Yiju Li

Flexible, solid-state, ion-conducting membrane with 3D garnet nanofiber networks for lithium batteries

Significance This work describes a flexible, solid-state, lithium-ion–conducting membrane based on a 3D ion-conducting network and polymer electrolyte for lithium batteries. The 3D ion-conducting network is based on percolative garnet-type Li6.4La3Zr2Al0.2O12 solid-state electrolyte nanofibers, which enhance the ionic conductivity of the solid-state electrolyte membrane at room temperature and improve the mechanical strength of the polymer electrolyte. The membrane has shown superior electrochemical stability to high voltage and high mechanical stability to effectively block lithium dendrites. This work represents a significant breakthrough to enable high performance of lithium batteries. Beyond state-of-the-art lithium-ion battery (LIB) technology with metallic lithium anodes to replace conventional ion intercalation anode materials is highly desirable because of lithium’s highest specific capacity (3,860 mA/g) and lowest negative electrochemical potential (∼3.040 V vs. the standard hydrogen electrode). In this work, we report for the first time, to our knowledge, a 3D lithium-ion–conducting ceramic network based on garnet-type Li6.4La3Zr2Al0.2O12 (LLZO) lithium-ion conductor to provide continuous Li+ transfer channels in a polyethylene oxide (PEO)-based composite. This composite structure further provides structural reinforcement to enhance the mechanical properties of the polymer matrix. The flexible solid-state electrolyte composite membrane exhibited an ionic conductivity of 2.5 × 10−4 S/cm at room temperature. The membrane can effectively block dendrites in a symmetric Li | electrolyte | Li cell during repeated lithium stripping/plating at room temperature, with a current density of 0.2 mA/cm2 for around 500 h and a current density of 0.5 mA/cm2 for over 300 h. These results provide an all solid ion-conducting membrane that can be applied to flexible LIBs and other electrochemical energy storage systems, such as lithium–sulfur batteries.

All-wood, low tortuosity, aqueous, biodegradable supercapacitors with ultra-high capacitance

In energy storage devices, the critical demands for high energy/power density, low cost, long cycle lives and environmental friendliness have highlighted an urgent need for developing storage electrodes with low cost, large thickness, high mass loading, low tortuosity and high energy/power density. Here we demonstrate the design and construction of an all-wood-structured asymmetric supercapacitor (ASC) based on an activated wood carbon (AWC) anode, a wood membrane separator and a MnO2/wood carbon (MnO2@WC) cathode. The structural virtues of the all-wood-structured ASC device – desirable thickness (up to ∼1 mm), direct channels with low tortuosity, high electronic and ionic conductivity – enable ASC high areal mass loadings (up to 30 mg cm−2 for the anode and 75 mg cm−2 for the wood carbon/MnO2 composite cathode), a high energy density of 1.6 mW h cm−2 and a maximum power density of 24 W cm−2, representing the highest mass loading and areal energy/power densities among all reported MnO2-based supercapacitors. Moreover, all components in the all-wood-structured ASC are low-cost, environmentally friendly and biocompatible. With these unique features, the all-wood-structured ASC represents a promising energy storage device to realize high mass loading, high energy/power density, and biocompatibility for green and renewable energy storage.

Conformal, Nanoscale ZnO Surface Modification of Garnet-Based Solid-State Electrolyte for Lithium Metal Anodes

Solid-state electrolytes are known for nonflammability, dendrite blocking, and stability over large potential windows. Garnet-based solid-state electrolytes have attracted much attention for their high ionic conductivities and stability with lithium metal anodes. However, high-interface resistance with lithium anodes hinders their application to lithium metal batteries. Here, we demonstrate an ultrathin, conformal ZnO surface coating by atomic layer deposition for improved wettability of garnet solid-state electrolytes to molten lithium that significantly decreases the interface resistance to as low as ∼20 Ω·cm2. The ZnO coating demonstrates a high reactivity with lithium metal, which is systematically characterized. As a proof-of-concept, we successfully infiltrated lithium metal into porous garnet electrolyte, which can potentially serve as a self-supported lithium metal composite anode having both high ionic and electrical conductivity for solid-state lithium metal batteries. The facile surface treatment method offers a simple strategy to solve the interface problem in solid-state lithium metal batteries with garnet solid electrolytes.

