Y. V. R. K. Prasad

Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242

A new method of modeling material behavior which accounts for the dynamic metallurgical processes occurring during hot deformation is presented. The approach in this method is to consider the workpiece as a dissipator of power in the total processing system and to evaluate the dissipated power co-contentJ = ∫oσ ε ⋅dσ from the constitutive equation relating the strain rate (ε) to the flow stress (σ). The optimum processing conditions of temperature and strain rate are those corresponding to the maximum or peak inJ. It is shown thatJ is related to the strain-rate sensitivity (m) of the material and reaches a maximum value(Jmax) whenm = 1. The efficiency of the power dissipation(J/Jmax) through metallurgical processes is shown to be an index of the dynamic behavior of the material and is useful in obtaining a unique combination of temperature and strain rate for processing and also in delineating the regions of internal fracture. In this method of modeling, noa priori knowledge or evaluation of the atomistic mechanisms is required, and the method is effective even when more than one dissipation process occurs, which is particularly advantageous in the hot processing of commercial alloys having complex microstructures. This method has been applied to modeling of the behavior of Ti-6242 during hot forging. The behavior of α+ β andβ preform microstructures has been exam-ined, and the results show that the optimum condition for hot forging of these preforms is obtained at 927 °C (1200 K) and a strain rate of 1CT•3 s•1. Variations in the efficiency of dissipation with temperature and strain rate are correlated with the dynamic microstructural changes occurring in the material.

Processing maps for hot working of titanium alloys

In recent years, processing maps are being used to design hot working schedules for making near-net shapes in a wide variety of materials. In this paper, the results obtained on the characterization of hot working behavior of titanium and its alloys using the approach of processing maps are described. In commercial purity α titanium, dynamic recrystallization (DRX) domain occurs at 775°C and 0.001 s−1 with an efficiency of power dissipation [2m/(m+1) where m is the strain rate sensitivity of flow stress] of 43%. The DRX domain shifts to higher strain rates when the interstitial impurity content is lowered. In the near-α and α-β alloys like IMI 685, Ti–6Al–4V, the preform microstructure has a significant influence on the processing maps. For example, in the transformed β (Widmanstatten) preform microstructures, these alloys exhibit a domain of spheroidization at lower temperature and a domain of β superplasticity at higher temperatures, both occurring at slow strain rates. These domains merge at the β transus because of the occurrence of damage processes which lower the tensile ductility. On the other hand, processing maps on alloys with equiaxed preform microstructure exhibit a clear superplasticity domain in the α-β range and the β phase undergoes DRX with a power dissipation efficiency of ≈45–55%. Titanium materials in general, exhibit wide flow instability regimes due to adiabatic shear bands formation at higher strain rates and hence careful process design has to be adopted for successful forging and microstructural control.

Characteristics of superplasticity domain in the processing map for hot working of as-cast Mg-11.5Li-1.5Al alloy

Processing map for hot working of as-cast Mg-11.5Li-1.5Al alloy has been developed in the temperature range 200 450degreesC and strain rate range 0.001-100 s(-1). The map exhibited a single domain with a peak efficiency of 65% occurring at 400degreesC and 0.001 s(-1). Under these conditions, the material exhibited abnormal elongation. On the basis of the elongation, the grain structure, the apparent activation energy for hot deformation (95 kJ mole (1)) and the peak efficiency of power dissipation (65% corresponding to a strain rate sensitivity of about 0.5), the domain is interpreted to represent superplasticity, At strain rates higher than about 10 s(-1), the material exhibits microstructural instability, while at temperatures of 450degreesC and it strain rate of 0.001 s (1), grain boundary cracking is observed.

Grain boundary strengthening in strongly textured magnesium produced by hot rolling

The grain size dependence of the yield stress in hot rolled 99.87 pct magnesium sheets and rods was measured in the temperature range 77 K to 420 K. Hot rolling produced strong basal textures and, for a given grain size, the hot rolled material has a higher strength than extruded material. The yield strength-grain size relation in the above temperature range follows the Hall-Petch equation, and the temperature dependencies of the Hall-Petch constants σ0 and k are in support of the theory of Armstrong for hcp metals that the intercept σ0 is related to the critical resolved shear stress (CRSS) for basal slip (easy slip) and the slope k is related to the CRSS for prismatic slip (difficult slip) occurring near the grain boundaries. In the hot rolled magnesium, σ0 is larger and k is smaller than in extruded material, observations which are shown to result from strong unfavorable basal and favorable {1010} textures, respectively. Texture affects the Hall-Petch constants through its effect on the orientation factors relating them to the CRSS for the individual slip systems controlling them.

