W. I. Milne

Growth process conditions of vertically aligned carbon nanotubes using plasma enhanced chemical vapor deposition

The growth of vertically aligned carbon nanotubes using a direct current plasma enhanced chemical vapor deposition system is reported. The growth properties are studied as a function of the Ni catalyst layer thickness, bias voltage, deposition temperature, C2H2:NH3 ratio, and pressure. It was found that the diameter, growth rate, and areal density of the nanotubes are controlled by the initial thickness of the catalyst layer. The alignment of the nanotubes depends on the electric field. Our results indicate that the growth occurs by diffusion of carbon through the Ni catalyst particle, which rides on the top of the growing tube.

Wideband-tuneable, nanotube mode-locked, fibre laser

Ultrashort-pulse lasers with spectral tuning capability have widespread applications in fields such as spectroscopy, biomedical research and telecommunications. Mode-locked fibre lasers are convenient and powerful sources of ultrashort pulses, and the inclusion of a broadband saturable absorber as a passive optical switch inside the laser cavity may offer tuneability over a range of wavelengths. Semiconductor saturable absorber mirrors are widely used in fibre lasers, but their operating range is typically limited to a few tens of nanometres, and their fabrication can be challenging in the 1.3-1.5 microm wavelength region used for optical communications. Single-walled carbon nanotubes are excellent saturable absorbers because of their subpicosecond recovery time, low saturation intensity, polarization insensitivity, and mechanical and environmental robustness. Here, we engineer a nanotube-polycarbonate film with a wide bandwidth (>300 nm) around 1.55 microm, and then use it to demonstrate a 2.4 ps Er(3+)-doped fibre laser that is tuneable from 1,518 to 1,558 nm. In principle, different diameters and chiralities of nanotubes could be combined to enable compact, mode-locked fibre lasers that are tuneable over a much broader range of wavelengths than other systems.

Flexible Electronics: The Next Ubiquitous Platform

Thin-film electronics in its myriad forms has underpinned much of the technological innovation in the fields of displays, sensors, and energy conversion over the past four decades. This technology also forms the basis of flexible electronics. Here we review the current status of flexible electronics and attempt to predict the future promise of these pervading technologies in healthcare, environmental monitoring, displays and human-machine interactivity, energy conversion, management and storage, and communication and wireless networks.

Microwave devices - Carbon nanotubes as cold cathodes

To communicate, spacecraft and satellites rely on microwave devices, which at present are based on relatively inefficient thermionic electron sources that require heating and cannot be switched on instantaneously. Here we describe a microwave diode that uses a cold-cathode electron source consisting of carbon nanotubes and that operates at high frequency and at high current densities. Because it weighs little, responds instantaneously and has no need of heating, this miniaturized electron source should prove valuable for microwave devices used in telecommunications.

Uniform patterned growth of carbon nanotubes without surface carbon

In order to utilize the unique properties of carbon nanotubes in microelectronic devices, it is necessary to develop a technology which enables high yield, uniform, and preferential growth of perfectly aligned nanotubes. We demonstrate such a technology by using plasma-enhanced chemical-vapor deposition (PECVD) of carbon nanotubes. By patterning the nickel catalyst, we have deposited uniform arrays of nanotubes and single free-standing aligned nanotubes at precise locations. In the PECVD process, however, detrimental amorphous carbon (a-C) is also deposited over regions of the substrate surface where the catalyst is absent. Here, we show, using depth-resolved Auger electron spectroscopy, that by employing a suitable deposition (acetylene, C2H2) to etching (ammonia, NH3) gas ratio, it is possible to obtain nanotube growth without the presence of a-C on the substrate surface.

Influence of ion energy and substrate temperature on the optical and electronic properties of tetrahedral amorphous carbon (ta-C) films

The properties of amorphous carbon (a-C) deposited using a filtered cathodic vacuum arc as a function of the ion energy and substrate temperature are reported. The sp3 fraction was found to strongly depend on the ion energy, giving a highly sp3 bonded a-C denoted as tetrahedral amorphous carbon (ta-C) at ion energies around 100 eV. The optical band gap was found to follow similar trends to other diamondlike carbon films, varying almost linearly with sp2 fraction. The dependence of the electronic properties are discussed in terms of models of the electronic structure of a-C. The structure of ta-C was also strongly dependent on the deposition temperature, changing sharply to sp2 above a transition temperature, T1, of ≈200 °C. Furthermore, T1 was found to decrease with increasing ion energy. Most film properties, such as compressive stress and plasmon energy, were correlated to the sp3 fraction. However, the optical and electrical properties were found to undergo a more gradual transition with the deposition...

Properties of carbon ion deposited tetrahedral amorphous carbon films as a function of ion energy

Ion energy, controlled by the substrate bias, is an important parameter in determining properties of films deposited by the filtered cathodic vacuum arc technique. The substrate bias determines the ion energy distribution of the growth species. The ion energy is varied, while keeping the other deposition conditions constant, in order to study the effect of ion energy on the film properties. The films were characterized by their optical and mechanical parameters using an ellipsometer, surface profilometer, optical spectrometer, and nanoindenter. Electron energy‐loss spectroscopy and Raman spectroscopy were used for structural analysis of the films.

A Critical Review of Glucose Biosensors Based on Carbon Nanomaterials: Carbon Nanotubes and Graphene

There has been an explosion of research into the physical and chemical properties of carbon-based nanomaterials, since the discovery of carbon nanotubes (CNTs) by Iijima in 1991. Carbon nanomaterials offer unique advantages in several areas, like high surface-volume ratio, high electrical conductivity, chemical stability and strong mechanical strength, and are thus frequently being incorporated into sensing elements. Carbon nanomaterial-based sensors generally have higher sensitivities and a lower detection limit than conventional ones. In this review, a brief history of glucose biosensors is firstly presented. The carbon nanotube and grapheme-based biosensors, are introduced in Sections 3 and 4, respectively, which cover synthesis methods, up-to-date sensing approaches and nonenzymatic hybrid sensors. Finally, we briefly outline the current status and future direction for carbon nanomaterials to be used in the sensing area.

Carbon nanotubes as field emission sources

Micro and nano-structurally rich carbon materials are alternatives to conventional metal/silicon tips for field emission sources. In particular, carbon nanotubes exhibit extraordinary field emission properties because of their high electrical conductivity, their high aspect ratio “whisker-like” shape for optimum geometrical field enhancement, and remarkable thermal stability. This paper will review the PECVD growth process, and the microfabrication techniques needed to produce well defined carbon nanotube based micro-electron sources for use in novel parallel e-beam lithography and high frequency microwave amplifier systems.

Field emission from dense, sparse, and patterned arrays of carbon nanofibers

We compare the field emission characteristics of dense (109 nanofibers/cm2), sparse (107 nanofibers/cm2), and patterned arrays (106 nanofibers/cm2) of vertically aligned carbon nanofibers on silicon substrates. The carbon nanofibers were prepared using plasma-enhanced chemical vapor deposition of acetylene and ammonia gases in the presence of a nickel catalyst. We demonstrate how the density of carbon nanofibers can be varied by reducing the deposition yield through nickel interaction with a diffusion layer or by direct lithographic patterning of the nickel catalyst to precisely position each nanofiber. The patterned array of individual vertically aligned nanofibers had the most desirable field emission characteristics, highest apparent field enhancement factor, and emission site density.