Yeojoon Yoon

Bromate removal from water by granular ferric hydroxide (GFH)

The feasibility of granular ferric hydroxide (GFH) for bromate removal from water has been studied. Batch experiments were performed to study the influence of various experimental parameters such as effect of contact time, initial bromate concentration, temperature, pH and effect of competing anions on bromate removal by GFH. The adsorption kinetics indicates that uptake rate of bromate was rapid at the beginning and 75% adsorption was completed in 5 min and equilibrium was achieved within 20 min. The sorption process was well described by pseudo-second-order kinetics. The maximum adsorption potential of GFH for bromate removal was 16.5 mg g(-1) at 25 degrees C. The adsorption data fitted well to the Langmuir model. The increase in OH peak and absence of Br-O bonding in FTIR spectra indicate that ion-exchange was the main mechanism during bromate sorption on GFH. The effects of competing anions and solution pHs (3-9) were negligible. Results of the present study suggest that GFH can be effectively utilized for bromate removal from drinking water.

Removal of amoxicillin by UV and UV/H2O2 processes

The degradation of the β-lactam antibiotic amoxicillin (AM) treated with direct UV-C and UV/H(2)O(2) photolytic processes was investigated in the present study. In addition, the antibacterial activity of the solution treated by UV/H(2)O(2) advanced oxidation was compared with AM solution treated with ozone. The degradation rate of amoxicillin in both processes fitted pseudo first-order kinetics, and the rates increased up to six fold with increasing H(2)O(2) addition at 10mM H(2)O(2) compared to direct photolysis. However, low mineralization was achieved in both processes, showing a maximum of 50% TOC removal with UV/H(2)O(2) after a reaction time of 80min (UV dose: 3.8×10(-3)EinsteinL(-1)) with the addition of 10mM H(2)O(2). The transformation products formed during the degradation of amoxicillin in the UV and UV/H(2)O(2) processes were identified by LC-IT-TOF analysis. In addition, microbial growth inhibition bioassays were performed to determine any residual antibacterial activity from potential photoproducts remaining in the treated solutions. An increase of the antibacterial activity in the UV/H(2)O(2) treated samples was observed compared to the untreated sample in a time-based comparison. However, the UV/H(2)O(2) process effectively eliminated any antibacterial activity from AM and its intermediate photoproducts at 20min of contact time with a 10mM H(2)O(2) dose after the complete elimination of AM, even though the UV/H(2)O(2) advanced oxidation process led to bioactive photoproducts.

Comparative evaluation of magnetite-graphene oxide and magnetite-reduced graphene oxide composite for As(III) and As(V) removal.

Arsenic removal using Fe3O4-graphene oxide composite (M-GO) and Fe3O4-reduced graphene oxide composite (M-rGO) was investigated. The M-GO was more effective to adsorb both As(III) and As(V) than M-rGO, because the more functional groups existing on the M-GO could lead to synthesize more Fe3O4 with M-GO. As(III) was more favorable to be adsorbed than As(V) onto both M-GO and M-rGO. According to the effect of pH on arsenic removal, the electrostatic interaction between the positively charged surface of Fe3O4-graphene based adsorbents and anionic As(V) species was a major factor to adsorb As(V). The adsorption mechanism of As(III), on the other hand, was strongly affected by a surface complexation, rather than electrostatic interactions. Consequently, in terms of the process energy consumption, energy saving could be achieved via omitting the reduction process to fabricate M-rGO from M-GO and the pre-oxidation process to convert As(III) to As(V).

Evidence of singlet oxygen and hydroxyl radical formation in aqueous goethite suspension using spin-trapping electron paramagnetic resonance (EPR).

The generation of reactive species in an aqueous goethite suspension, under room light and aeration conditions, was investigated using the electron paramagnetic resonance (EPR) technique employing spin trap agents. The trap reagents, including 5,5-dimethylpyrroline N-oxide (DMPO) and 2,2,6,6-tetramethylpiperidine (TEMP), were used for the detection of OH radicals (OH·) and singlet oxygen (1O2), respectively. On the addition of DMPO to the goethite suspended solution, a DMPO-OH adduct was formed, which was not decreased, even in the presence of the OH· scavenger, mannitol. This result implied a false positive interpretation from the DMPO-OH EPR signal. In the presence of TEMP reagent, a TEMP-O signal was detected, which was completely inhibited in the presence of the singlet oxygen scavenger, sodium azide. With both DMPO-OH and TEMP-O radicals in the presence and absence of radical scavengers, singlet oxygen was observed to be the key species formed in the room-light sensitized goethite suspension. In the goethite/H2O2 system; however, both OH· and singlet oxygen were generated, with significant portions of DMPO-OH resulting from both OH· and singlet oxygen. In fact, the DMPO-OH resulting from OH· should be carefully calculated by correcting for the amount of DMPO-OH due to singlet oxygen. This study reports, for the first time, that the goethite suspensions may also act as a natural sensitizer, such as fulvic acids, to form singlet oxygen.

Characterization of films and interfaces in n-ZnO/p-Si photodiodes

We report on the fabrication of n-ZnO/p-Si heterojunction photodiodes. RF sputtering was performed to deposit ZnO films on p-Si substrates at various substrate temperatures of 300, 480 and 550 °C using Ar:O2 ratios of 6:1. Typical rectifying behaviors were observed from most of the diodes as characterized by the current–voltage (I–V) measurement. Some of the diodes exhibit photoelectric effects under illumination using monochromatic red light with a wavelength of 670 nm. Maximum quantum efficiency of 53% was obtained under a reverse bias condition from a diode with ZnO film deposited at 480 °C. Measuring photoluminescence, transmittance, sheet resistance from the ZnO films, and characterizing the n-ZnO/p-Si interface with X-ray photoelectron spectroscopy, it is concluded that the diodes with n-ZnO deposited at 480 °C conserve relatively a high film quality and good interface junction to exhibit the best photoelectric property.