Reducing Interfacial Resistance between Garnet‐Structured Solid‐State Electrolyte and Li‐Metal Anode by a Germanium Layer

Substantial efforts are underway to develop all-solid-state Li batteries (SSLiBs) toward high safety, high power density, and high energy density. Garnet-structured solid-state electrolyte exhibits great promise for SSLiBs owing to its high Li-ion conductivity, wide potential window, and sufficient thermal/chemical stability. A major challenge of garnet is that the contact between the garnet and the Li-metal anodes is poor due to the rigidity of the garnet, which leads to limited active sites and large interfacial resistance. This study proposes a new methodology for reducing the garnet/Li-metal interfacial resistance by depositing a thin germanium (Ge) (20 nm) layer on garnet. By applying this approach, the garnet/Li-metal interfacial resistance decreases from ≈900 to ≈115 Ω cm2 due to an alloying reaction between the Li metal and the Ge. In agreement with experiments, first-principles calculation confirms the good stability and improved wetting at the interface between the lithiated Ge layer and garnet. In this way, this unique Ge modification technique enables a stable cycling performance of a full cell of lithium metal, garnet electrolyte, and LiFePO4 cathode at room temperature.

High-capacity, low-tortuosity, and channel-guided lithium metal anode

Significance Li metal is considered as the “Holy Grail” anode for Li batteries due to its highest theoretical capacity and lowest electrochemical potential. However, the infinite volume change during the Li stripping/plating process would lead to issues like solid electrolyte interphase cracks and Li dendrites. This work describes a high-capacity and low-tortuosity Li metal anode, which was prepared by infusing molten Li into carbonized wood channels. The straight channels of carbonized wood acting as an ideal host can effectively accommodate the Li volume change, which delivered a lower overpotential and better cycling performance compared with bare Li metal. This work demonstrated the importance of structure design, especially low-tortuosity Li metal structure, for enabling Li metal anode in high-energy batteries. Lithium metal anode with the highest capacity and lowest anode potential is extremely attractive to battery technologies, but infinite volume change during the Li stripping/plating process results in cracks and fractures of the solid electrolyte interphase, low Coulombic efficiency, and dendritic growth of Li. Here, we use a carbonized wood (C-wood) as a 3D, highly porous (73% porosity) conductive framework with well-aligned channels as Li host material. We discovered that molten Li metal can infuse into the straight channels of C-wood to form a Li/C-wood electrode after surface treatment. The C-wood channels function as excellent guides in which the Li stripping/plating process can take place and effectively confine the volume change that occurs. Moreover, the local current density can be minimized due to the 3D C-wood framework. Therefore, in symmetric cells, the as-prepared Li/C-wood electrode presents a lower overpotential (90 mV at 3 mA⋅cm−2), more-stable stripping/plating profiles, and better cycling performance (∼150 h at 3 mA⋅cm−2) compared with bare Li metal electrode. Our findings may open up a solution for fabricating stable Li metal anode, which further facilitates future application of high-energy-density Li metal batteries.

Highly Flexible and Efficient Solar Steam Generation Device

Solar steam generation with subsequent steam recondensation has been regarded as one of the most promising techniques to utilize the abundant solar energy and sea water or other unpurified water through water purification, desalination, and distillation. Although tremendous efforts have been dedicated to developing high-efficiency solar steam generation devices, challenges remain in terms of the relatively low efficiency, complicated fabrications, high cost, and inability to scale up. Here, inspired by the water transpiration behavior of trees, the use of carbon nanotube (CNT)-modified flexible wood membrane (F-Wood/CNTs) is demonstrated as a flexible, portable, recyclable, and efficient solar steam generation device for low-cost and scalable solar steam generation applications. Benefitting from the unique structural merits of the F-Wood/CNTs membrane-a black CNT-coated hair-like surface with excellent light absorbability, wood matrix with low thermal conductivity, hierarchical micro- and nanochannels for water pumping and escaping, solar steam generation device based on the F-Wood/CNTs membrane demonstrates a high efficiency of 81% at 10 kW cm-2 , representing one of the highest values ever-reported. The nature-inspired design concept in this study is straightforward and easily scalable, representing one of the most promising solutions for renewable and portable solar energy generation and other related phase-change applications.

