Yen-Sook Jung

Toward Large Scale Roll‐to‐Roll Production of Fully Printed Perovskite Solar Cells

Fully printed perovskite solar cells are demonstrated with slot-die coating, a scalable printing method. A sequential slot-die coating process is developed to produce efficient perovskite solar cells and to be used in a large-scale roll-to-roll printing process. All layers excluding the electrodes are printed and devices demonstrate up to 11.96% power conversion efficiency. It is also demonstrated that the new process can be used in roll-to-roll production.

Sulfonic acid-functionalized, reduced graphene oxide as an advanced interfacial material leading to donor polymer-independent high-performance polymer solar cells

A r-GO with sulfonic acid groups (sr-GO) was newly developed and it showed dramatically concentrated aqueous dispersions with high film conductivity. With the aid of sulfonic acid groups, good compatibility with various HOMO materials was achieved, resulting in PCEs over 7% for sr-GO-based cells with superior device stability to PEDOT:PSS-based devices.

Differentially pumped spray deposition as a rapid screening tool for organic and perovskite solar cells

We report a spray deposition technique as a screening tool for solution processed solar cells. A dual-feed spray nozzle is introduced to deposit donor and acceptor materials separately and to form blended films on substrates in situ. Using a differential pump system with a motorised spray nozzle, the effect of film thickness, solution flow rates and the blend ratio of donor and acceptor materials on device performance can be found in a single experiment. Using this method, polymer solar cells based on poly(3-hexylthiophene) (P3HT):(6,6)-phenyl C61 butyric acid methyl ester (PC61BM) are fabricated with numerous combinations of thicknesses and blend ratios. Results obtained from this technique show that the optimum ratio of materials is consistent with previously reported values confirming this technique is a very useful and effective screening method. This high throughput screening method is also used in a single-feed configuration. In the single-feed mode, methylammonium iodide solution is deposited on lead iodide films to create a photoactive layer of perovskite solar cells. Devices featuring a perovskite layer fabricated by this spray process demonstrated a power conversion efficiencies of up to 7.9%.

One-Step Printable Perovskite Films Fabricated under Ambient Conditions for Efficient and Reproducible Solar Cells

Despite the potential of roll-to-roll processing for the fabrication of perovskite films, the realization of highly efficient and reproducible perovskite solar cells (PeSCs) through continuous coating techniques and low-temperature processing is still challenging. Here, we demonstrate that efficient and reliable CH3NH3PbI3 (MAPbI3) films fabricated by a printing process can be achieved through synergetic effects of binary processing additives, N-cyclohexyl-2-pyrrolidone (CHP) and dimethyl sulfoxide (DMSO). Notably, these perovskite films are deposited from premixed perovskite solutions for facile one-step processing under a room-temperature and ambient atmosphere. The CHP molecules result in the uniform and homogeneous perovskite films even in the one-step slot-die system, which originate from the high boiling point and low vapor pressure of CHP. Meanwhile, the DMSO molecules facilitate the growth of perovskite grains by forming intermediate states with the perovskite precursor molecules. Consequently, fully printed PeSC based on the binary additive system exhibits a high PCE of 12.56% with a high reproducibility.

Domain-engineered BiFeO3 thin-film photoanodes for highly enhanced ferroelectric solar water splitting

In photoelectrochemical (PEC) water splitting, charge separation and collection by the electric field in the photoactive material are the most important factors for improved conversion efficiency. Hence, ferroelectric oxides, in which electrons are the majority carriers, are considered promising photoanode materials because their high built-in potential, provided by their spontaneous polarization, can significantly enhance the separation and drift of photogenerated carriers. In this regard, the PEC properties of BiFeO3 thin-film photoanodes with different crystallographic orientations and consequent ferroelectric domain structures are investigated. As the crystallographic orientation changes from (001)pc via (110)pc to (111)pc, the ferroelastic domains in epitaxial BiFeO3 thin films become mono-variant and the spontaneous polarization levels increase to 110 μC/cm2. Consequently, the photocurrent density at 0 V vs. Ag/AgCl increases approximately 5.3-fold and the onset potential decreases by 0.180 V in the downward polarization state. It is further demonstrated that ferroelectric switching in the (111)pc BiFeO3 thin-film photoanode leads to an approximate change of 8,000% in the photocurrent density and a 0.330 V shift in the onset potential. This study strongly suggests that domain-engineered ferroelectric materials can be used as effective charge separation and collection layers for efficient solar water-splitting photoanodes.

Slot-Die Coated Perovskite Films Using Mixed Lead Precursors for Highly Reproducible and Large-Area Solar Cells

Recently, many kinds of printing processes have been studied to fabricate perovskite solar cells (PeSCs) for mass production. Among them, slot-die coating is a promising candidate for roll-to-roll processing because of high-throughput, easy module patterning, and a premetered coating system. In this work, we employed mixed lead precursors consisting of PbAc2 and PbCl2 to fabricate PeSCs via slot-die coating. We observed that slot-die-coated perovskite films based on the mixed lead precursors exhibited well-grown and uniform morphology, which was hard to achieve by using only a single lead source. Consequently, PeSCs made with this precursor system showed improved device performance and reproducibility over single PbAc2. Lastly, a large-area module with an active area of 10 cm2 was fabricated with a power conversion efficiency of 8.3%.

Sequent spray deposition of secondary solvent for efficient polymer solar cells

The spray process is compatible with the roll-to-roll process, which has the highest productivity and the lowest costs among the developed processing techniques. In this study, we demonstrated a technique involving the spraying of a secondary solvent after the formation of an active layer, by using a spray process with a relatively lowboiling- point solution. With this technique, we obtained the much smoother surface topography and more ordered bulk heterojunction morphology through enhanced self-organization of the composite materials. Consequently, the device with additionally sprayed high-boiling-point solvent allowed to achieve fill factor (FF) and power conversion efficiency (PCE) values as high as 67% and 3.76%, respectively.

Enhanced optical output of InGaN/GaN near-ultraviolet light-emitting diodes by localized surface plasmon of colloidal silver nanoparticles

We report on the characteristics of localized surface plasmon (LSP)-enhanced near-ultraviolet light-emitting diodes (NUV-LEDs) fabricated by using colloidal silver (Ag) nanoparticles (NPs). Colloidal Ag NPs were deposited on the 20 nm thick p-GaN spacer layer using a spray process. The optical output power of NUV-LEDs with colloidal Ag NPs was increased by 48.7% at 20 mA compared with NUV-LEDs without colloidal Ag NPs. The enhancement was attributed to increased internal quantum efficiency caused by the resonance coupling between excitons in the multiple quantum wells and the LSPs in the Ag NPs.

Small-Molecule Organic Photovoltaic Modules Fabricated via Halogen-Free Solvent System with Roll-to-Roll Compatible Scalable Printing Method

For the first time, the photovoltaic modules composed of small molecule were successfully fabricated by using roll-to-roll compatible printing techniques. In this study, blend films of small molecules, BTR and PC71BM were slot-die coated using a halogen-free solvent system. As a result, high efficiencies of 7.46% and 6.56% were achieved from time-consuming solvent vapor annealing (SVA) treatment and roll-to-roll compatible solvent additive approaches, respectively. After successful verification of our roll-to-roll compatible method on small-area devices, we further fabricated large-area photovoltaic modules with a total active area of 10 cm2, achieving a power conversion efficiency (PCE) of 4.83%. This demonstration of large-area photovoltaic modules through roll-to-roll compatible printing methods, even based on a halogen-free solvent, suggests the great potential for the industrial-scale production of organic solar cells (OSCs).