Wolfgang Steinert

Effects of Reynolds Number and Free-Stream Turbulence on Boundary Layer Transition in a Compressor Cascade

An experimental and analytical study has been performed on the effect of Reynolds number and free-stream turbulence on boundary layer transition location on the suction surface of a controlled diffusion airfoil (CDA). The experiments were conducted in a rectilinear cascade facility at Reynolds numbers between 0.7 and 3.0 310 6 and turbulence intensities from about 0.7 to 4 percent. An oil streak technique and liquid crystal coatings were used to visualize the boundary layer state. For small turbulence levels and all Reynolds numbers tested, the accelerated front portion of the blade is laminar and transition occurs within a laminar separation bubble shortly after the maximum velocity near 35‐40 percent of chord. For high turbulence levels (Tu .3 percent) and high Reynolds numbers, the transition region moves upstream into the accelerated front portion of the CDA blade. For those conditions, the sensitivity to surface roughness increases considerably; at Tu54 percent, bypass transition is observed near 7 ‐10 percent of chord. Experimental results are compared to theoretical predictions using the transition model, which is implemented in the MISES code of Youngren and Drela. Overall, the results indicate that early bypass transition at high turbulence levels must alter the profile velocity distribution for compressor blades that are designed and optimized for high Reynolds numbers. @DOI: 10.1115/1.1413471#

3D Transonic Flow in a Compressor Cascade With Shock-Induced Corner Stall

An experimental and numerical study of the transonic flow through a linear compressor cascade with endwalls was conducted. The cascade with a low aspect ratio of 1.34 was tested at an inlet Mach number of 1.09 and a Reynolds number of 1.9×106. Detailed flow visualizations on the surfaces and 5-hole probe measurements inside the blading and in the wake region showed clearly a 3-dimensional boundary layer separation on the blade surface and the sidewall, and a severe corner stall induced by a strong 3D shock system at blade passage entrance.The experimental data has been used to validate and improve the 3D Navier-Stokes code TRACE. Results showed an excellent resolution of the complex flow field. Surface pressure distributions on the entire blade surface and the endwalls, flow angle and total pressure contours within the blade passage and the wake are compared with the experimental results. An analysis of the secondary flow of this highly staggered cascade did not show the classical corner vortex. Instead, a severe flow deviation and partly reverse flow near the walls is seen. The flow solver helped to identify a weak ring vortex that originates from the passage sidewall. Surface oil flow pictures on the blade contour and the sidewall are in qualitatively good agreement to numerical surface streaklines. A considerable improvement of the numerical results could be achieved by a gradual grid refinement especially in the corner region and by successive code development.Copyright

Advanced high-turning compressor airfoils for low Reynolds number condition: Part II: Experimental and numerical analysis

Part I of this paper describes the design and optimization of two high turning subsonic compressor cascades operating as an outlet guide vane (OGV) behind a single stage low pressure turbine at low Reynolds number condition (Re = 1.3 × 10 5 ). In the numerical optimization algorithm, the design point and off-design performance has been considered in an objective function to achieve a wide low loss incidence range. The objective of the present paper is to examine some of the characteristics describing the new airfoils as well as to prove the reliability of the design process and the applied flow salver Some aerodynamic characteristics for the two new airfoils and a conventional controlled diffusion airfoil (CDA), have been extensively investigated in the cascade wind tunnel of DLR Cologne. For an inlet Mach number of 0.6 the effect of Reynolds number and incidence angle on each airfoil performance is discussed, based on experimental and numerical results. For an interpretation of the airfoil boundary layer behavior, results of some boundary layer calculations are compared to oil flow visualization pictures. The design goal of an increased low loss incidence range at low Reynolds number condition could be confirmed without having a negative effect on the high Reynolds number region.

Advanced Nonaxisymmetric Endwall Contouring for Axial Compressors by Generating an Aerodynamic Separator—Part II: Experimental and Numerical Cascade Investigation

Modern methods for axial compressor design are capable of shaping the blade surfaces in a three-dimensional way. Linking these methods with automated optimization techniques provides a major benefit to the design process. The application of nonaxisymmetric contoured endwalls is considered to be very successful in turbine rotors and vanes. Concerning axial compressors, nonaxisymmetric endwalls are still a field of research. This two-part paper presents the recent development of a novel endwall design. A vortex created by a nonaxisymmetric endwall groove acts as an aerodynamic separator, preventing the passage vortex from interacting with the suction side boundary layer. This major impact on the secondary flow results in a significant loss reduction by means of load redistribution, reduction in recirculation areas, and suppressed corner separation. Part I of this paper deals with the endwall design and its compressor application. The resulting flow phenomena and physics are described and analyzed in detail. The second paper presents the detailed experimental and numerical investigation of the developed endwall groove. The measurements carried out at the transonic cascade wind tunnel of DLR in Cologne, demonstrated a considerable influence on the cascade performance. A loss reduction and redistribution of the cascade loading were achieved at the aerodynamic design point, as well as near the stall condition of the cascade. This behavior is well predicted by the numerical simulation. The combined analysis of experimental and numerical flow patterns allows a detailed interpretation and description of the resulting flow phenomena. In this context, high fidelity 3D-Reynolds-averaged Navier―Stokes flow simulations are required to analyze the complex blade and endwall boundary layer interaction.

