Vamegh Rasouli

A Bonded Particle Model Simulation of Shear Strength and Asperity Degradation for Rough Rock Fractures

Different failure modes during fracture shearing have been introduced including normal dilation or sliding, asperity cut-off and degradation. Attempts have been made to study these mechanisms using analytical, experimental and numerical methods. However, the majority of the existing models simplify the problem, which leads to unrealistic results. With this in mind, the aim of this paper is to simulate the mechanical behaviour of synthetic and rock fracture profiles during direct shear tests by using the two-dimensional particle flow computer code PFC2D. Correlations between the simulated peak shear strength and the fracture roughness parameter DR1 recently proposed by Rasouli and Harrison (2010) are developed. Shear test simulations are carried out with PFC2D and the effects of the geometrical features as well as the model micro-properties on the fracture shear behaviour are studied. The shear strength and asperity degradation processes of synthetic profiles including triangular, sinusoidal and randomly generated profiles are analysed. Different failure modes including asperity sliding, cut-off, and asperity degradation are explicitly observed and compared with the available models. The DR1 parameter is applied to the analysis of synthetic and rock fracture profiles. Accordingly, correlations are developed between DR1 and the peak shear strength obtained from simulations and by using analytical solutions. The results are shown to be in good agreement with the basic understanding of rock fracture shear behaviour and asperity contact degradation.

Test Design and Sample Preparation Procedure for Experimental Investigation of Hydraulic Fracturing Interaction Modes

Abstract Hydraulic fracturing is a complex operation which is influenced by several factors including the formation properties, state of stresses in the field, injecting fluid and pumping rate. Before carrying out the expensive fracturing operation in the field, it would be useful to understand the effect of various parameters by conducting physical experiments in the laboratory. Also, laboratory experiments are valuable for validating numerical simulations. For this purpose, laboratory experiments may be conducted on synthetically made samples to study the effect of various parameters before using real rock samples, which may not be readily available. To simulate the real stress conditions in the field, experiments need to be conducted on cube-shaped samples on which three independent stresses can be applied. The hydro-mechanical properties of a sample required for modelling purposes and the design of a scaled hydraulic fracturing test in the laboratory can be estimated by performing various laboratory experiments on cylindrical plugs. The results of laboratory experiments are scaled to field operation by applying scaling laws. In this paper, the steps to prepare a cube-shaped mortar sample are explained. This follows a review of the sample set-up procedure in a true tri-axial stress cell for hydraulic fracturing experiments. Also, the minimum tests on cylindrical plugs required to estimate the hydro-mechanical properties of the rock sample are explained. To simulate the interaction mode when a hydraulic fracture approaches an interface in the laboratory, the procedure for producing samples with parallel artificial fracture planes is explained in this paper. The in-fill material and the angle of fracture planes were changed in different samples to investigate the effect of interface cohesion and the angle of approach on the interaction mechanism.

Mechanical and Elastic Properties of Transversely Isotropic Slate

Planes of weakness like schistosity and foliation affect the strength and deformational behaviors of rocks. In this paper, an attempt has been made to study the elastic and strength behavior of slate rocks obtained from foundation of Sardasht dam site in Iran. Wet and dry specimens with different orientation of foliation were evaluated under uniaxial, triaxial, and Brazilian tests. According to the results obtained, slate mechanically pronounced U-shaped anisotropy in uniaxial and triaxial compression tests. In addition, the degree of anisotropy for the slates tested in current study was relatively high, showing the effect of foliation plane on strength and elastic parameters. It was concluded that stiffness of the samples decrease as the angle of anisotropy reaches 30–40°. This change was more pronounced for wet comparing to dry samples. However, the tensile strength obtained during Brazilian tests indicated that there is no apparent relationship between angle of anisotropy and tensile strength. However, increasing the water saturation decreased the tensile strength of the samples. The calculated elastic moduli referring to different anisotropy angles could be valuable for the design of various engineering structures in planar textured rock masses.

