Toan Dinh

Graphite on paper as material for sensitive thermoresistive sensors

This paper reports on the thermoresistive properties of graphite on paper (GOP). A negative temperature coefficient of resistance (TCR) from −2900 to −4400 ppm K−1 was observed for the GOP. This negative and large TCR is attributed to an increase in the thermionic emission current over a low potential barrier with increasing temperature. The potential barrier was found to be 33 meV between the graphite grains. The paper also demonstrates the use of the GOP in a highly sensitive (0.83 mV (m s−1)−0.8 mW−1) GOP-based anemometer, indicating strong feasibility of using this material for low-cost and sensitive thermal sensing applications.

Charge transport and activation energy of amorphous silicon carbide thin film on quartz at elevated temperature

We report on the temperature dependence of the charge transport and activation energy of amorphous silicon carbide (a-SiC) thin films grown on quartz by low-pressure chemical vapor deposition. The electrical conductivity as characterized by the Arrhenius rule was found to vary distinctly under two activation energy thresholds of 150 and 205 meV, corresponding to temperature ranges of 300 to 450 K and 450 to 580 K, respectively. The a-SiC/quartz system displayed a high temperature coefficient of resistance ranging from −4,000 to −16,000 ppm/K, demonstrating a strong feasibility of using this material for highly sensitive thermal sensing applications.

Thermoresistive properties of p-type 3C–SiC nanoscale thin films for high-temperature MEMS thermal-based sensors

We report for the first time the thermoresistive property of p-type single crystalline 3C–SiC (p-3C–SiC), which was epitaxially grown on a silicon (Si) wafer, and then transferred to a glass substrate using a Focused Ion Beam (FIB) technique. A negative and relatively large temperature coefficient of resistance (TCR) up to −5500 ppm K−1 was observed. This TCR is attributed to two activation energy thresholds of 45 meV and 52 meV, corresponding to temperatures below and above 450 K, respectively, and a small reduction of hole mobility with increasing temperature. The large TCR indicates the suitability of p-3C–SiC for thermal-based sensors working in high-temperature environments.

Piezoresistive effect in p-type 3C-SiC at high temperatures characterized using Joule heating.

Cubic silicon carbide is a promising material for Micro Electro Mechanical Systems (MEMS) applications in harsh environ-ments and bioapplications thanks to its large band gap, chemical inertness, excellent corrosion tolerance and capability of growth on a Si substrate. This paper reports the piezoresistive effect of p-type single crystalline 3C-SiC characterized at high temperatures, using an in situ measurement method. The experimental results show that the highly doped p-type 3C-SiC possesses a relatively stable gauge factor of approximately 25 to 28 at temperatures varying from 300 K to 573 K. The in situ method proposed in this study also demonstrated that, the combination of the piezoresistive and thermoresistive effects can increase the gauge factor of p-type 3C-SiC to approximately 20% at 573 K. The increase in gauge factor based on the combination of these phenomena could enhance the sensitivity of SiC based MEMS mechanical sensors.

Piezoresistive effect of p-type silicon nanowires fabricated by a top-down process using FIB implantation and wet etching

The piezoresistive effect in silicon nanowires (SiNWs) has attracted a great deal of interest for NEMS devices. Most of the piezoresistive SiNWs reported in the literature were fabricated using the bottom up method or top down processes such as electron beam lithography (EBL). Focused ion beam (FIB), on the other hand, is more compatible with CMOS integration than the bottom up method, and is simpler and more capable of fabricating very narrow Si nanostructures compared to EBL and photolithography. Taking the advantages of FIB, this paper presents for the first time the piezoresistive effect of p-type SiNWs fabricated using focused ion beam implantation and wet etching. The SiNWs were locally amorphized by Ga+ ion implantation, selectively wet-etched, and thermally annealed at 700 °C. A relatively large gauge factor of approximately 47 was found in the annealed SiNWs, indicating the potential of using the piezoresistive effect in top-down fabricated SiNWs for developing NEMS sensors.

Piezoresistive effect of p-type single crystalline 3C–SiC on (111) plane

This paper presents for the first time the effect of strain on the electrical conductivity of p-type single crystalline 3C–SiC grown on a Si (111) substrate. 3C–SiC thin film was epitaxially formed on a Si (111) substrate using the low pressure chemical vapor deposition process. The piezoresistive effect of the grown film was investigated using the bending beam method. The average longitudinal gauge factor of the p-type single crystalline 3C–SiC was found to be around 11 and isotropic in the (111) plane. This gauge factor is 3 times smaller than that in a p-type 3C–SiC (100) plane. This reduction of the gauge factor was attributed to the high density of defects in the grown 3C–SiC (111) film. Nevertheless, the gauge factor of the p-type 3C–SiC (111) film is still approximately 5 times higher than that in most metals, indicating its potential for niche mechanical sensing applications.