3-D Transonic Flow in a Compressor Cascade With Shock-Induced Corner Stall

An experimental and numerical study of the transonic flow through a linear compressor cascade with endwalls was conducted. The cascade with a low aspect ratio of 1.34 was tested at an inlet Mach number of 1.09 and a Reynolds number of 1.9 310 6 . Detailed flow visualizations on the surfaces and five-hole probe measurements inside the blading and in the wake region showed clearly a three-dimensional boundary layer separation on the blade surface and the sidewall, and a severe corner stall induced by a strong 3-D shock system at blade passage entrance. The experimental data have been used to validate and improve the 3-D Navier-Stokes code TRACE. Results showed an excellent resolution of the complex flow field. Surface pressure distributions on the entire blade surface and the endwalls, flow angle and total pressure contours within the blade passage and the wake are compared with the experimental results. An analysis of the secondary flow of this highly staggered cascade did not show the classical corner vortex. Instead, a severe flow deviation and partly reverse flow near the walls is seen. The flow solver helped to identify a weak ring vortex that originates from the passage sidewall. Surface oil flow pictures on the blade contour and the sidewall are in qualitatively good agreement to numerical surface streaklines. A considerable improvement of the numerical results could be achieved by a gradual grid refinement, especially in the corner region and by successive code development.@DOI: 10.1115/1.1460913#

Design, Optimization, and Analysis of a High-Turning Transonic Tandem Compressor Cascade

As a feasibility study for a stator guide vane a highly loaded transonic compressor stator blade row was designed, optimized, and tested in a transonic cascade facility.The flow entering the turning device with an inlet Mach number of 1.06 has to be turned by more than 60° and diffused extremely to leave the blade row without swirl. Therefore, the basic question was: Is it feasible to gain such a high amount of flow turning with an acceptable level of total pressure losses?The geometric concept chosen is a tandem cascade consisting of a transonic blade row with a flow turning of 10° followed by a subsequent high-turning subsonic cascade. The blade number ratio of the two blade rows was selected to be 1:2 (transonic: subsonic).Design and optimization have been performed using a modern Navier-Stokes flow solver under 2D assumptions by neglecting side wall boundary-layer effects. In the design process it was found to be necessary to guide the wake of the low turning transonic blade near the suction surface of the subsonic blade. Furthermore, it is advantageous to enlarge the blade spacing of the ‘wake’ passage in relation to the neighbouring one of the high turning part.The optimized design geometry of the tandem cascade was tested in the transonic cascade windtunnel of the DLR in Cologne. At design flow conditions the experiments confirmed the design target in every aspect. A flow turning of more than 60°, a static pressure ratio of 1.75, and a total pressure loss coefficient of 0.15 was measured. The working range at design inlet Mach number of 1.06 is about 3.5° in terms of the inlet flow angle. A viscous analysis of various operating points showed excellent agreement with the experimental results.Copyright

Analyzing and optimizing geometrically degraded transonic fan blades by means of 2D and 3D simulations and cascade measurements

The present study deals with the influence of geometrically degraded transonic engine fan blades on the fan’s aerodynamic behavior. The study is composed of three phases; the first consists of 3D simulations to point out changes in the performance parameters caused by blade degradations. In the second phase, 2D optimizations are carried out to determine the potential of redesigning the blade and in the third phase, measurements on a transonic cascade are used to experimentally verify the numeric results.During engine operation as well as maintenance processes, geometric variations of the fan blades, and especially of the blades’ leading edges, are observed. They mainly originate from the ambient conditions under which the engine is operated. Though the deformations of the blade differ widely, several typical degradation types can be identified. In advance of the study, these degradation types have been systematized and simplified models representing different degrees of degradation have been built.In the first phase, the models are aerodynamically analyzed by means of 3D simulations. A high influence on the performance parameters is found for a fan blade exposed to long-term erosion. The model’s characteristics are a blunt leading edge and a reduced chord length. In contrast, the performance parameters of a model representing a re-contoured blade (reduced chord length but reshaped leading edge) are shown to be similar to those of a new fan blade. This leads to the conclusion that an eroded blade may offer almost the initial performance parameters as long as the leading edge is well reshaped.Since the model of the long-term eroded blade shows great changes in the fan’s performance and the best optimization potential, this has been chosen for the further analysis in the following phases.In the second phase, 2D optimizations are applied to three airfoil sections at different heights of the blade. The parameterization used is limited to a small area of the leading edge; the shape of the rest of the blade is kept constant. The optimizations lead to loss reduction and demonstrate the potential of the optimization process.The third phase is carried out in the Transonic Cascade Wind Tunnel of the Institute of Propulsion Technology in Cologne. As the transonic part of the fan blade is the most sensitive to geometric changes, a transonic airfoil with long-term erosion has been chosen. During the tests, the following measurement techniques are applied: Static pressure probes to determine the Mach number distribution, a 3-hole probe to detect exit angle and loss distribution, Schlieren photographs and PIV-measurements to locate the shock system, the L2F method to measure the cascade inflow angle and to resolve the boundary layer distribution and Liquid crystal measurements to observe transition activities. The full analysis of the measurements with PIV, L2F and Liquid Crystals are still in progress, but the evaluation of the loss polar and the Schlieren photographs show increased losses for the degraded blade and a good match with the numeric results.Copyright

