Vladimir Strezov

Influence of pyrolysis temperature on production and nutrient properties of wastewater sludge biochar.

The important challenge for effective management of wastewater sludge materials in an environmentally and economically acceptable way can be addressed through pyrolytic conversion of the sludge to biochar and agricultural applications of the biochar. The aim of this work is to investigate the influence of pyrolysis temperature on production of wastewater sludge biochar and evaluate the properties required for agronomic applications. Wastewater sludge collected from an urban wastewater treatment plant was pyrolysed in a laboratory scale reactor. It was found that by increasing the pyrolysis temperature (over the range from 300 °C to 700 °C) the yield of biochar decreased. Biochar produced at low temperature was acidic whereas at high temperature it was alkaline in nature. The concentration of nitrogen was found to decrease while micronutrients increased with increasing temperature. Concentrations of trace metals present in wastewater sludge varied with temperature and were found to primarily enriched in the biochar.

Agronomic properties of wastewater sludge biochar and bioavailability of metals in production of cherry tomato (Lycopersicon esculentum).

This work presents agronomic values of a biochar produced from wastewater sludge through pyrolysis at a temperature of 550 degrees C. In order to investigate and quantify effects of wastewater sludge biochar on soil quality, growth, yield and bioavailability of metals in cherry tomatoes, pot experiments were carried out in a temperature controlled environment and under four different treatments consisting of control soil, soil with biochar; soil with biochar and fertiliser, and soil with fertiliser only. The soil used was chromosol and the applied wastewater sludge biochar was 10tha(-1). The results showed that the application of biochar improves the production of cherry tomatoes by 64% above the control soil conditions. The ability of biochar to increase the yield was attributed to the combined effect of increased nutrient availability (P and N) and improved soil chemical conditions upon amendment. The yield of cherry tomato production was found to be at its maximum when biochar was applied in combination with the fertiliser. Application of biochar was also found to significantly increase the soil electrical conductivity as well as phosphorus and nitrogen contents. Bioavailability of metals present in the biochar was found to be below the Australian maximum permitted concentrations for food.

Thermal conversion of elephant grass (Pennisetum Purpureum Schum) to bio-gas, bio-oil and charcoal

Elephant grass is an abundant, fast growing plant with significant potential as a renewable energy source and for conversion to higher calorific value fuels. This work investigates thermal conversion of elephant grass to bio-gas, bio-oil and charcoal under two heating rates of 10 and 50 degrees C/min. The energy required to pyrolyse elephant grass was evaluated using computer aided thermal analysis technique, while composition of the resultant bio-gas and bio-oil products were monitored with gas chromatographic and mass spectroscopic techniques. At 500 degrees C, the bio-gas compounds consisted primarily of CO2 and CO with small amounts of methane and higher hydrocarbon compounds. The heat of combustion of the bio-gas compounds was estimated to be 3.7-7.4 times higher than the heat required to pyrolyse elephant grass under both heating rates, which confirms that the pyrolysis process can be self-maintained. Faster heating rate was found to increase the amount of liquid products by 10%, while charcoal yields remained almost the same at 30%. The bio-oil mainly consisted of organic acids, phthalate esters, benzene compounds and amides. The amount of organic acids and benzene compounds were significantly reduced at 50 degrees C/min, while the yields of phthalate esters and naphthalene compounds increased. The difference in bio-oil composition with increased heating rate is believed to be associated with the reduction of the secondary reactions of pyrolysis, which are more pronounced under lower heating rate.

Properties of oil and char derived from slow pyrolysis of Tetraselmis chui

Pyrolysis of biomass is a means to industrially manufacture renewable oil and gas, in addition to biochar for soil amendment and long-term carbon fixation. In this work, oil and char derived from the slow pyrolysis of the unicellular marine diatom Tetraselmis chui are analysed using a variety of techniques. The pyrolytic oil fraction exhibits a wide variety of fatty acids, alkanes, alkenes, amides, aldehydes, terpenes, pyrrolidinines, phytol and phenols, with a high heating value (HHV) of 28 MJ/kg. The biochar produced has a HHV of 14.5 MJ/kg and reveals a number of properties that are potentially valuable from an agronomic point of view, including high cation exchange capacity (CEC), large concentration of N, and a low C:N ratio. The quantity of C in T. chui biochar that can be expected to stabilise in soil amounts to approximately 9%/wt of the original feedstock, leading to a potential net reduction in atmospheric CO(2).

Thermal processing of paper sludge and characterisation of its pyrolysis products

Paper sludge is a waste product from the paper and pulp manufacturing industry that is generally disposed of in landfills. Pyrolysis of paper sludge can potentially provide an option for managing this waste by thermal conversion to higher calorific value fuels, bio-gas, bio-oils and charcoal. This work investigates the properties of paper sludge during pyrolysis and energy required to perform thermal conversion. The products of paper sludge pyrolysis were also investigated to determine their properties and potential energy value. The dominant volatile species of paper sludge pyrolysis at 10 degrees C/min were found to be CO and CO(2), contributing to almost 25% of the paper sludge dry weight loss at 500 degrees C. The hydrocarbons (CH(4), C(2)H(4), C(2)H(6)) and hydrogen contributed to only 1% of the total weight loss. The bio-oils collected at 500 degrees C were primarily comprised of organic acids with the major contribution being linoleic acid, 2,4-decadienal acid and oleic acid. The high acidic content indicates that in order to convert the paper sludge bio-oil to bio-diesel or petrochemicals, further upgrading would be necessary. The charcoal produced at 500 degrees C had a calorific value of 13.3MJ/kg.