3D‐Printed, All‐in‐One Evaporator for High‐Efficiency Solar Steam Generation under 1 Sun Illumination

Using solar energy to generate steam is a clean and sustainable approach to addressing the issue of water shortage. The current challenge for solar steam generation is to develop easy-to-manufacture and scalable methods which can convert solar irradiation into exploitable thermal energy with high efficiency. Although various material and structure designs have been reported, high efficiency in solar steam generation usually can be achieved only at concentrated solar illumination. For the first time, 3D printing to construct an all-in-one evaporator with a concave structure for high-efficiency solar steam generation under 1 sun illumination is used. The solar-steam-generation device has a high porosity (97.3%) and efficient broadband solar absorption (>97%). The 3D-printed porous evaporator with intrinsic low thermal conductivity enables heat localization and effectively alleviates thermal dissipation to the bulk water. As a result, the 3D-printed evaporator has a high solar steam efficiency of 85.6% under 1 sun illumination (1 kW m-2 ), which is among the best compared with other reported evaporators. The all-in-one structure design using the advanced 3D printing fabrication technique offers a new approach to solar energy harvesting for high-efficiency steam generation.

Three-dimensional bilayer garnet solid electrolyte based high energy density lithium metal–sulfur batteries

To simultaneously address the challenges of chemical/physical short circuits and electrode volume variation, we demonstrate a three-dimensional (3D) bilayer garnet solid-state electrolyte framework for advanced Li metal batteries. The dense layer is reduced in thickness to a few microns and still retains good mechanical stability, thereby enabling the safe use of Li metal anodes. The thick porous layer acts as a mechanical support for the thin dense layer which serves as a host for high loading of cathode materials and provides pathways for continuous ion transport. Results show that the integrated sulfur cathode loading can reach >7 mg cm−2 while the proposed hybrid Li–S battery exhibits a high initial coulombic efficiency (>99.8%) and high average coulombic efficiency (>99%) during the subsequent cycles. This electrolyte framework represents a promising strategy to revolutionize Li-metal batteries by transitioning to all-solid-state batteries and can be extended to other cathode materials.

Reduced Graphene Oxide Films with Ultrahigh Conductivity as Li-Ion Battery Current Collectors

Solution processed, highly conductive films are extremely attractive for a range of electronic devices, especially for printed macroelectronics. For example, replacing heavy, metal-based current collectors with thin, light, flexible, and highly conductive films will further improve the energy density of such devices. Films with two-dimensional building blocks, such as graphene or reduced graphene oxide (RGO) nanosheets, are particularly promising due to their low percolation threshold with a high aspect ratio, excellent flexibility, and low cost. However, the electrical conductivity of these films is low, typically less than 1000 S/cm. In this work, we for the first time report a RGO film with an electrical conductivity of up to 3112 S/cm. We achieve high conductivity in RGO films through an electrical current-induced annealing process at high temperature of up to 2750 K in less than 1 min of anneal time. We studied in detail the unique Joule heating process at ultrahigh temperature. Through a combination of experimental and computational studies, we investigated the fundamental mechanism behind the formation of a highly conductive three-dimensional structure composed of well-connected RGO layers. The highly conductive RGO film with high direct current conductivity, low thickness (∼4 μm) and low sheet resistance (0.8 Ω/sq.) was used as a lightweight current collector in Li-ion batteries.

A carbon-based 3D current collector with surface protection for Li metal anode

Lithium metal is considered the ideal anode material for Li-ion-based batteries because it exhibits the highest specific capacity and lowest redox potential for this type of cells. However, growth of Li dendrites, unstable solid electrolyte interphases, low Coulombic efficiencies, and safety hazards have significantly hindered the practical application of metallic Li anodes. Herein, we propose a three-dimensional (3D) carbon nanotube sponge (CNTS) as a Li deposition host. The high specific surface area of the CNTS enables homogenous charge distribution for Li nucleation and minimizes the effective current density to overcome dendrite growth. An additional conformal Al2O3 layer on the CNTS coated by atomic layer deposition (ALD) robustly protects the Li metal electrode/electrolyte interface due to the good chemical stability and high mechanical strength of the layer. The Li@ALD-CNTS electrode exhibits stable voltage profiles with a small overpotential ranging from 16 to 30 mV over 100 h of cycling at 1.0 mA·cm–2. Moreover, the electrodes display a dendrite-free morphology after cycling and a Coulombic efficiency of 92.4% over 80 cycles at 1.0 mA·cm–2 in an organic carbonate electrolyte, thus demonstrating electrochemical stability superior to that of planar current collectors. Our results provide an important strategy for the rational design of current collectors to obtain stable Li metal anodes.