Thiago Pinotti Segato

Capacitively coupled contactless conductivity detection on microfluidic systems—ten years of development

The use of capacitively coupled contactless conductivity detection (C4D) on miniaturized systems has increased considerably over the last few years. Since the first report, 10 years ago, several advances on the detection cell geometry, strategies for increasing the sensitivity and a wide range of applications have been reported. This review intends to cover the main features related to the instrumental setup of this detection method for analytical and bioanalytical assays on microfluidic chips.

A rapid and reliable bonding process for microchip electrophoresis fabricated in glass substrates

In this report, we describe a rapid and reliable process to bond channels fabricated in glass substrates. Glass channels were fabricated by photolithography and wet chemical etching. The resulting channels were bonded against another glass plate containing a 50‐μm thick PDMS layer. This same PDMS layer was also used to provide the electrical insulation of planar electrodes to carry out capacitively coupled contactless conductivity detection. The analytical performance of the proposed device was shown by using both LIF and capacitively coupled contactless conductivity detection systems. Efficiency around 47 000 plates/m was achieved with good chip‐to‐chip repeatability and satisfactory long‐term stability of EOF. The RSD for the EOF measured in three different devices was ca. 7%. For a chip‐to‐chip comparison, the RSD values for migration time, electrophoretic current and peak area were below 10%. With the proposed approach, a single chip can be fabricated in less than 30 min including patterning, etching and sealing steps. This fabrication process is faster and easier than the thermal bonding process. Besides, the proposed method does not require high temperatures and provides excellent day‐to‐day and device‐to‐device repeatability.

Glass/PDMS hybrid microfluidic device integrating vertically aligned SWCNTs to ultrasensitive electrochemical determinations

This communication reports a promising platform for rapid, simple, direct, and ultrasensitive determination of serotonin. The method is related to integration of vertically aligned single-walled carbon nanotubes (SWCNTs) in electrochemical microfluidic devices. The required microfabrication protocol is simple and fast. In addition, the nanomaterial influenced remarkably the obtained limit-of-detection (LOD) values. Our system achieved a LOD of 0.2 nmol L(-1) for serotonin, to the best of our knowledge one of the lowest values reported in the literature.

Determination of glyphosate and AMPA on polyester-toner electrophoresis microchip with contactless conductivity detection

This paper reports a method for rapid, simple, direct, and reproducible determination of glyphosate and its major metabolite aminomethylphosphonic acid (AMPA). The platform described herein uses polyester‐toner microchips incorporating capacitively coupled contactless conductivity detection and electrophoresis separation of the analytes. The polyester‐toner microchip presented 150 μm‐wide and 12 μm‐deep microchannels, with injection and separation lengths of 10 and 40 mm long, respectively. The best results were obtained with 320 kHz frequency, 4.5 Vpp excitation voltage, 80 mmol/L CHES/Tris buffer at pH 8.8, injection in −1.0 kV for 7 s, and separation in −1.5 kV. RSD values related to the peak areas for glyphosate and AMPA were 1.5 and 3.3% and 10.1 and 8.6% for intra‐ and interchip assays, respectively. The detection limits were 45.1 and 70.5 μmol/L, respectively, without any attempt of preconcentration of the analytes. Finally, the method was applied to river water samples in which glyphosate and AMPA (1.0 mmol/L each) were added. The recovery results were 87.4 and 83.7% for glyphosate and AMPA, respectively. The recovery percentages and LOD values obtained here were similar to others reported in the literature.

Paper-Based Microfluidics Immunoassay for Detection of Canine Distemper Virus

Paper-based devices present low-cost and are versatile, making them very attractive for clinical analysis. To manufacture those devices wax patterns are printed on paper surface and upon heating the wax permeates through the entire thickness of the paper, creating hydrophobic barriers that delimit test areas. Antibodies produced in rabbits against canine distemper virus (CDV) were physically adsorbed on the surface of gold nanoparticles (AuNPs) and incubated with CDV viral antigens, forming the immunocomplex. Anti-CDV antibodies were immobilized into the microchannels by physical adsorption, forming the test region. The test solution containing conjugated AuNPs was applied at the bottom of the microchannel and it was eluted with a phosphate buffer solution 0.01 M pH 7.4. When the solution containing the AuNPs reached the test zone the recognition of antigens contained on the immunocomplex occurred with the consequent development of a red line, which represents a positive outcome for the test. This method demonstrated the success of physical immobilization of antibodies on AuNPs and the physical immobilization of antibodies on cellulose’s surface. This colorimetric assay brings simplicity and versatility to clinical analyses, presenting potential for CDV diagnosis.