Yongsheng Liu

Interface engineering of highly efficient perovskite solar cells

A layered approach improves solar cells Perovskite films received a boost in photovoltaic efficiency through controlled formation of charge-generating films and improved current transfer to the electrodes. Zhou et al. lowered the defect density of the film by controlling humidity while the perovskite film formed from lead chloride and methylammonium iodide. Low-temperature processing steps allowed the use of materials that draw current out of the perovskite layer more efficiently. These and other modifications enabled a maximum cell efficiency of just over 19% and an average of 16.6%. Science, this issue p. 542 Optimizing the growth conditions of the perovskite layer and interlayer carrier transport boosts solar cell efficiency. Advancing perovskite solar cell technologies toward their theoretical power conversion efficiency (PCE) requires delicate control over the carrier dynamics throughout the entire device. By controlling the formation of the perovskite layer and careful choices of other materials, we suppressed carrier recombination in the absorber, facilitated carrier injection into the carrier transport layers, and maintained good carrier extraction at the electrodes. When measured via reverse bias scan, cell PCE is typically boosted to 16.6% on average, with the highest efficiency of ~19.3% in a planar geometry without antireflective coating. The fabrication of our perovskite solar cells was conducted in air and from solution at low temperatures, which should simplify manufacturing of large-area perovskite devices that are inexpensive and perform at high levels.

Improved air stability of perovskite solar cells via solution-processed metal oxide transport layers

Lead halide perovskite solar cells have recently attracted tremendous attention because of their excellent photovoltaic efficiencies. However, the poor stability of both the perovskite material and the charge transport layers has so far prevented the fabrication of devices that can withstand sustained operation under normal conditions. Here, we report a solution-processed lead halide perovskite solar cell that has p-type NiO(x) and n-type ZnO nanoparticles as hole and electron transport layers, respectively, and shows improved stability against water and oxygen degradation when compared with devices with organic charge transport layers. Our cells have a p-i-n structure (glass/indium tin oxide/NiO(x)/perovskite/ZnO/Al), in which the ZnO layer isolates the perovskite and Al layers, thus preventing degradation. After 60 days storage in air at room temperature, our all-metal-oxide devices retain about 90% of their original efficiency, unlike control devices made with organic transport layers, which undergo a complete degradation after just 5 days. The initial power conversion efficiency of our devices is 14.6 ± 1.5%, with an uncertified maximum value of 16.1%.

Planar Heterojunction Perovskite Solar Cells via Vapor-Assisted Solution Process

Hybrid organic/inorganic perovskites (e.g., CH3NH3PbI3) as light absorbers are promising players in the field of third-generation photovoltaics. Here we demonstrate a low-temperature vapor-assisted solution process to construct polycrystalline perovskite thin films with full surface coverage, small surface roughness, and grain size up to microscale. Solar cells based on the as-prepared films achieve high power conversion efficiency of 12.1%, so far the highest efficiency based on CH3NH3PbI3 with the planar heterojunction configuration. This method provides a simple approach to perovskite film preparation and paves the way for high reproducibility of films and devices. The underlying kinetic and thermodynamic parameters regarding the perovskite film growth are discussed as well.

Controllable self-induced passivation of hybrid lead iodide perovskites toward high performance solar cells.

To improve the performance of the polycrystalline thin film devices, it requires a delicate control of its grain structures. As one of the most promising candidates among current thin film photovoltaic techniques, the organic/inorganic hybrid perovskites generally inherit polycrystalline nature and exhibit compositional/structural dependence in regard to their optoelectronic properties. Here, we demonstrate a controllable passivation technique for perovskite films, which enables their compositional change, and allows substantial enhancement in corresponding device performance. By releasing the organic species during annealing, PbI2 phase is presented in perovskite grain boundaries and at the relevant interfaces. The consequent passivation effects and underlying mechanisms are investigated with complementary characterizations, including scanning electron microscopy (SEM), X-ray diffraction (XRD), time-resolved photoluminescence decay (TRPL), scanning Kelvin probe microscopy (SKPM), and ultraviolet photoemission spectroscopy (UPS). This controllable self-induced passivation technique represents an important step to understand the polycrystalline nature of hybrid perovskite thin films and contributes to the development of perovskite solar cells judiciously.

Solution-processed small-molecule solar cells: breaking the 10% power conversion efficiency.

A two-dimensional conjugated small molecule (SMPV1) was designed and synthesized for high performance solution-processed organic solar cells. This study explores the photovoltaic properties of this molecule as a donor, with a fullerene derivative as an acceptor, using solution processing in single junction and double junction tandem solar cells. The single junction solar cells based on SMPV1 exhibited a certified power conversion efficiency of 8.02% under AM 1.5 G irradiation (100 mW cm−2). A homo-tandem solar cell based on SMPV1 was constructed with a novel interlayer (or tunnel junction) consisting of bilayer conjugated polyelectrolyte, demonstrating an unprecedented PCE of 10.1%. These results strongly suggest solution-processed small molecular materials are excellent candidates for organic solar cells.

