Wilhelm A. Groen
Delft University of Technology
Network
Latest external collaboration on country level. Dive into details by clicking on the dots.
Publication
Featured researches published by Wilhelm A. Groen.
Journal of Materials Chemistry | 2015
Tamara M. Eggenhuisen; Yulia Galagan; A. F. K. V. Biezemans; T. M. W. L. Slaats; W. P. Voorthuijzen; S. Kommeren; S. Shanmugam; J. P. Teunissen; A. Hadipour; W. J. H. Verhees; S. C. Veenstra; M. J. J. Coenen; J. Gilot; R. Andriessen; Wilhelm A. Groen
The organic photovoltaics field is maturing and reaching a technology readiness level where the focus is on developing large scale fabrication methods. In this light, fully inkjet printed organic solar cells were demonstrated. Inkjet printing allows direct patterning of all the layers, including the electrodes, offering full freedom of design without the use of masks or structuring by hardware. The semitransparent front and back electrodes consist of PEDOT:PSS and conductive Ag fingers, avoiding the use of ITO. The inkjet printing of six functional layer demonstrated minimal losses in performance as compared to the lab-scale standard, spin coated devices. All-inkjet printed large area (>1 cm2) organic solar cells with power conversion efficiency of 4.1% deposited from environmentally friendly solvents in an air atmosphere are demonstrated for the first time. Organic solar cells were fabricated using industrial scale (512 nozzles) printheads, compatible with R2R technology. To prove the great advantage of inkjet printing as a digital technology allowing freedom of forms and designs, large area organic solar cells with different artistic shapes were demonstrated. Reported results confirm that inkjet printing has high potential for the processing of OPV, allowing quick changes in design as well as the materials.
Review of Scientific Instruments | 2009
Daniel Irimia; Dimitar Dobrikov; Rob Kortekaas; Han Voet; Daan van den Ende; Wilhelm A. Groen; Maurice H. M. Janssen
In this paper we report on the design and operation of a novel piezovalve for the production of short pulsed atomic or molecular beams. The high speed valve operates on the principle of a cantilever piezo. The only moving part, besides the cantilever piezo itself, is a very small O-ring that forms the vacuum seal. The valve can operate continuous (dc) and in pulsed mode with the same drive electronics. Pulsed operation has been tested at repetition frequencies up to 5 kHz. The static deflection of the cantilever, as mounted in the valve body, was measured as a function of driving field strength with a confocal microscope. The deflection and high speed dynamical response of the cantilever can be easily changed and optimized for a particular nozzle diameter or repetition rate by a simple adjustment of the free cantilever length. Pulsed molecular beams with a full width at half maximum pulse width as low as 7 micros have been measured at a position 10 cm downstream of the nozzle exit. This represents a gas pulse with a length of only 10 mm making it well matched to for instance experiments using laser beams. Such a short pulse with 6 bar backing pressure behind a 150 microm nozzle releases about 10(16) particles/pulse and the beam brightness was estimated to be 4x10(22) particles/(s str). The short pulses of the cantilever piezovalve result in a much reduced gas load in the vacuum system. We demonstrate operation of the pulsed valve with skimmer in a single vacuum chamber pumped by a 520 l/s turbomolecular pump maintaining a pressure of 5x10(-6) Torr, which is an excellent vacuum to have the strong and cold skimmed molecular beam interact with laser beams only 10 cm downstream of the nozzle to do velocity map slice imaging with a microchannel-plate imaging detector in a single chamber. The piezovalve produces cold and narrow (Delta v/v=2%-3%) velocity distributions of molecules seeded in helium or neon at modest backing pressures of only 6 bar. The low gas load of the cantilever valve makes it possible to design very compact single chamber molecular beam machines with high quality cold and intense supersonic beams. The high speed cantilever piezovalve may find broad applicability in experiments where short and strong gas pulses are needed with only modest pumping, the effective use of (expensive) samples, or the production of cold atomic and molecular beams.
