Xavier Laloyaux

Temperature-Responsive Polymer Brushes Switching from Bactericidal to Cell-Repellent

Materials exhibiting antibacterial properties at room temperature and turning biocompatible and non-adhesive for in vivo conditions, are extremely attractive for devices that have to be ultimately introduced in living beings. Indeed, infections related to the use of invasive biomedical and medical items are still one of the main medical complications that cause high rates of mortality. [ 1 ] Despite sanitation protocols, a well-identifi ed route for patient bacterial infection is transmission through contaminated instruments such as intubation tubes, catheters, surgical drains or endoscopes that bypass the natural protective barriers of the body. [ 1 ]

Surface and Bulk Collapse Transitions of Thermoresponsive Polymer Brushes

We elucidate the sequence of events occurring during the collapse transition of thermoresponsive copolymer brushes based on poly(di(ethyleneglycol) methyl ether methacrylate) chains (PMEO2MA) grown by atom-transfer radical polymerization (ATRP). The collapse of the bulk of the brush is followed by quartz crystal microbalance measurements with dissipation monitoring (QCM-D), and the collapse of its outer surface is assessed by measuring equilibrium water contact angles in the captive bubble configuration. The bulk of the brush collapses over a broad temperature interval (approximately 25 degrees C), and the end of this process is signaled by a sharp first-order transition of the surface of the brush. These observations support theoretical predictions regarding the occurrence of a vertical phase separation during collapse, with surface properties of thermoresponsive brushes exhibiting a sharp variation at a temperature of T(br)(surf). In contrast, the bulk properties of the brush vary smoothly, with a bulk transition T(br)(bulk) occurring on average approximately 8 degrees C below T(br)(surf) and approximately 5 degrees C below the lower critical solution temperature (LCST) of free chains in solution. These observations should also be valid for planar brushes of other neutral, water-soluble thermoresponsive polymers such as poly(N-isopropylacrylamide) (PNIPAM). We also propose a way to analyze more quantitatively the temperature dependence of the QCM-D response of thermoresponsive brushes and deliver a simple thermodynamic interpretation of equilibrium contact angles, which can be of use for other complex temperature-responsive solvophilic systems.

Correlation between the Structure and Wettability of Photoswitchable Hydrophilic Azobenzene Monolayers on Silicon

Photoresponsive monolayers of hydrophilically substituted azobenzenes have been prepared by reaction on aminosilane monolayers on silicon surfaces. Grafting densities in the 0.2-1.0 molecule/nm(2) range were determined by X-ray reflectometry. The monolayers exhibit reversible photoisomerization, switching from a more hydrophilic trans state to a less hydrophilic cis state upon UV irradiation, in contrast with the usual behavior of most azobenzene monolayers that switch from a less to a more hydrophilic state. This indicates that the wettability is not dominated by the change in the dipole moment of the azobenzene moiety but originates from variations in the composition of the outer surface of the monolayers resulting from the reorientation of the substituent groups. The light-driven change in the water contact angle correlates linearly with the grafting density but remains small. However, the wettability contrast can be increased by forcing the molecules to stand in an improved vertical orientation, either by densifying the underlying aminosilane monolayer or by filling the voids left at the bottom of the layer of grafted azobenzene molecules.

Thicker is Better? Synthesis and Evaluation of Well-Defined Polymer Brushes with Controllable Catalytic Loadings

Polymer brushes (PBs) have been used as supports for the immobilization of palladium complexes on silicon surfaces. The polymers were grown by surface-initiated atom-transfer radical polymerization (SI-ATRP) and postdecorated with dipyridylamine (dpa) ligands. The pendant dpa units were in turn complexed with [Pd(OAc)(2)] to afford hybrid catalytic surfaces. A series of catalytic samples of various thicknesses (ca. 20-160 nm) and associated palladium loadings (ca. 10-45 nmol  cm(-2)) were obtained by adjusting the SI-ATRP reaction time and characterized by ellipsometry, X-ray reflectivity, X-ray photoelectron spectroscopy, and inductively coupled plasma mass spectrometry (ICP-MS). ICP-MS revealed a near-linear relationship between thickness of the polymer brush and palladium content, which confirmed the robustness of the preparation and postmodification sequence presented herein, rendering possible the creation of functional architectures with predefined catalytic potential. The activities of the catalytic PBs were determined by systematically exploring a full range of substrate-to-catalyst ratios in a model palladium(0)-catalyzed reaction. Quantitative transformations were observed for loadings down to 0.03 mol % and a maximum turnover number (TON) of around 3500 was established for the system. Comparison of the catalytic performances evidenced a singular influence of the thickness on conversions and TONs. The limited recyclability of the hairy catalysts has been attributed to palladium leaching.