Microstructural control in hot working of IN-718 superalloy using processing map

The hot-working characteristics of IN-718 are studied in the temperature range 900 °C to 1200 °C and strain rate range 0.001 to 100 s−1 using hot compression tests. Processing maps for hot working are developed on the basis of the strain-rate sensitivity variations with temperature and strain rate and interpreted using a dynamic materials model. The map exhibits two domains of dynamic recrystallization (DRX): one occurring at 950 °C and 0.001 s−1 with an efficiency of power dissipation of 37 pct and the other at 1200 °C and 0.1 s−1 with an efficiency of 40 pct. Dynamic recrystallization in the former domain is nucleated by the δ(Ni3Nb) precipitates and results in fine-grained microstructure. In the high-temperature DRX domain, carbides dissolve in the matrix and make interstitial carbon atoms available for increasing the rate of dislocation generation for DRX nucleation. It is recommended that IN-718 may be hot-forged initially at 1200 °C and 0.1 s−1 and finish-forged at 950 °C and 0.001 s−1 so that fine-grained structure may be achieved. The available forging practice validates these results from processing maps. At temperatures lower than 1000 °C and strain rates higher than 1 s−1 the material exhibits adiabatic shear bands. Also, at temperatures higher than 1150°C and strain rates more than 1s−1, IN-718 exhibits intercrystalline cracking. Both these regimes may be avoided in hotworking IN-718.

Dynamic recrystallization during hot deformation of aluminum : a study using processing maps

The hot deformation behavior of aluminum of different purities has been studied in the temperature range of 250 °C to 600 °C and strain-rate range of 10 3 to 102 s’1. On the basis of the flow stress data, the strain-rate sensitivity (m) of the material is evaluated and used for establishing power dissipation maps following the Dynamic Materials Model. These maps depict the variation of the efficiency of power dissipation [η = 2m/(m +1)] with temperature and strain rate. A domain of dynamic recrystallization (DRX) could be identified in these maps. While the strain rate at which the efficiency peak occurred in this domain is 10-3 s−1 the DRX temperature is purity dependent and is 375 °C for 99.999 pct Al, 450 °C for 99.995 pct Al, 550 °C for 99.94 pct Al, and 600 °C for 99.5 pct Al. The maximum efficiency of power dissipation for DRX in aluminum is about 55 pct. The sigmoidal increase of grain size with temperature in the DRX domain and the decrease in the DRX temperature with increase in the purity of aluminum are very similar to that observed in static recrystallization, although DRX occurred at much higher temperatures.

Processing map for hot working of alpha-zirconium

The hot deformation characteristics of alpha-zirconium in the temperature range of 650 °C to 850 °C and in the strain-rate range of 10-3 to 102 s-1 are studied with the help of a power dissipation map developed on the basis of the Dynamic Materials Model.[7,8,9] The processing map describes the variation of the efficiency of power dissipation (η =2m/m + 1) calculated on the basis of the strain-rate sensitivity parameter (m), which partitions power dissipation between thermal and microstructural means. The processing map reveals a domain of dynamic recrystallization in the range of 730 °C to 850 °C and 10−2 to 1−1 with its peak efficiency of 40 pct at 800 °C and 0.1 s-1 which may be considered as optimum hot-working parameters. The characteristics of dynamic recrystallization are similar to those of static recrystallization regarding the sigmoidal variation of grain size (or hardness) with temperature, although the dynamic recrystallization temperature is much higher. When deformed at 650 °C and 10-3 s-1 texture-induced dynamic recovery occurred, while at strain rates higher than 1 s-1, alpha-zirconium exhibits microstructural instabilities in the form of localized shear bands which are to be avoided in processing.

Processing map for the hot working of near-α titanium alloy 685

Using a dynamic materials model, processing and instability maps have been developed for near-alpha titanium alloy 685 in the temperature range 775-1025 degrees C and strain-rate range of 0.001-10 s(-1) to optimise its hot workability. The alloys beta-transus temperature lies at about 1020 degrees C. The material undergoes superplasticity with a peak efficiency of 80% at 975 degrees C and 0.001 s(-1), which are the optimum parameters for alpha-beta working. The occurrence of superplasticity is attributed to two-phase microduplex structure, higher strain-rate sensitivity, low flow stress and sigmoidal variation between log flow stress and log strain rate. The material also exhibits how localisation due to adiabatic shear-band formation up to its beta-transus temperature with strain rates greater than 0.02 s(-1) and thus cracking along these regions

Processing of iron aluminides

A processing route comprising of air induction melting (AIM) with protective cover and electroslag remelting (ESR) for production of iron aluminide

Characterization of hot deformation behaviour of Zr---2.5Nb---0.5Cu using processing maps

(Fe_3Al)