Thermoresistive Effect for Advanced Thermal Sensors: Fundamentals, Design Considerations, and Applications

Microelectromechanical systems sensors have been intensively developed utilizing various physical concepts, such as piezoresistive, piezoelectric, and thermoresistive effects. Among these sensing concepts, the thermoresistive effect is of interest for a wide range of thermal sensors and devices, thanks to its simplicity in implementation and high sensitivity. The effect of temperature on the electrical resistance of some metals and semiconductors has been thoroughly investigated, leading to the significant growth and successful demonstration of thermal-based sensors, such as temperature sensors, convective accelerometers and gyroscopes, and thermal flow sensors. In this paper, we review the fundamentals of the thermoresistive effect in metals and semiconductors. We also discuss the influence of design and fabrication parameters on the thermoresistive sensitivity. This paper includes several desirable features of thermoresistive sensors and recent developments in these sensors are summarized. This review provides insights into how it is affected by various parameters, and useful guidance for industrial designers in terms of high sensitivity and linearity and fast response. [2017-0022]

Environment-friendly carbon nanotube based flexible electronics for noninvasive and wearable healthcare

Flexible and stretchable electronics have a wide variety of wearable applications in portable sensors, flexible electrodes/heaters, flexible circuits and stretchable displays. Spinnable carbon nanotubes (CNTs) constructed on flexible substrates are potential materials for wearable sensing applications owing to their high thermal and electrical conductivity, low mass density and excellent mechanical properties. Here, we demonstrate a wearable thermal flow sensor for healthcare using lightweight, high strength, flexible CNT yarns as hotwires, pencil graphite as electrodes, and lightweight, recyclable and biodegradable paper as flexible substrates, without using any toxic chemicals. The CNT-based sensor which could be utilized to monitor respiratory diseases is comfortably affixed to human skin and detects real-time human respiration. We also successfully demonstrate the temperature detecting functionality integrated in the same sensor, which can measure body temperature using a non-contact mode. The results indicate that the CNT yarn can be used to develop a wide range of environment-friendly, low-cost and lightweight paper-based flexible devices for wearable applications in temperature and respiratory monitoring, and personal healthcare.

The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices

This communication reports for the first time, the impact of device geometry on the stress-dependent offset voltage of single crystal p-type 3C–SiC four terminal devices. Single crystal p-type 3C–SiC(100) was grown by low pressure chemical vapor deposition and three different device geometries (cross, rectangle and square) were fabricated using the conventional photolithography and dry etching processes. It was observed that the stress-dependent offset voltage of the devices strongly depends upon the device geometry and it can be increased by almost 100% by just selecting the appropriate device geometry. We also found that as the device is rotated within the (100) crystal plane its stress sensitivity varies from ≈0 to 9 × 10−11 Pa−1.

Flexible and multifunctional electronics fabricated by a solvent-free and user-friendly method

Flexible and multifunctional electronic devices have been proven to show potential for various applications including human-motion detection and wearable thermal therapy. The key advantages of these systems are (1) highly stable, sensitive and fast-response devices, (2) fabrication of macroscale devices on flexible substrates, and (3) integrated (lab-on-chip) and multifunctional devices. However, their fabrication commonly requires toxic solvents, as well as time-consuming and complex processes. Here, we demonstrate the low-cost, rapid-prototyping and user-friendly fabrication of flexible transducers using recyclable, water-resistant poly(vinyl chloride) films as a substrate, and ubiquitously available pencil graphite as a functional layer without using any toxic solvents or additional catalysts. The flexible heaters showed good characteristics such as fast thermal response, good thermostability (low temperature coefficient of resistance) and low power consumption. The heaters with their capability of perceiving human motion were shown to be effective. The proof of concept of other functional devices such as vibration-based droplet sensors and drag-force air flow sensors was also demonstrated. Results from this study indicate that a wide range of electronic devices fabricated from the environmental-friendly material by this simple and user-friendly approach could be utilized for cost-effective, flexible and low power consuming thermal therapy, health monitoring systems and other real-time monitoring devices without using any toxic chemicals or advanced processes.