Advanced High Turning Compressor Airfoils for Low Reynolds Number Condition: Part 2 — Experimental and Numerical Analysis

Part 1 of this paper describes the design and optimization of two high turning subsonic compressor cascades operating as an outlet guide vane (OGV) behind a single stage low pressure turbine at low Reynolds number condition (Re = 1.3×105 ). In the numerical optimization algorithm, the design point and off-design performance has been considered in an objective function to achieve a wide low loss incidence range. The objective of the present paper is to examine some of the characteristics describing the new airfoils as well as to prove the reliability of the design process and the applied flow solver. Some aerodynamic characteristics for the two new airfoils and a conventional controlled diffusion airfoil (CDA), have been extensively investigated in the cascade wind tunnel of DLR Cologne. For an inlet Mach number of 0.6 the effect of Reynolds number and incidence angle on each airfoil performance is discussed, based on experimental and numerical results. For an interpretation of the airfoil boundary layer behavior, results of some boundary layer calculations are compared to oil flow visualization pictures. The design goal of an increased low loss incidence range at low Reynolds number condition could be confirmed without having a negative effect on the high Reynolds number region.Copyright

Riblet Application in Compressors: Towards Efficient Blade Design?

Nowadays, modern axial compressors have already reached a very high level of development. The current study is focused on the question, if the application of riblets on the surfaces of a highly efficient modern compressor blade can be a further step towards more efficient blade design. Therefore, a highly loaded compressor cascade has been designed and optimized specifically for low Reynolds number conditions, as encountered at high altitudes and under consideration of the application of riblets. The optimization was performed at a Mach number of 0.6 and a Reynolds number of 1.5×105. Two objective functions were used. The aim of the first objective function was to minimize the cascade losses at the design point and at incidence angles of +5 and −5 degrees. The intention of the second objective function was to achieve a smooth distribution of the skin friction coefficient on the suction side of the blade by influencing the blade curvature in order to apply riblets. The MISES flow solver as well as the DLR optimizer “AutoOpti” were used for the optimization process.The developed compressor cascade was investigated in the transonic cascade wind tunnel of DLR in Cologne, where the Reynolds number was varied in the range of 1.5×105 to 9.0×105. Furthermore, the measurements were carried out at a low turbulence level of 0.8 percent and at a high turbulence level of 4 percent, representative for high pressure compressor stages. The measurement program was divided into two parts. The first part consisted of the investigation of the reference cascade. In the second part of the study riblets were applied on suction and pressure side of the cascade blades; two different manufacturing techniques, a rolling and a coating technique were applied. The rolling technique provides riblets with a width of 70 μm and the coated riblets have a width of 50 μm.The wake measurements were performed using a 3-hole probe at midspan of the cascade in order to determine the resulting losses of the reference blade and the blades with applied riblets. The detailed analysis of the measurements shows, that the riblets have only a slight influence on the viscous losses in the case of the compressor application in this study. Finally, these results are discussed and assessed against the background of feasibility and effort of riblet applications within the industrial design and manufacturing process.© 2014 ASME

Advanced Non-Axisymmetric Endwall Contouring for Axial Compressors by Generating an Aerodynamic Separator—Part II: Experimental and Numerical Cascade Investigation

Modern methods for axial compressor design are capable of shaping the blade surfaces in a three dimensional way. Linking these methods with automated optimization techniques provides a major benefit to the design process. The application of non-axisymmetric contoured endwalls is considered to be very successful in turbine rotors and vanes. Concerning axial compressors non-axisymmetric endwalls are still a field of research. This two-part paper presents the recent development of a novel endwall design. A vortex created by a nonaxisymmetric endwall groove acts as an aerodynamic separator, preventing the passage vortex from interacting with the suction side boundary layer. This major impact on the secondary flow results in a significant loss reduction by means of load redistribution, reduction of recirculation areas and suppressed corner separation. Part I of this paper deals with the endwall design and its compressor application. The resulting flow phenomena and physics are described and analysed in detail. The second paper presents the detailed experimental and numerical investigation of the developed endwall groove. The measurements carried out at the transonic cascade wind tunnel of DLR in Cologne, demonstrated a considerable influence on the cascade performance. A loss reduction and redistribution of the cascade loading were achieved at the aerodynamic design point as well as near the stall condition of the cascade. This behaviour is well predicted by the numerical simulation. The combined analysis of experimental and numerical flow patterns allows a detailed interpretation and description of the resulting flow phenomena. In this context high fidelity 3D-RANS flow simulations are required to analyse the complex blade and endwall boundary layer interaction.Copyright