Yong-Young Noh

Flexible metal-oxide devices made by room-temperature photochemical activation of sol-gel films

Amorphous metal-oxide semiconductors have emerged as potential replacements for organic and silicon materials in thin-film electronics. The high carrier mobility in the amorphous state, and excellent large-area uniformity, have extended their applications to active-matrix electronics, including displays, sensor arrays and X-ray detectors. Moreover, their solution processability and optical transparency have opened new horizons for low-cost printable and transparent electronics on plastic substrates. But metal-oxide formation by the sol–gel route requires an annealing step at relatively high temperature, which has prevented the incorporation of these materials with the polymer substrates used in high-performance flexible electronics. Here we report a general method for forming high-performance and operationally stable metal-oxide semiconductors at room temperature, by deep-ultraviolet photochemical activation of sol–gel films. Deep-ultraviolet irradiation induces efficient condensation and densification of oxide semiconducting films by photochemical activation at low temperature. This photochemical activation is applicable to numerous metal-oxide semiconductors, and the performance (in terms of transistor mobility and operational stability) of thin-film transistors fabricated by this route compares favourably with that of thin-film transistors based on thermally annealed materials. The field-effect mobilities of the photo-activated metal-oxide semiconductors are as high as 14 and 7 cm2 V−1 s−1 (with an Al2O3 gate insulator) on glass and polymer substrates, respectively; and seven-stage ring oscillators fabricated on polymer substrates operate with an oscillation frequency of more than 340 kHz, corresponding to a propagation delay of less than 210 nanoseconds per stage.

Organic Light Detectors: Photodiodes and Phototransistors

While organic electronics is mostly dominated by light-emitting diodes, photovoltaic cells and transistors, optoelectronics properties peculiar to organic semiconductors make them interesting candidates for the development of innovative and disruptive applications also in the field of light signal detection. In fact, organic-based photoactive media combine effective light absorption in the region of the spectrum from ultraviolet to near-infrared with good photogeneration yield and low-temperature processability over large areas and on virtually every substrate, which might enable innovative optoelectronic systems to be targeted for instance in the field of imaging, optical communications or biomedical sensing. In this review, after a brief resume of photogeneration basics and of devices operation mechanisms, we offer a broad overview of recent progress in the field, focusing on photodiodes and phototransistors. As to the former device category, very interesting values for figures of merit such as photoconversion efficiency, speed and minimum detectable signal level have been attained, and even though the simultaneous optimization of all these relevant parameters is demonstrated in a limited number of papers, real applications are within reach for this technology, as it is testified by the increasing number of realizations going beyond the single-device level and tackling more complex optoelectronic systems. As to phototransistors, a more recent subject of study in the framework of organic electronics, despite a broad distribution in the reported performances, best photoresponsivities outperform amorphous silicon-based devices. This suggests that organic phototransistors have a large potential to be used in a variety of optoelectronic peculiar applications, such as a photo-sensor, opto-isolator, image sensor, optically controlled phase shifter, and opto-electronic switch and memory.

Downscaling of self-aligned, all-printed polymer thin-film transistors

Printing is an emerging approach for low-cost, large-area manufacturing of electronic circuits, but it has the disadvantages of poor resolution, large overlap capacitances, and film thickness limitations, resulting in slow circuit speeds and high operating voltages. Here, we demonstrate a self-aligned printing approach that allows downscaling of printed organic thin-film transistors to channel lengths of 100-400 nm. The use of a crosslinkable polymer gate dielectric with 30-50 nm thickness ensures that basic scaling requirements are fulfilled and that operating voltages are below 5 V. The device architecture minimizes contact resistance effects, enabling clean scaling of transistor current with channel length. A self-aligned gate configuration minimizes parasitic overlap capacitance to values as low as 0.2-0.6 pF mm(-1), and allows transition frequencies of fT = 1.6 MHz to be reached. Our self-aligned process provides a way to improve the performance of printed organic transistor circuits by downscaling, while remaining compatible with the requirements of large-area, flexible electronics manufacturing.

A Thienoisoindigo-Naphthalene Polymer with Ultrahigh Mobility of 14.4 cm2/V·s That Substantially Exceeds Benchmark Values for Amorphous Silicon Semiconductors

By considering the qualitative benefits associated with solution rheology and mechanical properties of polymer semiconductors, it is expected that polymer-based electronic devices will soon enter our daily lives as indispensable elements in a myriad of flexible and ultra low-cost flat panel displays. Despite more than a decade of research focused on designing and synthesizing state-of-the-art polymer semiconductors for improving charge transport characteristics, the current mobility values are still not sufficient for many practical applications. The confident mobility in excess of ∼10 cm(2)/V·s is the most important requirement for enabling the realization of the aforementioned near-future products. We report on an easily attainable donor-acceptor (D-A) polymer semiconductor: poly(thienoisoindigo-alt-naphthalene) (PTIIG-Np). An unprecedented mobility of 14.4 cm(2)/V·s, by using PTIIG-Np with a high-k gate dielectric poly(vinylidenefluoride-trifluoroethylene) (P(VDF-TrFE)), is achieved from a simple coating processing, which is of a magnitude that is very difficult to obtain with conventional TFTs by means of molecular engineering. This work, therefore, represents a major step toward truly viable plastic electronics.