An Analysis of Citizen Science Based Research: Usage and Publication Patterns.

The use of citizen science for scientific discovery relies on the acceptance of this method by the scientific community. Using the Web of Science and Scopus as the source of peer reviewed articles, an analysis of all published articles on “citizen science” confirmed its growth, and found that significant research on methodology and validation techniques preceded the rapid rise of the publications on research outcomes based on citizen science methods. Of considerable interest is the growing number of studies relying on the re-use of collected datasets from past citizen science research projects, which used data from either individual or multiple citizen science projects for new discoveries, such as for climate change research. The extent to which citizen science has been used in scientific discovery demonstrates its importance as a research approach. This broad analysis of peer reviewed papers on citizen science, that included not only citizen science projects, but the theory and methods developed to underpin the research, highlights the breadth and depth of the citizen science approach and encourages cross-fertilization between the different disciplines.

Effect of heating rate on the thermal properties and devolatilisation of coal

The apparent specific heat of coal was measured by employing a computational calorimetric technique during continuous pyrolysis at heating rates of 10, 25 and 100°C min-1. For all of the examined heating rates, the apparent specific heat was found to be approximately 1.4 kJ kg-1 K-1 at room temperature. When the sample reached decomposition temperature (~410°C), the specific heat increased to 1.9 kJ kg-1 K-1. From this point, the apparent specific heat was greatly influenced by the coal reaction mechanism. For this purpose a detailed gas analysis was carried out for the three examined heating rates. It was found that with increased heating rates, the devolatilisation reactions were shifted to higher temperatures, as reflected in the measured apparent specific heat.

Biochar: An Emerging Panacea for Remediation of Soil Contaminants from Mining, Industry and Sewage Wastes

Abstract Mine tailings, waste rock piles, acid mine drainage, industrial wastewater, and sewage sludge have contaminated a vast area of cultivable and fallow lands, with a consequence of deterioration of soil and water quality and watercourses due to the erosion of contaminated soils for absence of vegetative cover. High concentrations of toxic elements, organic contaminants, acidic soils, and harsh climatic conditions have made it difficult to re-establish vegetation and produce crops there. Recently, a significant body of work has focussed on the suitability and potentiality of biochar as a soil remediation tool that increases seed emergence, soil and crop productivity, above ground biomass, and vegetation cover on mine tailings, waste rock piles, and industrial and sewage waste-contaminated soils by increasing soil nutrients and water-holding capacity, amelioration of soil acidity, and stimulation of microbial diversity and functions. This review addresses: i) the functional properties of biochar, and microbial cycling of nutrients in soil; ii) bioremediation, especially phytoremediation of mine tailings, industrial waste, sewage sludge, and contaminated soil using biochar; iii) impact of biochar on reduction of acid production, acid mine drainage treatment, and geochemical dynamics in mine tailings; and iv) treatment of metal and organic contaminants in soils using biochar, and restoration of degraded land.

Comparative Assessment of the Effect of Wastewater Sludge Biochar on Growth, Yield and Metal Bioaccumulation of Cherry Tomato

To investigate the potential effects of wastewater sludge and sludge biochar on growth, yield and metal bioaccumulation of cherry tomato (Lycopersicon esculentum L.), a pot experiment was carried out under greenhouse environment with three different treatments, control soil (CP), soil with wastewater sludge (SS) and soil with sludge biochar (SB), to reveal the comparative effect between the amendments of wastewater sludge and sludge biochar. The soil used for pot experiment was Chromosol. Wastewater sludge and sludge biochar produced through pyrolysis process at 550 °C were applied at 10 t ha−1. No significant difference was found in growth and production of cherry tomatoes between wastewater sludge and sludge biochar applications to the soil. The accumulation rates of metals in the fruits were lower in the treatment with sludge biochar than in the treatment with wastewater sludge. The study highlights the benefits of risk mitigation from toxic metal accumulation in fruits using wastewater sludge and sludge biochar as soil conditioners.

Mass and elemental distributions of atmospheric particles nearby blast furnace and electric arc furnace operated industrial areas in Australia

The improved understanding of mass and elemental distributions of industrial air particles is important due to their heterogeneous atmospheric behaviour and impact on human health and the environment. In this study, particles of different size ranges were collected from three sites in Australia located in the vicinity of iron and steelmaking industries and one urban background site with very little industrial influence. In order to determine the importance of the type of industrial activity on the urban atmospheric quality, the industrial sites selected in this study were in the close proximity to two blast furnace operated and one electric arc furnace based steelmaking sites. The chemical compositions of the collected air particles were analysed using the proton induced X-ray emission (PIXE) technique. This study revealed significantly higher metal concentrations in the atmospheric particles collected in the industrial sites, comparing to the background urban site, demonstrating local influence of the industrial activities to the air quality. The modality types of the particles were found to be variable between the mass and elements, and among elements in the urban and industrial areas indicating that the elemental modal distribution is as important as particle mass for particle pollution modelling. The highest elemental number distribution at all studied sites occurred with particle size of 0.1 μm. Iron was found as the main dominant metal at the industrial atmosphere in each particle size range. The industrial Fe fraction in the submicron and ultrafine size particles was estimated at up to 95% which may be released from high temperature industrial activities with the iron and steelmaking industries being one of the major contributors. Hence, these industrial elemental loadings can highly influence the atmospheric pollution at local urban and regional levels and are required to consider in the atmospheric modelling settings.