Tohru Imai

Long-term effects of prostaglandin E2 on the mineralization of a clonal osteoblastic cell line (MC3T3-E1)

Prostaglandin (PG) E2 is thought to be a mediator of the effect of mechanical stress on bone formation, but its effects on osteoblasts have not yet been fully described. Here, the effects of the continuous application of PGE2 and indomethacin, an inhibitor of prostaglandin G/H synthase (cyclo-oxygenase), on the proliferation, differentiation and mineralization of a clonal osteoblastic cell line, MC3T3-E1, were investigated. The cells were cultured in media with either a high (1 microg/ml) or a low (1 ng/ml) concentration of PGE2, with indomethacin (1 microg/ml) and, as a control, with neither agent. The effects of PGE2 and indomethacin were assessed quantitatively. Indomethacin and a high concentration of PGE2 increased the total protein compared to the control and low-PGE2 cultures. 7 days after confluence, alkaline phosphatase (ALP) activity within the cells and extracellular matrices increased. This increase was highest with indomethacin and lowest with a high concentration of PGE2. ALP activity also increased in the medium, but only 21 days after confluence; the effects of the agents were similar to those on the cells and matrices. The accumulation of calcium, inorganic phosphate and hydroxyproline was highest with indomethacin. PGE2 production was at its maximum when the cells were at confluence and was inhibited by indomethacin. Specific [3H]PGE2 binding to the microsomal fraction of the cell was also measured to examine the expression of the PGE2 receptor. The amount of [3H]PGE2 binding per mg of protein was highest at confluence, then decreased and again increased in the mineralizing stage. These results suggest that indomethacin increases ALP activity and the accumulation of mineralized tissue in MC3T3-E1 cells, presumably by inhibiting the production of PGE2. PGE2 could signal the suppression of mineralization as early as confluence.

Mechanical properties and aesthetics of FRP orthodontic wire fabricated by hot drawing

The FRP wires 0.5 mm in diameter with a multiple fiber structure were fabricated by drawing the fiber polymer complex at 250 degrees C for an esthetic, transparent orthodontic wire. Biocompatible CaO-P2O5-SiO2-Al2O3 (CPSA) glass fibers of 8-20 microm in diameter were oriented unidirectionally in the longitudinal direction in PMMA matrix. The mechanical properties were investigated by 3-point flexural test. The FRP wire showed sufficient strength and a very good elastic recovery after deformation. Youngs modulus and the flexural load at deflection 1 mm were nearly independent of the fiber diameter and linearly increased with the fiber fraction. The dependence on fiber fraction obeys well the rule of mixture. This FRP wire could cover the range of strength corresponding to the conventional metal orthodontic wires from Ni-Ti used in the initial stage of orthodontic treatments to Co-Cr used in the final stage by changing the volume ratio of glass fibers with the same external diameter. The estheticity in external appearance was excellent. Thus the new FRP wire can satisfy both mechanical properties necessary for an orthodontic wire and enough estheticity, which was not possible for the conventional metal wire.

The fabrication and properties of aesthetic FRP wires for use in orthodontics

Transparent or translucent fibre-reinforced polymeric wires have been produced in an attempt to reproduce the mechanical properties of the metallic wires in current use in orthodontics. Two methods were employed: mould polymerization, and hot-drawing. Both methods produced wires of 0.5 mm diameter. Two polymers were investigated, poly(methyl methacrylate) and epoxy resin, and these were filled with either long silane-coated alumina fibres or fibres made from CPSA glass. Whilst mould-polymerized wires showed a linear increase in Youngs modulus with fibre content, they did not obey the rule of mixtures. However, the hot-drawn wires did, and they also demonstrated the rigidity, strength and good elastic recovery needed for use in orthodontics.