Energy transfer and device performance in phosphorescent dye doped polymer light emitting diodes

Singlet and triplet–triplet energy transfer in phosphorescent dye doped polymer light emitting devices were investigated. Poly(N-vinylcarbazol) and poly[9,9′-di-n-hexyl-2,7-fluorene-alt- 1,4-(2,5-di-n-hexyloxy)phenylene] (PFHP) were selected as the host polymer for the phosphorescent dopants fac-tris(2-phenylpyridine) iridium(III) [Ir(ppy)3] and 2,3,7,8,12,13, 17,18-octaethyl-21H,23H-porphyrin platinum(II) (PtOEP) because of their high triplet energy levels and long phosphorescence lifetimes. In case of PVK film, efficient triplet energy transfers to both PtOEP and Ir(ppy)3 were observed. In contrast, the triplet energy transfer did not occur or was very weak from PFHP to both PtOEP and Ir(ppy)3 although usual requirements for triplet energy transfer were satisfied. Furthermore, the singlet–singlet energy transfer did not take place from PFHP to Ir(ppy)3 in doped films even though the Forster radius is more than 30 A. However, the blended film of Ir(ppy)3 with PFHP and PMMA showed the green emission from ...

Large-scale organic nanowire lithography and electronics

Controlled alignment and patterning of individual semiconducting nanowires at a desired position in a large area is a key requirement for electronic device applications. High-speed, large-area printing of highly aligned individual nanowires that allows control of the exact numbers of wires, and their orientations and dimensions is a significant challenge for practical electronics applications. Here we use a high-speed electrohydrodynamic organic nanowire printer to print large-area organic semiconducting nanowire arrays directly on device substrates in a precisely, individually controlled manner; this method also enables sophisticated large-area nanowire lithography for nano-electronics. We achieve a maximum field-effect mobility up to 9.7 cm(2) V(-1) s(-1) with extremely low contact resistance (<5.53 Ω cm), even in nano-channel transistors based on single-stranded semiconducting nanowires. We also demonstrate complementary inverter circuit arrays comprising well-aligned p-type and n-type organic semiconducting nanowires. Extremely fast nanolithography using printed semiconducting nanowire arrays provide a simple, reliable method of fabricating large-area and flexible nano-electronics.

Highly sensitive thin-film organic phototransistors: Effect of wavelength of light source on device performance

Organic phototransistors (OPTs) were fabricated from pentacene and copper phthalocyanine (CuPC) based on the geometry of organic field-effect transistors (OFETs); and the effect of the wavelength of the incident light source on their performance was examined. High performance OFETs with pentacene and CuPC were fabricated and the characteristics of the OPTs were examined under UV and visible-light irradiations with top illumination. The CuPC and pentacene OPTs show a high responsivities of 0.5–2 and 10–50A∕W and maximum IPh∕IDark of 3000 and 1.3×105, respectively, under 365nm UV light. However, under visible light, at a wavelength of 650nm, the pentacene OPTs had 100 times less responsivity, 0.15–0.45A∕W, and a IPh∕IDark of 1000, even though an absorption coefficient three times larger was observed at this wavelength than at 365nm. A strong correlation was found between the performance of the OPTs and the incident photon to current conversion efficiency spectra of an organic semiconductor. The strong depen...

Dramatic inversion of charge polarity in diketopyrrolopyrrole-based organic field-effect transistors via a simple nitrile group substitution.

A record-breaking high electron mobility of 7.0 cm(2) V(-1) s(-1) for n-channel polymer OFETs is reported. By the incorporation of only one nitrile group as an electron-withdrawing function in the vinyl linkage of the DPP-based copolymer, a dramatic inversion of majority charge-carriers from holes to electrons is achieved.

Remarkable Enhancement of Hole Transport in Top‐Gated N‐Type Polymer Field‐Effect Transistors by a High‐k Dielectric for Ambipolar Electronic Circuits

A remarkable enhancement of p-channel properties is achieved in initially n-channel dominant ambipolar P(NDI2OD-T2) organic field-effect transistors (OFETs) by the use of the fluorinated high-k dielectric P(VDF-TrFE). An almost two orders of magnitude increase in hole mobility (~0.11 cm(2) V(-1) s(-1) ) originates from a strong interface modification at the semiconductor/dielectric interface, which provides high-performance complementary-like inverters and ring oscillator circuits.

High-photosensitivity p-channel organic phototransistors based on a biphenyl end-capped fused bithiophene oligomer

We report highly photosensitive organic phototransistors (OPTs) based on a 2,5-bis-biphenyl-4-yl-thieno[3,2-b]thiophene (BPTT). The measured maximum sensitivity and the ratio of photocurrent to dark current (Iph∕Idark) in BPTT OPTs were 82A∕W and 2.0×105 under 380nm UV light with 1.55mW∕cm2, respectively. The prepared OPTs show a photocurrent response similar to the absorption spectrum of BPTT. The major mechanisms for photocurrent amplification in this device were verified from experimental results as photovoltaic (turn-on) and photocurrent effect (turn-off) by a fitting to theoretic equations.