William C. Chueh

High-flux solar-driven thermochemical dissociation of CO2 and H2O using nonstoichiometric ceria.

Fuel from Heat Plants grow by using energy from the Sun to convert carbon dioxide into sugar-based polymers and aromatics. These compounds in turn can be stripped of their oxygen, either through millennia of underground degradation to yield fossil fuels, or through a rather more rapid process of dissolution, fermentation, and hydrogenation to yield biofuels. Can we use sunlight to turn CO2 into hydrocarbon fuel without relying on the intervening steps of plant growth and breakdown? Chueh et al. (p. 1797) demonstrate one possible approach, in which concentrated sunlight heats cerium oxide to a sufficiently high temperature (∼1500°C) to liberate some oxygen from its lattice. The material then readily strips O atoms from either water or CO2, yielding hydrogen or CO, which can then be combined to form fuels. Solar heating of ceric oxide enables a cycle for conversion of carbon dioxide to carbon monoxide or water to hydrogen. Because solar energy is available in large excess relative to current rates of energy consumption, effective conversion of this renewable yet intermittent resource into a transportable and dispatchable chemical fuel may ensure the goal of a sustainable energy future. However, low conversion efficiencies, particularly with CO2 reduction, as well as utilization of precious materials have limited the practical generation of solar fuels. By using a solar cavity-receiver reactor, we combined the oxygen uptake and release capacity of cerium oxide and facile catalysis at elevated temperatures to thermochemically dissociate CO2 and H2O, yielding CO and H2, respectively. Stable and rapid generation of fuel was demonstrated over 500 cycles. Solar-to-fuel efficiencies of 0.7 to 0.8% were achieved and shown to be largely limited by the system scale and design rather than by chemistry.

A thermochemical study of ceria: exploiting an old material for new modes of energy conversion and CO2 mitigation.

We present a comprehensive thermodynamic and kinetic analysis of the suitability of cerium oxide (ceria) for thermochemical fuel production. Both portions of the two-step cycle, (i) oxygen release from the oxide at 1773 and 1873 K under inert atmosphere, and (ii) hydrogen release upon hydrolysis at 1073 K, are examined theoretically as well as experimentally. We observe gravimetric fuel productivity that is in quantitative agreement with equilibrium, thermogravimetric studies of ceria. Despite the non-stoichiometric nature of the redox cycle, in which only a portion of the cerium atoms change their oxidation state, the fuel productivity of 8.5–11.8 ml of H2 per gram of ceria is competitive with that of other solid-state thermochemical cycles currently under investigation. The fuel production rate, which is also highly attractive, at a rate of 4.6–6.2 ml of H2 per minute per gram of ceria, is found to be limited by a surface-reaction step rather than by ambipolar bulk diffusion of oxygen through the solid ceria. An evaluation of the thermodynamic efficiency of the ceria-based thermochemical cycle suggests that, even in the absence of heat recovery, solar-to-fuel conversion efficiencies of 16 to 19 per cent can be achieved, assuming a suitable method for obtaining an inert atmosphere for the oxygen release step.

High electrochemical activity of the oxide phase in model ceria–Pt and ceria–Ni composite anodes

Fuel cells, and in particular solid-oxide fuel cells (SOFCs), enable high-efficiency conversion of chemical fuels into useful electrical energy and, as such, are expected to play a major role in a sustainable-energy future. A key step in the fuel-cell energy-conversion process is the electro-oxidation of the fuel at the anode. There has been increasing evidence in recent years that the presence of CeO(2)-based oxides (ceria) in the anodes of SOFCs with oxygen-ion-conducting electrolytes significantly lowers the activation overpotential for hydrogen oxidation. Most of these studies, however, employ porous, composite electrode structures with ill-defined geometry and uncontrolled interfacial properties. Accordingly, the means by which electrocatalysis is enhanced has remained unclear. Here we demonstrate unambiguously, through the use of ceria-metal structures with well-defined geometries and interfaces, that the near-equilibrium H(2) oxidation reaction pathway is dominated by electrocatalysis at the oxide/gas interface with minimal contributions from the oxide/metal/gas triple-phase boundaries, even for structures with reaction-site densities approaching those of commercial SOFCs. This insight points towards ceria nanostructuring as a route to enhanced activity, rather than the traditional paradigm of metal-catalyst nanostructuring.

