. Importantly, all data are obtained in a standard two-layer device of a hole transport/injection layer and the LEP.

Technology and materials for full-color polymer light-emitting displays

The status of the development of full-color polymer light emitting diodes will be presented. The focus of current materials research is on state-of-the-art red, green, and blue light-emitting polymers (LEP) with high efficiency, optimum color points, low driving voltages and long lifetimes in devices. A general overview of the progress of red, green and blue LEP lifetimes and efficiencies will be given and compared to requirements for both full-color passive and active matrix-displays for mobile display applications. Further, the status of ink-jet printing of LEPs for the industrialization of full-color displays will be discussed, and a comparison of the performance of spin coated and inkjet printed devices will be presented. In addition, two material-related topics studied recently will be discussed; namely, the lifetime of blue light-emitting devices correlated to processing, anodes, cathodes and the blue polymers themselves, and second, the consequences of pulsed-driving schemes on efficiency and lifetime.

Thin-film flexible barriers for PV applications and OLED lighting

To protect organic flexible devices from the ambient, they have to be encapsulated. Depending on the application in mind (OLED lighting, PV) different thin-film encapsulation methodology can be chosen. Each encapsulation process has different requirements and fabrication process freedom might be restricted, for example by mechanical reliability requirements or the total cost of the end product. Here we will show our recent investigations into different thin-film barriers with respect to their application and the route to production.

P‐262: Printing Technologies for Flexible OLEDs

There is a large potential market for flexible OLED Lighting and signage, however this requires to scale up present laboratory processes towards low cost, large area printing technologies. This presentation will compare lab scale made spin coated OLEDs on glass with ink jet and gravure printed OLEDs on foils.