Xuliang Lin

Reducing non-productive adsorption of cellulase and enhancing enzymatic hydrolysis of lignocelluloses by noncovalent modification of lignin with lignosulfonate

Four fractions of one commercial sodium lignosulfonate (SXP) with different molecular weight (MW) and anionic polymers were studied to reduce non-productive adsorption of cellulase on bound lignin in a lignocellulosic substrate. SXP with higher MW had stronger blocking effect on non-productive adsorption of a commercial Trichoderma reesi cellulase cocktail (CTec2) on lignin measured by quartz crystal microgravimetry with dissipation monitoring. Linear anionic aromatic polymers have strong blocking effect, but they would also reduce CTec2 adsorption on cellulose to decrease the enzymatic activity. The copolymer of lignin and polyethylene glycol (AL-PEG1000) has strong enhancement in enzymatic hydrolysis of lignocelluloses, because it not only improves the cellulase activity to cellulose, but also blocks the non-productive cellulase adsorption on lignin. Apart from improving the cellulase activity to cellulose, the enhancements of enzymatic hydrolysis of lignocellulose by adding AL-PEG1000 and SXPs are the result of the decreased cellulase non-productive adsorption on lignin.

Lignin-based polyoxyethylene ether enhanced enzymatic hydrolysis of lignocelluloses by dispersing cellulase aggregates.

Water-soluble lignin-based polyoxyethylene ether (EHL-PEG), prepared from enzymatic hydrolysis lignin (EHL) and polyethylene glycol (PEG1000), was used to improve enzymatic hydrolysis efficiency of corn stover. The glucose yield of corn stover at 72h was increased from 16.7% to 70.1% by EHL-PEG, while increase in yield with PEG4600 alone was 52.3%. With the increase of lignin content, EHL-PEG improved enzymatic hydrolysis of microcrystalline cellulose more obvious than PEG4600. EHL-PEG could reduce at least 88% of the adsorption of cellulase on the lignin film measured by quartz crystal microbalance with dissipation monitoring (QCM-D), while reduction with PEG4600 was 43%. Cellulase aggregated at 1220nm in acetate buffer analyzed by dynamic light scattering. EHL-PEG dispersed cellulase aggregates and formed smaller aggregates with cellulase, thereby, reduced significantly nonproductive adsorption of cellulase on lignin and enhanced enzymatic hydrolysis of lignocelluloses.

Effect of the molecular structure of lignin-based polyoxyethylene ether on enzymatic hydrolysis efficiency and kinetics of lignocelluloses

Effect of the molecular structure of lignin-based polyoxyethylene ether (EHL-PEG) on enzymatic hydrolysis of Avicel and corn stover was investigated. With the increase of PEG contents and molecular weight of EHL-PEG, glucose yield of corn stover increased. EHL-PEG enhanced enzymatic hydrolysis of corn stover significantly at buffer pH 4.8-5.5. Glucose yield of corn stover at 20% solid content increased from 32.8% to 63.8% by adding EHL-PEG, while that with PEG4600 was 54.2%. Effect of EHL-PEG on enzymatic hydrolysis kinetics of cellulose film was studied by quartz crystal microbalance with dissipation monitoring (QCM-D) and atomic force microscopy (AFM). An enhancing mechanism of EHL-PEG on enzymatic hydrolysis kinetics of cellulose was proposed. Cellulase aggregates dispersed by EHL-PEG excavated extensive cavities into the surface of cellulose film, making the film become more loose and exposed. After the maximum enzymatic hydrolysis rate, the film was mainly peeled off layer by layer until equilibrium.

Improving enzymatic hydrolysis of lignocellulosic substrates with pre-hydrolysates by adding cetyltrimethylammonium bromide to neutralize lignosulfonate.

Two pretreatment methods to overcome recalcitrance of lignocelluloses, sulfite pretreatment (SPORL) and dilute acid (DA), were conducted to pretreat softwood masson pine and hardwood eucalyptus for enzymatic hydrolysis. In the presence of corresponding pre-hydrolysates, adding moderate cetyltrimethylammonium bromide (CTAB) could enhance the enzymatic hydrolysis of the SPORL-pretreated substrates, but had no enhancement for the DA-pretreated substrates. The results showed that sodium lignosulfonate (SL) in pre-hydrolysates and CTAB together had a strong enhancement on the enzymatic hydrolysis of lignocelluloses. The compound of commercial lignosulfonate SXSL and CTAB (SXSL-CTAB) could enhance the substrate enzymatic digestibility (SED) of SPORL-pretreated masson pine from 27.1% to 71.0%, and that of DA-pretreated eucalyptus from 37.6% to 67.9%. The mechanism that CTAB increased the adsorption of SL on lignin to form more effective steric hindrance and reduced the non-productive adsorption of cellulase on lignin by neutralizing the negative charge of SL was proposed.

Using polyvinylpyrrolidone to enhance the enzymatic hydrolysis of lignocelluloses by reducing the cellulase non-productive adsorption on lignin

Polyvinylpyrrolidone (PVP) is an antifouling polymer to resist the adsorption of protein on solid surface. Effects of PVP on the enzymatic hydrolysis of pretreated lignocelluloses and its mechanism were studied. Adding 1g/L of PVP8000, the enzymatic digestibility of eucalyptus pretreated by dilute acid (Eu-DA) was increased from 28.9% to 73.4%, which is stronger than the classic additives, such as PEG, Tween and bovine serum albumin. Compared with PEG4600, the adsorption of PVP8000 on lignin was larger, and the adsorption layer was more stable and hydrophilic. Therefore, PVP8000 reduced 73.1% of the cellulase non-productive adsorption on lignin and enhanced the enzymatic hydrolysis of lignocelluloses greatly.

Fabrication and properties of low crystallinity nanofibrillar cellulose and a nanofibrillar cellulose–graphene oxide composite

Nanofibrillar cellulose with low crystallinity (LNC) was fabricated by adding water into a cellulose solution, which was facile, efficient and environmentally friendly. A strong and translucent nanofibrillar cellulose film with low crystallinity (LNCF) was prepared from a LNC suspension by filtration. Transmission electron microscopy showed that LNC was individually separated whiskers with a length of 200 nm, a width of 20 nm. Structure characterization of LNC showed that the main crystal form of LNC was cellulose II and the crystallinity was as low as 22.3%. LNCF exhibited excellent optical transparency of 91.7% when the thickness of the film was 40 μm. The tensile strength and youngs modulus of LNCF reached 64.7 MPa and 3062.8 MPa respectively. Meanwhile, a nanofibrillar cellulose–graphene oxide composite (LNC–GO) with a layer by layer structure was obtained by mixing LNC with graphene oxide at the mass ratio of 1 : 1, and the tensile strength and youngs modulus of LNC–GO were 84.3 MPa and 4406.2 MPa respectively.