Wen Qiao

High performance organic distributed Bragg reflector lasers fabricated by dot matrix holography

We report distributed Bragg reflector (DBR) polymer lasers fabricated using dot matrix holography. Pairs of distributed Bragg reflector mirrors with variable mirror separations are fabricated and a novel energy transfer blend consisting of a blue-emitting conjugated polymer and a red-emitting one is spin-coated onto the patterned substrate to complete the device. Under optical pumping, the device emits sing-mode lasing around 622 nm with a bandwidth of 0.41 nm. The working threshold is as low as 13.5 μJ/cm² (~1.68 kW/cm²) and the measured slope efficiency reaches 5.2%. The distributed feedback (DFB) cavity and the DBR cavity resonate at the same lasing wavelength while the DFB laser shows a much higher threshold. We further show that flexible DBR lasers can be conveniently fabricated through the UV-imprinting technique by using the patterned silica substrate as the mold. Dot matrix holography represents a versatile approach to control the number, the size, the location and the orientation of DBR mirrors, thus providing great flexibility in designing DBR lasers.

Toward Scalable Flexible Nanomanufacturing for Photonic Structures and Devices

Continuous and scalable nanopatterning over flexible substrates is highly desirable for both commercial and scientific interests, but is difficult to realize with traditional photolithographic processes. The recent advancements in nanofabrication methodologies enable light management with photonic structures on flexible materials, providing an increasingly popular strategy to control the light harvesting in the optoelectronic devices of photovoltaics, and in organic and inorganic light-emitting diodes. Here, the current status of nanopatterning technologies for the fabrication of optoelectronic devices is summarized. Scalable nanopatterning technologies for nanomanufacturing on flexible materials are emphasized. Critical challenges in various patterning techniques when considering the resolution, scalability, processing throughput, and the use of masks and resists are addressed. The integration of flexible nanopatterned substrates with light manipulation in organic optoelectronic devices is also discussed; this enables the control of light flux and spectra. Finally, potential development directions are highlighted.

Dielectric-based subwavelength metallic meanders for wide-angle band absorbers.

We propose nano-meanders that can achieve wide-angle band absorption in visible regime. The nano-meander consists of a subwavelength dielectric grating covered by continuous ultra-thin Aluminum film (less than one tenth of the incident wavelength). The excited photonic resonant modes, such as cavity mode, surface plasmonic mode and Rayleigh-Wood anomaly, are discussed in detail. Nearly total resonant absorption due to funneling mechanism in the air nano-groove is almost invariant with large incident angle in transverse magnetic polarization. From both the structural geometry and the nanofabrication point of view, the light absorber has a very simple geometrical structure and it is easy to be integrated into complex photonic devices. The highly efficient angle-robust light absorber can be potential candidate for a range of passive and active photonic applications, including solar-energy harvesting as well as producing artificial colors on a large scale substrate.

Efficient fabrication method of nano-grating for 3D holographic display with full parallax views.

Without any special glasses, multiview 3D displays based on the diffractive optics can present high resolution, full-parallax 3D images in an ultra-wide viewing angle. The enabling optical component, namely the phase plate, can produce arbitrarily distributed view zones by carefully designing the orientation and the period of each nano-grating pixel. However, such 3D display screen is restricted to a limited size due to the time-consuming fabricating process of nano-gratings on the phase plate. In this paper, we proposed and developed a lithography system that can fabricate the phase plate efficiently. Here we made two phase plates with full nano-grating pixel coverage at a speed of 20 mm2/mins, a 500 fold increment in the efficiency when compared to the method of E-beam lithography. One 2.5-inch phase plate generated 9-view 3D images with horizontal-parallax, while the other 6-inch phase plate produced 64-view 3D images with full-parallax. The angular divergence in horizontal axis and vertical axis was 1.5 degrees, and 1.25 degrees, respectively, slightly larger than the simulated value of 1.2 degrees by Finite Difference Time Domain (FDTD). The intensity variation was less than 10% for each viewpoint, in consistency with the simulation results. On top of each phase plate, a high-resolution binary masking pattern containing amplitude information of all viewing zone was well aligned. We achieved a resolution of 400 pixels/inch and a viewing angle of 40 degrees for 9-view 3D images with horizontal parallax. In another prototype, the resolution of each view was 160 pixels/inch and the view angle was 50 degrees for 64-view 3D images with full parallax. As demonstrated in the experiments, the homemade lithography system provided the key fabricating technology for multiview 3D holographic display.

Multiview holographic 3D dynamic display by combining a nano-grating patterned phase plate and LCD

Limited by the refreshable data volume of commercial spatial light modulator (SLM), electronic holography can hardly provide satisfactory 3D live video. Here we propose a holography based multiview 3D display by separating the phase information of a lightfield from the amplitude information. In this paper, the phase information was recorded by a 5.5-inch 4-view phase plate with a full coverage of pixelated nano-grating arrays. Because only amplitude information need to be updated, the refreshing data volume in a 3D video display was significantly reduced. A 5.5 inch TFT-LCD with a pixel size of 95 μm was used to modulate the amplitude information of a lightfield at a rate of 20 frames per second. To avoid crosstalk between viewing points, the spatial frequency and orientation of each nano-grating in the phase plate was fine tuned. As a result, the transmission light converged to the viewing points. The angular divergence was measured to be 1.02 degrees (FWHM) by average, slightly larger than the diffraction limit of 0.94 degrees. By refreshing the LCD, a series of animated sequential 3D images were dynamically presented at 4 viewing points. The resolution of each view was 640 × 360. Images for each viewing point were well separated and no ghost images were observed. The resolution of the image and the refreshing rate in the 3D dynamic display can be easily improved by employing another SLM. The recoded 3D videos showed the great potential of the proposed holographic 3D display to be used in mobile electronics.