Removal of iopromide and degradation characteristics in electron beam irradiation process

The aim of this study is to evaluate the removal efficiency of iopromide using electron beam (E-beam) irradiation technology, and its degradation characteristics with hydroxyl radical (OH) and hydrated electron (e(aq)(-)). Studies are conducted with different initial concentrations of iopromide in pure water and in the presence of hydrogen peroxide, bicarbonate ion, or sulfite ion. E-beam absorbed dose of 19.6 kGy was required to achieve 90% degradation of 100 μM iopromide and the E-beam/H(2)O(2) system increased the removal efficiency by an amount of OH· generation. In the presence of OH scavengers (10 mM sulfite ion), the required dose for 90% removal of 100 μM iopromide was only 0.9 kGy. This greatly enhanced removal was achieved in the presence of OH· scavengers, which was rather unexpected and unlike the results obtained from most advanced oxidation process (AOP) experiments. The reasons for this enhancement can be explained by a kinetic study using the bimolecular rate constants of each reaction species. To explore the reaction scheme of iopromide with OH· or e(aq)(-) and the percent of mineralization for the two reaction paths, the total organic carbon (TOC), released iodide, and intermediates were analyzed.

Inactivation characteristics of ozone and electrolysis process for ballast water treatment using B. subtilis spores as a probe

Since ballast water affects the ocean ecosystem, the International Maritime Organization (IMO) sets a standard for ballast water management and might impose much tighter regulations in the future. The aim of this study is to evaluate the inactivation efficiency of ozonation, electrolysis, and an ozonation-electrolysis combined process, using B. subtilis spores. In seawater ozonation, HOBr is the key active substance for inactivation, because of rapid reactivity of ozone with Br(-) in seawater. In seawater electrolysis, it is also HOBr, but not HOCl, because of the rapid reaction of HOCl with Br(-), which has not been recognized carefully, even though many electrolysis technologies have been approved by the IMO. Inactivation pattern was different in ozonation and electrolysis, which has some limitations with the tailing or lag-phase, respectively. However, each deficiency can be overcome with a combined process, which is most effective as a sequential application of ozonation followed by electrolysis.

pH Effect on Ozonation of Ampicillin: Kinetic Study and Toxicity Assessment

Ampicillin (AP) is a penicillin-type antibiotic and one of the most widely used bacteriostatic antibiotics in human and veterinary medicine. A kinetic study was performed under different pH conditions (5, 7.2, and 9) to determine the degradation efficiency of AP by ozonation. The second-order rate constants for the direct reaction of AP with ozone were measured to be 2.2 ˜5.4×105 M−1s−1 under the pH conditions tested. The rate constants were greater at higher pH. The potential toxicity of the AP intermediates formed after ozonation under the various pH conditions were examined using a bioluminescence assay on Vibrio fischeri species. The biodegradability of the AP degraded products was also determined by measuring the BOD5/COD of the ozonated samples under the different pH conditions. A lower biodegradability and acute toxicity was observed at the lowest pH (pH 5). These results suggest that higher pH conditions are needed for the removal of AP by ozonation in order to mitigate the residual toxicity that can remain even after complete removal of the parent compound by ozonation.

Evaluation of disinfection efficacy and chemical formation using MPUV ballast water treatment system (GloEn-PatrolTM)

This study was undertaken to evaluate the efficacy of inactivation of several indigenous marine species and the formation of oxidants and other by-products using medium-pressure ultraviolet (MPUV) ballast water treatment. The ballast water treatment system (BWTS) used in this study was composed of filtration modules as a pretreatment process, followed by a UV irradiation process equipped with a polychromatic MPUV lamp. The experiments were performed on seawater (Busan,>32 PSU) and brackish water (Nakdong River, 20–22 PSU) with flow rates of 50 and 250 m3/h. The disinfection efficacy of the system was evaluated using indigenous species (>50 μ m and 10–50 μ m) and surrogate microorganisms (E. coli and Enterococci group). The test results successfully met the D-2 regulation of the IMO (International Marine Organization). In addition, oxidants, such as H2O2, total residual oxidants (TRO) and OH radicals, and potential halogenated by-products, such as haloacetic acids, trihalomethanes and total organic halides, that had potentially formed after MPUV treatment, were measured. In conclusion, the ballast water treatment system employing the MPUV physical process not only effectively eliminated indigenous species in ballast water but also generated no harmful by-products.

Evaluation of the formation of oxidants and by-products using Pt/Ti, RuO2/Ti, and IrO2/Ti electrodes in the electrochemical process.

The aim of this study was to evaluate the formation of oxidants and by-products by using different electrode materials, such as Pt/Ti, RuO2/Ti, and IrO2/Ti, in the electrochemical process. The harmful by-products and were formed during the electrolysis of a Cl− electrolyte solution, as well as active chlorine, which is the most common water disinfectant. With regard to drinking water treatment, the most efficient electrode was defined as that leading to a higher formation of active chlorine and a lower formation of hazardous by-products. Overall, it was found that the Pt/Ti electrode should not be used for drinking water treatment applications, while the IrO2/Ti and RuO2/Ti electrodes are ideal for use.