Ceria as a Thermochemical Reaction Medium for Selectively Generating Syngas or Methane from H2O and CO2

Doped CeO_2 with a low specific surface area is thermochemically cycled between MO_2 and MO_(2-δ) using H_2O and CO_2 as oxidants. The system rapidly and selectively produces syngas in the absence of a metal catalyst, and CH_4 in the presence of Ni. The Ni catalyst, which permits intermediate C to form on its surface, is proposed to shift the product from syngas to CH_4.

Intercalation Pathway in Many-Particle LiFePO4 Electrode Revealed by Nanoscale State-of-Charge Mapping

The intercalation pathway of lithium iron phosphate (LFP) in the positive electrode of a lithium-ion battery was probed at the ∼40 nm length scale using oxidation-state-sensitive X-ray microscopy. Combined with morphological observations of the same exact locations using transmission electron microscopy, we quantified the local state-of-charge of approximately 450 individual LFP particles over nearly the entire thickness of the porous electrode. With the electrode charged to 50% state-of-charge in 0.5 h, we observed that the overwhelming majority of particles were either almost completely delithiated or lithiated. Specifically, only ∼2% of individual particles were at an intermediate state-of-charge. From this small fraction of particles that were actively undergoing delithiation, we conclude that the time needed to charge a particle is ∼1/50 the time needed to charge the entire particle ensemble. Surprisingly, we observed a very weak correlation between the sequence of delithiation and the particle size, contrary to the common expectation that smaller particles delithiate before larger ones. Our quantitative results unambiguously confirm the mosaic (particle-by-particle) pathway of intercalation and suggest that the rate-limiting process of charging is initiating the phase transformation by, for example, a nucleation-like event. Therefore, strategies for further enhancing the performance of LFP electrodes should not focus on increasing the phase-boundary velocity but on the rate of phase-transformation initiation.

Sr- and Mn-doped LaAlO3−δ for solar thermochemical H2 and CO production

The increasing global appetite for energy within the transportation sector will inevitably result in the combustion of more fossil fuel. A renewable-derived approach to carbon-neutral synthetic fuels is therefore needed to offset the negative impacts of this trend, which include climate change. In this communication we report the use of nonstoichiometric perovskite oxides in two-step, solar-thermochemical water or carbon dioxide splitting cycles. We find that LaAlO3 doped with Mn and Sr will efficiently split both gases. Moreover the H2 yields are 9× greater, and the CO yields 6× greater, than those produced by the current state-of-the-art material, ceria, when reduced at 1350 °C and re-oxidized at 1000 °C. The temperature at which O2 begins to evolve from the perovskite is fully 300 °C below that of ceria. The materials are also very robust, maintaining their redox activity over at least 80 CO2 splitting cycles. This discovery has profound implications for the development of concentrated solar fuel technologies.

Current-induced transition from particle-by-particle to concurrent intercalation in phase-separating battery electrodes

Many battery electrodes contain ensembles of nanoparticles that phase-separate on (de)intercalation. In such electrodes, the fraction of actively intercalating particles directly impacts cycle life: a vanishing population concentrates the current in a small number of particles, leading to current hotspots. Reports of the active particle population in the phase-separating electrode lithium iron phosphate (LiFePO4; LFP) vary widely, ranging from near 0% (particle-by-particle) to 100% (concurrent intercalation). Using synchrotron-based X-ray microscopy, we probed the individual state-of-charge for over 3,000 LFP particles. We observed that the active population depends strongly on the cycling current, exhibiting particle-by-particle-like behaviour at low rates and increasingly concurrent behaviour at high rates, consistent with our phase-field porous electrode simulations. Contrary to intuition, the current density, or current per active internal surface area, is nearly invariant with the global electrode cycling rate. Rather, the electrode accommodates higher current by increasing the active particle population. This behaviour results from thermodynamic transformation barriers in LFP, and such a phenomenon probably extends to other phase-separating battery materials. We propose that modifying the transformation barrier and exchange current density can increase the active population and thus the current homogeneity. This could introduce new paradigms to enhance the cycle life of phase-separating battery electrodes.