Small Molecules Based on Benzo(1,2-b:4,5-b')dithiophene Unit for High-Performance Solution-Processed Organic Solar Cells

Small molecules, namely, DCAO(3)TBDT and DR(3)TBDT, with 2-ethylhexoxy substituted BDT as the central building block and octyl cyanoacetate and 3-ethylrhodanine as different terminal units with the same linkage of dioctyltertthiophene, have been designed and synthesized. The photovoltaic properties of these two molecules as donors and fullerene derivatives as the acceptors in bulk heterojunction solar cells are studied. Among them, DR(3)TBDT shows excellent photovoltaic performance, and power conversion efficiency as high as 7.38% (certified 7.10%) under AM 1.5G irradiation (100 mW cm(-2)) has been achieved using the simple solution spin-coating fabrication process, which is the highest efficiency reported to date for any small-molecule-based solar cells. The results demonstrate that structure fine turning could cause significant performance difference and with that the performance of solution-processed small-molecule solar cells can indeed be comparable with or even surpass their polymer counterparts.

Moisture assisted perovskite film growth for high performance solar cells

Moisture is assumed to be detrimental to organometal trihalide perovskite, as excess water can damage the crystallinity of the perovskite structure. Here, we report a growth mode for via thermal annealing of the perovskite precursor film in a humid environment (e.g., ambient air) to greatly improve the film quality, grain size, carrier mobility, and lifetime. Our method produces devices with maximum power conversion efficiency of 17.1% and a fill factor of 80%, revealing a promising route to achieve high quality perovskite polycrystalline films with superior optoelectronic properties that can pave the way towards efficient photovoltaic conversion.

High‐Performance Solar Cells using a Solution‐Processed Small Molecule Containing Benzodithiophene Unit

A conjugated small molecule containing a benzodithiophene unit shows high performance in bulk heterojunction (BHJ) solar cells. Using the simple solution spinning process, a high PCE is achieved by employing this molecule as the donor in BHJ solar cells.

Synthesis of 5H-Dithieno[3,2-b:2′,3′-d]pyran as an Electron-Rich Building Block for Donor–Acceptor Type Low-Bandgap Polymers

We describe the detailed synthesis and characterization of an electron-rich building block, dithienopyran (DTP), and its application as a donor unit in lowbandgap conjugated polymers. The electron-donating property of the DTP unit was found to be the strongest among the most frequently used donor units such as benzodithiophene (BDT) or cyclopentadithiophene (CPDT) units. When the DTP unit was polymerized with the strongly electron-deficient difluorobenzothiadiazole (DFBT) unit, a regiorandom polymer (PDTP−DFBT, bandgap = 1.38 eV) was obtained. For comparison with the DTP unit, polymers containing alternating benzodithiophene (BDT) or cyclopentadithiophene (CPDT) units and the DFBT unit were synthesized (PBDT−DFBT and PCPDT−DFBT). We found that the DTP based polymer PDTP−DFBT shows significantly improved solubility and processability compared to the BDT or CPDT based polymers. Consequently, very high molecular weight and soluble PDTP−DFBT can be obtained with less bulky side chains. Interestingly, PDTP−DFBT shows excellent performance in bulk-heterojunction solar cells with power conversion efficiencies reaching 8.0%, which is significantly higher than PBDT−DFBT and PCPDT−DFBT based devices. This study demonstrates that DTP is a promising building block for high-performance solar cell materials.

Perovskite solar cells: film formation and properties

Perovskite solar cells have received considerable attention in recent years as a promising material capable of developing high performance photovoltaic devices at a low cost. Their high absorption coefficient, tunable band gap, low temperature processing and abundant elemental constituents provide numerous advantages over most thin film absorber materials. In this review, we discuss the current status of CH3NH3PbX3 (X = I, Br, Cl) based photovoltaic devices and provide a comprehensive review of CH3NH3PbX3 device structures, film properties, fabrication methods, and photovoltaic performance. We emphasize the importance of perovskite film formation and properties in achieving highly efficient photovoltaic devices. The flexibility and simplicity of perovskite fabrication methods allow use of mesoporous and planar device architectures. A variety of processing techniques are currently employed to form the highest quality CH3NH3PbX3 films that include precursor modifications, thermal annealing and post-deposition treatments. Here we outline and discuss the resulting material qualities and device performances. Suggestions regarding needed improvements and future research directions are provided based on the current field of available literature.