Geomechanical characteristics of gas shales: A case study in the North Perth basin

Abstract Gas shales are one type of unconventional reservoirs which have attracted significant attention for gas production in recent years. Gas production from very tight shales requires employment of hydraulic fracturing as a stimulation technique. To design hydraulic fracture operation the mechanical properties of the targeted and surrounding formations should be estimated. Also, the magnitude and orientation of in situ stresses in the field need to be known to estimate the fracture initiation and propagation pressures. This study focuses on gas shale characteristics in the North Perth Basin and uses data corresponding to well Arrowsmith-2 (AS-2) which is the first dedicated shale gas well drilled in Western Australia. A log-based analysis was used to build the rock mechanical model (RMM). The RMM results were used to set up a hydraulic fracturing laboratory experiment. The test was done in the presence of three principal stresses to mimic the real field stress conditions. The test results include the pressure–time curve which was used to estimate the initiation and propagation pressure at that depth. The results were used to draw some practical conclusions related to hydraulic fracturing operation in the field.

A Laboratory Shear Cell Used for Simulation of Shear Strength and Asperity Degradation of Rough Rock Fractures

Different failure modes during fracture shearing have been introduced including dilation, sliding, asperity cut-off and degradation. Several laboratory studies have reported the complexity of these failure modes during shear tests performed under either constant normal load (CNL) or constant normal stiffness (CNS) conditions. This paper is concerned with the mechanical behaviour of synthetic fractures during direct shear tests using a modified shear cell and related numerical simulation studies. The modifications made to an existing true triaxial stress cell (TTSC) in order to use it for performing shear tests under CNL conditions are presented. The large loading capacity and the use of accurate hydraulic pumps capable of applying a constant shear velocity are the main elements of this cell. Synthetic mortar specimens with different fracture surface geometries are tested to study the failure modes, including fracture sliding, asperity degradation, and to understand failure during shearing. A bonded particle model of the direct shear test with the PFC2D particle flow code is used to mimic the tests performed. The results of a number of tests are presented and compared with PFC2D simulations. The satisfactory results obtained both qualitatively and quantitatively are discussed.

Modified Reinshaw and Pollard Criteria for a Non-Orthogonal Cohesive Natural Interface Intersected by an Induced Fracture

Abstract Hydraulic fracturing is a widely used stimulation method to enhance the productivity of unconventional resources. The hydraulic fracturing operation in naturally fractured reservoirs or when it is expected to intersect a natural interface, such as an interbed is subjected to complexity. The induced fracture may cross, get arrested by or open the fracture plane upon its arrival at the natural interface. Besides other parameters, this depends on the natural interface mechanical properties, including the cohesion and friction angle of the interface. Several analytical criteria have been developed to predict the interaction mechanism of induced and natural fracture. While these analytical solutions have been developed based on some simplified assumptions, they can provide a good understanding of the effect of different parameters. The first part of this paper summarizes the available criteria for interaction of hydraulic and natural fractures. Important factors will be mentioned and illustrations will be given to present the limitations of each criterion. The second part discusses the development and validation of an extension to Renshaw and Pollard criterion in the form a single analytical formula for non-orthogonal cohesive fracture. This includes the contribution of the strength of the in-fill material to the bonding of the two sides of a fracture, hence its effect on the interaction mechanism. The proposed criterion was validated using published laboratory data. Finally, a methodology is proposed to help the design of interaction experiments in the laboratory, which can also be used for prediction of interaction mode in numerical simulations.

A modified empirical criterion for strength of transversely anisotropic rocks with metamorphic origin

A modified empirical criterion is proposed to determine the strength of transversely anisotropic rocks. In this regard, mechanical properties of intact anisotropic slate obtained from three different districts of Iran were taken into consideration. Afterward, triaxial rock strength criterion introduced by Rafiai was modified for transversely anisotropic rocks. The criterion was modified by adding a new parameter

A True Triaxial Stress Cell to Simulate Deep Downhole Drilling Conditions

\alpha