Tunable multi-wavelength polymer laser based on a triangular-lattice photonic crystal structure

A continuously tunable multi-wavelength polymer laser based on a triangular-lattice photonic crystal cavity is demonstrated. The triangular-lattice resonator was initially fabricated through multiple interference exposure and was then replicated into a low refractive index polymer via UV-nanoimprinting. The blend of a blue-emitting conjugated polymer and a red-emitting one was used as the gain medium. Three periods in the scalene triangular-lattice structure yield stable tri-wavelength laser emission (625.5 nm, 617.4 nm and 614.3 nm) in six different directions. A uniformly aligned liquid crystal (LC) layer was incorporated into the cavity as the top cladding layer. Upon heating, the orientation of LC molecules and thus the effective refractive index of the lasing mode changes which continuously shifts the lasing wavelength. A maximum tuning range of 12.2 nm was observed for the lasing mode at 625.5 nm. This tunable tri-wavelength polymer laser is simple constructed and cost-effective. It may find application in the fields of biosensors and photonic integrated circuits.

Surface profiling of an aspherical liquid lens with a varied thickness membrane

Inspired by crystalline lenses in human eyes, liquid lenses have a simple yet elegant working principle, and result in compact optical systems. Recent numerical studies showed that membranes with variable thicknesses could affect the lens profile. However, fabrication and assembly of a liquid lens with an inhomogeneous membrane is difficult. There is also a lack of experimental studies about the changes of a lens profile during deformation. In this paper, we provided a new experimental approach for characterizing the performance of a liquid lens with an inhomogeneous membrane. A 2D axisymmetric lens model was built in finite element analysis software to theoretically study the non-linear deformation behavior of the inhomogeneous membrane. Then we provided a new approach to fabricate inhomogeneous membranes using a pre-machined aluminum mold. An optical coherence tomography (OCT) system was used to dynamically measure the changes of a lens profile without contact. Both simulation and the experiments indicated that the variation of the thickness of the membrane could affect the lens profile in a predictable manner. A negative conic constant was achieved when a plano-concave membrane was adopted in a liquid lens. Larger increments of the thickness of the membrane in the radial direction resulted in a larger contribution of a conic constant to the lens profile. The presented study offers guidance for image-quality analysis and optimization of a liquid-lens-based optical system.

A multiview tabletop 3D display based on nano-gratings

Tabletop 3D display is a device that can provide several position-dependent 3D scenes in a circular viewing zone to viewers. In this paper, a kind of new method could provide a tabletop 3D display which was designed with the pixelated nano-gratings in pixels of the image and fabricated to modulate the collimated illumination light and project multiple converged transmitted light beams into each circular viewing zone. In this monochromatic tabletop display prototype, several viewing points were achieved in a circular viewing zone. The minimum angular separation set in this prototype between adjacent viewing points was 1 degree and the angular divergence of each viewing angle was measured and calculate as 0.958 degree. In this paper, the resolution of the generated 3D image at each view was 640×360 pixels. Using the proposed technology, the 360-degree viewable 3D display system can be constructed easily with multiple viewing points either evenly or unevenly distributed in the viewing zone. In addition, several artificially generated 3D image can be mixed well with the real physical objects placed on the tabletop screen, suggesting a natural mixed-reality environment provided by the proposed system. The potential applications of the proposed tabletop 3D display system are very comprehensive including desktop conference, tables games, trade show display, and sandtable.

Microfluidic channels incorporating organic distributed Bragg reflector lasers for in situ sensing applications

The in situ sensing capabilities of organic distributed Bragg reflector (DBR) laser sensors are demonstrated by exploiting the operation advantages of microfluidic channels. As an active cavity sensor that utilizes the narrow lasing peak as the detecting light, this novel in situ sensor features not only high sensitivity and high resolution, but also has advantages of low sample volume requirement, high temporal resolution and low cost. The device parameters are optimized using a multi-layer waveguiding model in terms of detection sensitivity and laser threshold. The economical, integrated and well-aligned organic DBR lasers by dot-matrix holography are incorporated into the microfluidic channels by using PVA as a bonding interlayer. Owing to the operation convenience, the detection capabilities are verified in terms of various physico-chemical processes including the refreshment of different fluids, the dynamical dissolution of glucose solution into variable concentrations and the real-time monitoring of the diffusion process. This work corroborates the in situ detection possibility of organic DBR lasers incorporating microfluidic channels as an active cavity sensor; and it simultaneously paves the way to disposable microfluidic lab-on-chips for various detection applications.