Tirunelveli S. Sriram

Package architecture and component design for an implanted neural stimulator with closed loop control

An implanted neural stimulator with closed loop control requires electrodes for stimulation pulses and recording neuron activity. Our system features arrays of 64 electrodes. Each electrode can be addressed through a cross bar switch, to enable it to be used for stimulation or recording. This electrode switch, a bank of low noise amplifiers with an integrated analog to digital converter, power conditioning electronics, and a communications and control gate array are co-located with the electrode array in a 14 millimeter diameter satellite package that is designed to be flush mounted in a skull burr hole. Our system features five satellite packages connected to a central hub processor-controller via ten conductor cables that terminate in a custom designed, miniaturized connector. The connector incorporates features of high reliability, military grade devices and utilizes three distinct seals to isolate the contacts from fluid permeation. The hub system is comprised of a connector header, hermetic electronics package, and rechargeable battery pack, which are mounted on and electrically interconnected by a flexible circuit board. The assembly is over molded with a compliant silicone rubber. The electronics package contains two antennas, a large coil, used for recharging the battery and a high bandwidth antenna that is used to download data and update software. The package is assembled from two machined alumina pieces, a flat base with brazed in, electrical feed through pins and a rectangular cover with rounded corners. Titanium seal rings are brazed onto these two pieces so that they can be sealed by laser welding. A third system antenna is incorporated in the flexible circuit board. It is used to communicate with an externally worn control package, which monitors the health of the system and allows both the user and clinician to control or modify various system function parameters.

An implantable, designed-for-human-use peripheral nerve stimulation and recording system for advanced prosthetics

Complex suture prostheses that deliver sensory and position feedback require a more sophisticated integration with the human user. Here a micro-size active implantable system that provides many-degree-of-freedom neural feedback in both sensory stimulation and motor control is shown, as one potential human-use solution in DARPAs HAPTIX program. Various electrical and mechanical challenge and solutions in meeting both sensory /motor performance as well as ISO 14708 FDA-acceptable human use in an aspirin-size active implementation are discussed.Complex suture prostheses that deliver sensory and position feedback require a more sophisticated integration with the human user. Here a micro-size active implantable system that provides many-degree-of-freedom neural feedback in both sensory stimulation and motor control is shown, as one potential human-use solution in DARPAs HAPTIX program. Various electrical and mechanical challenge and solutions in meeting both sensory /motor performance as well as ISO 14708 FDA-acceptable human use in an aspirin-size active implementation are discussed.

High density penetrating electrode arrays for autonomic nerves

Electrode arrays for recording and stimulation in the central nervous system have enabled numerous advances in basic science and therapeutic strategies. In particular, micro-fabricated arrays with precision size and spacing offer the benefit of accessing single neurons and permit mapping of neuronal function. Similar advances are envisioned toward understanding the autonomic nervous system and developing therapies based on its modulation, but appropriate electrode arrays are lacking. Here, we present for the first time, a multi-channel electrode array suitable for penetration of peripheral nerves having diameters as small as 0.1mm, and demonstrate performance in vivo. These arrays have the potential to access multiple discrete nerve fibers in small nerves. We fabricated and characterized five-channel arrays and obtained preliminary recordings of activity when penetrating rat carotid sinus nerve. The electrodes were constructed using hybrid microfabrication processes. The individual electrode shafts are as small as 0.01mm in diameter and at its tip each has a defined site that is addressable via a standard electronic connector. In addition to acute in vivo results, we evaluate the device by electrochemical impedance spectroscopy. Having established the fabrication method, our next steps are to incorporate the arrays into an implantable configuration for chronic studies, and here we further describe concepts for such a device.

Ultra-high density packaging technology for injectable medical devices

Future implantable medical devices will be highly miniaturized and almost certainly leverage die-level electronics miniaturization and packaging. Here, an integrated ultra-high density packaging platform is proposed to enable a new class of medical devices. Dense modules are obtained by interconnecting existing ASICs and discrete components using a process which achieves the highest packaging densities available.