Redox activity of surface oxygen anions in oxygen-deficient perovskite oxides during electrochemical reactions

Surface redox-active centres in transition-metal oxides play a key role in determining the efficacy of electrocatalysts. The extreme sensitivity of surface redox states to temperatures, to gas pressures and to electrochemical reaction conditions renders them difficult to investigate by conventional surface-science techniques. Here we report the direct observation of surface redox processes by surface-sensitive, operando X-ray absorption spectroscopy using thin-film iron and cobalt perovskite oxides as model electrodes for elevated-temperature oxygen incorporation and evolution reactions. In contrast to the conventional view that the transition metal cations are the dominant redox-active centres, we find that the oxygen anions near the surface are a significant redox partner to molecular oxygen due to the strong hybridization between oxygen 2p and transition metal 3d electronic states. We propose that a narrow electronic state of significant oxygen 2p character near the Fermi level exchanges electrons with the oxygen adsorbates. This result highlights the importance of surface anion-redox chemistry in oxygen-deficient transition-metal oxides.

Origin and hysteresis of lithium compositional spatiodynamics within battery primary particles

Watching batteries fail Rechargeable batteries lose capacity in part because of physical changes in the electrodes caused by electrochemical cycling. Lim et al. track the reaction dynamics of an electrode material, LiFePO4, by measuring the relative concentrations of Fe(II) and Fe(III) in it by means of high-resolution x-ray absorption spectrometry (see the Perspective by Schougaard). The exchange current density is then mapped for Li+ insertion and removal. At fast cycling rates, solid solutions form as Li+ is removed and inserted. However, at slow cycling rates, nanoscale phase separation occurs within battery particles, which eventually shortens battery life. Science, this issue p. 566; see also p. 543 X-ray microscopy shows the nanoscale evolution of the composition and reaction rate inside a Li-ion battery during cycling. The kinetics and uniformity of ion insertion reactions at the solid-liquid interface govern the rate capability and lifetime, respectively, of electrochemical devices such as Li-ion batteries. Using an operando x-ray microscopy platform that maps the dynamics of the Li composition and insertion rate in LixFePO4, we found that nanoscale spatial variations in rate and in composition control the lithiation pathway at the subparticle length scale. Specifically, spatial variations in the insertion rate constant lead to the formation of nonuniform domains, and the composition dependence of the rate constant amplifies nonuniformities during delithiation but suppresses them during lithiation, and moreover stabilizes the solid solution during lithiation. This coupling of lithium composition and surface reaction rates controls the kinetics and uniformity during electrochemical ion insertion.

Fast vacancy-mediated oxygen ion incorporation across the ceria–gas electrochemical interface

Electrochemical incorporation reactions are ubiquitous in energy storage and conversion devices based on mixed ionic and electronic conductors, such as lithium-ion batteries, solid-oxide fuel cells and water-splitting membranes. The two-way traffic of ions and electrons across the electrochemical interface, coupled with the bulk transport of mass and charge, has been challenging to understand. Here we report an investigation of the oxygen-ion incorporation pathway in CeO2-δ (ceria), one of the most recognized oxygen-deficient compounds, during hydrogen oxidation and water splitting. We probe the response of surface oxygen vacancies, electrons and adsorbates to the electrochemical polarization at the ceria-gas interface. We show that surface oxygen-ion transfer, mediated by oxygen vacancies, is fast. Furthermore, we infer that the electron transfer between cerium cations and hydroxyl ions is the rate-determining step. Our in operando observations reveal the precise roles of surface oxygen vacancy and electron defects in determining the rate of surface incorporation reactions.