Applied Physics Letters | 2016
Dong Zhao; Ilias Katsouras; Kamal Asadi; Wilhelm A. Groen; Paul W. M. Blom; Dago M. de Leeuw
A homogeneous ferroelectric single crystal exhibits only two remanent polarization states that are stable over time, whereas intermediate, or unsaturated, polarization states are thermodynamically instable. Commonly used ferroelectric materials however, are inhomogeneous polycrystalline thin films or ceramics. To investigate the stability of intermediate polarization states, formed upon incomplete, or partial, switching, we have systematically studied their retention in capacitors comprising two classic ferroelectric materials, viz. random copolymer of vinylidene fluoride with trifluoroethylene, P(VDF-TrFE), and Pb(Zr,Ti)O3. Each experiment started from a discharged and electrically depolarized ferroelectric capacitor. Voltage pulses were applied to set the given polarization states. The retention was measured as a function of time at various temperatures. The intermediate polarization states are stable over time, up to the Curie temperature. We argue that the remarkable stability originates from the coexistence of effectively independent domains, with different values of polarization and coercive field. A domain growth model is derived quantitatively describing deterministic switching between the intermediate polarization states. We show that by using well-defined voltage pulses, the polarization can be set to any arbitrary value, allowing arithmetic programming. The feasibility of arithmetic programming along with the inherent stability of intermediate polarization states makes ferroelectric materials ideal candidates for multibit data storage.
Journal of Materials Chemistry | 2015
Yulia Galagan; Tamara M. Eggenhuisen; Mj Mart Coenen; Afkv Biezemans; Wjh Verhees; Sjoerd C. Veenstra; Wilhelm A. Groen; Ram Andriessen; Raj René Janssen
In this paper we discuss a problem-solving methodology and present guidance for troubleshooting defects in ITO-free all-solution processed organic solar cells with an inverted cell architecture. A systematic approach for identifying the main causes of failures in devices is presented. Comprehensive analysis of the identified failure mechanisms allowed us to propose practical solutions for further avoiding and eliminating failures in all-solution processed organic solar cells. Implementation of the proposed solutions has significantly improved the yield and quality of all-solution processed organic solar cells.
Journal of Intelligent Material Systems and Structures | 2013
Daan A. van den Ende; Wilhelm A. Groen; Sybrand van der Zwaag
High-strain environments, such as are found in automobile tires, provide deformation energy that can be harvested using piezoelectric materials, for instance, for powering electronics such as wireless sensors. Despite numerous efforts, none of the present devices easily satisfy the stringent operating and lifetime requirements for use inside a car tire, such as mechanical (accelerations of up to 3000 m/s2) and thermal requirements (temperatures of −40°C to 120°C), often leading to complex and costly solutions. Polymer–piezoelectric ceramic composite properties can be designed to fulfill the operating requirements. Furthermore, these materials are suitable for low-cost mass production and easy integration in the tire itself. Composite materials with increased output can be manufactured using the dielectrophoretic processing technique, which causes the alignment of the piezoelectric particles inside the polymer matrix, to obtain materials with adequate flexibility combined with a high energy density. In this study, we present the design, synthesis, and integration of novel composite material foils in automobile tires. The advantage of these dielectrophoretically structured composite materials is demonstrated and their output is compared to conventional piezoelectric composites. Furthermore, the charge signal output of a number of foil-based prototypes tested using an automobile tire test rig is evaluated and discussed with respect to energy harvesting performance.
IEEE Transactions on Components, Packaging and Manufacturing Technology | 2014
Daan van den Ende; Rob Hendriks; Romain Cauchois; Roel Kusters; Maarten Cauwe; Wilhelm A. Groen; Jeroen van den Brand
Ultrathin bare die chips and small-size surface mount device components were successfully soldered using a novel roll-to-roll compatible soldering technology. A high-power xenon light flash was used to successfully solder the components to copper tracks on polyimide (PI) and polyethylene terephthalate (PET) flex foils by using a lead-free solder paste. Results are compared with oven-reflowed solder joints on PI substrates. The delicate PET foil substrates were not damaged owing to the selectivity of light absorption, leading to a limited temperature increase in the PET foil while the chip and copper tracks were heated to a temperature high enough to initiate soldering. The microstructure of the soldered joints was investigated and found to be dependent on the photonic flash intensity. Reliability of the photonically soldered joints during damp heat testing and dynamic flexing testing was comparable with the reflowed benchmark and showed increased reliability compared with anisotropic conductive adhesives bonded on PET foils.
