Yılmaz Yalçin

Investigation of corrosion behaviors at different solutions of boronized AISI 316L stainless steel

In this study, corrosion behaviors of boronized and non-boronized AISI 316L stainless steel (AISI 316L SS) were investigated with Tafel extrapolation and linear polarization methods in different solutions (1 mol dm−3 HCl, 1 mol dm−3 NaOH and 0.9% NaCl) and in different immersion times. AISI 316L SS were boronized by using pack boronizing method for 2 and 6 hours at 800 and 900°C within commercial Ekabor®-2 powder. Surface morphologies and phase analyses of boride layers on the surface of AISI 316L SS were characterized by scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) analysis. SEM-EDS analyses show that boride layer on AISI 316L SS surface had a flat and smooth morphology. It was detected by XRD analyses that boride layer contained FeB, Fe2B, CrB, Cr2B, NiB and Ni2B phases. Boride layer thickness increases with increased boronizing temperature and time. The corrosion experiments show that boride layer significantly increased the corrosion resistance of the AISI 316L SS in 1 mol dm−3 HCl solution. While no positive effect of the boride layer was observed in the other solutions the corrosion resistance of the borid layer on AISI 316L SS was increased in all solution with the increase of the waiting periods.

Corrosion and wear behaviors of boronized AISI 316L stainless steel

In this study, the effects of a boronizing treatment on the corrosion and wear behaviors of AISI 316L austenitic stainless steel (AISI 316L) were examined. The corrosion behavior of the boronized samples was studied via electrochemical methods in a simulation body fluid (SBF) and the wear behavior was examined using the ball-on-disk wear method. It was observed that the boride layer that formed on the AISI 316L surface had a flat and smooth morphology. Furthermore, X-ray diffraction analyses show that the boride layer contained FeB, Fe2B, CrB, Cr2B, NiB, and Ni2B phases. Boride layer thickness increased with an increasing boronizing temperature and time. The boronizing treatment also increased the surface hardness of the AISI 316L. Although there was no positive effect of the coating on the corrosion resistance in the SBF medium. Furthermore, a decrease in the friction coefficient was recorded for the boronized AISI 316L. As the boronizing temperature increased, the wear rate decreased in both dry and wet mediums. As a result, the boronizing treatment contributed positively to the wear resistance by increasing the surface hardness and by decreasing the friction coefficient of the AISI 316L.

Effects of minor Cu and Si additions on glass forming ability and mechanical properties of Co-Fe-Ta-B Bulk metallic glass

Effect of Cu and Si substitutions for Co and B on the glass forming ability (GFA) of Co(43-x)CuxFe20Ta5.5B(31.5-x)Siy (x=0-1.5 and y=5-10) were systematically investigated by X-ray diffraction, optical microscopy, scanning electron microscopy, and differential scanning calorimetry. In order to evaluate the contribution of copper and silicon, appropriate amounts of copper and silicon were individually introduced to the base alloy composition. By using the effects of copper and silicon together, significant enhancement was obtained and the critical casting thickness (CCT) of the base alloy was increased three times from 2 mm to 6 mm. Moreover, mechanical properties of the alloys were examined by compression tests and Vickers hardness measurements. The compression test results revealed that the glassy alloys having enhanced GFA shows high strength of about 3500-4000 MPa. In addition, existence of (Co,Fe)2B and (Co,Fe)20.82Ta2.18B6 crystalline phases in glassy matrix influences the hardnesses of the alloys compared to monolitic glassy structure having hardness of about 1200 Hv.

Corrosion behavior of boro-tempered ductile iron

In this study, the effect of boro-tempering heat treatment on the microstructure and corrosion behavior of unalloyed ductile iron was investigated. The corrosion characteristics of ductile iron have been determined by current-potential curves. To determine the corrosion rates, the anodic and cathodic Tafel regions extrapolating to corrosion potentials were used. The inhibitor efficiency was calculated from icorr values. Optical microscope and X-ray diffraction (XRD) were used to examine the microstructure of polished and etched specimens. Thicknesses of the boride layers formed on samples were measured by an optical micrometer attached to the optical microscope. Results show that boro-tempering heat treatment can be successfully applied to ductile iron. The corrosion potential has shifted to more positive values in the boronized samples. The boride layer has behaved like an anodic inhibitor. The boronizing time has affected the corrosion rate. The increase in boronizing time has made the coating thicker, which has increased the corrosion resistance of the material. The best inhibition and the lowest corrosion rate have been performed on the sample which was boronized for 5 hours after cooling in furnace. The tempering at higher temperatures leads to an increase in the corrosion resistance of the materials tested here.