Applied Physics Letters | 2017
Thomas Lenz; Regina Hummel; Ilias Katsouras; Wilhelm A. Groen; Marlies Nijemeisland; Robert Ruemmler; Michael K. E. Schäfer; Dago M. de Leeuw
Recently reported piezoresponse force microscopy (PFM) measurements have proposed that porcine aortic walls are ferroelectric. This finding may have great implications for understanding biophysical properties of cardiovascular diseases such as arteriosclerosis. However, the complex anatomical structure of the aortic wall with different extracellular matrices appears unlikely to be ferroelectric. The reason is that a prerequisite for ferroelectricity, which is the spontaneous switching of the polarization, is a polar crystal structure of the material. Although the PFM measurements were performed locally, the phase-voltage hysteresis loops could be reproduced at different positions on the tissue, suggesting that the whole aorta is ferroelectric. To corroborate this hypothesis, we analyzed entire pieces of porcine aorta globally, both with electrical and electromechanical measurements. We show that there is no hysteresis in the electric displacement as well as in the longitudinal strain as a function of applied electric field and that the strain depends on the electric field squared. By using the experimentally determined quasi-static permittivity and Young’s modulus of the fixated aorta, we show that the strain can quantitatively be explained by Maxwell stress and electrostriction, meaning that the aortic wall is neither piezoelectric nor ferroelectric, but behaves as a regular dielectric material.
Applied Physics Letters | 2016
Thomas Lenz; Hamed Sharifi Dehsari; Kamal Asadi; Paul W. M. Blom; Wilhelm A. Groen; Dago M. de Leeuw
We demonstrate that ferroelectric memory diodes can be utilized as switching type positive temperature coefficient (PTC) thermistors. The diode consists of a phase separated blend of a ferroelectric and a semiconducting polymer stacked between two electrodes. The current through the semiconducting polymer depends on the ferroelectric polarization. At the Curie temperature the ferroelectric polymer depolarizes and consequently the current density through the semiconductor decreases by orders of magnitude. The diode therefore acts as switching type PTC thermistor. Unlike their inorganic counterparts, the PTC thermistors presented here are thin film devices. The switching temperature can be tuned by varying the Curie temperature of the ferroelectric polymer.
Ferroelectrics | 2016
Nijesh K. James; Tim P. Comyn; David A. Hall; Laurent Daniel; Annette P. Kleppe; Sybrand van der Zwaag; Wilhelm A. Groen
ABSTRACT The poling behaviour of tetragonal lead zirconate titanate (PZT) piezoelectric ceramic particles in a weakly conductive ionomer polymer matrix is investigated using high energy synchrotron X-ray diffraction analysis. The poling efficiency, crystallographic texture and lattice strain of the PZT particles inside the polymer matrix are determined and compared with the values for corresponding bulk ceramics reported in literature. The volume fraction of c-axis oriented domains and the lattice strain of the PZT particles are calculated from the changes in the integral intensities of the {200} peaks and the shift in the position of the {111} peaks respectively. It is shown that for an applied macroscopic field of 15 kV.mm−1, the PZT particles are effectively poled, leading to a maximum ν(002) domain reorientation volume fraction, of around 0.70. It is also found that a significant tensile lattice strain, ϵ{111}, of 0.6% occurs in the direction of the applied electric field, indicating the occurrence of residual stresses within the 2–4 μm size diameter particles. Although lower than that observed in poled tetragonal PZT ceramics, this level of lattice strain does indicate that the PZT particles within the composite experience significant elastic constraint. The correlation between the poling induced structural changes and the macroscopic piezoelectric and dielectric properties is discussed.
MRS Communications | 2012
Robert Abbel; Tim van Lammeren; Rob Hendriks; Jeroen Ploegmakers; Eric Rubingh; Erwin Rinaldo Meinders; Wilhelm A. Groen