Yoonmook Kang

Hybrid solar cells with vertically aligned CdTe nanorods and a conjugated polymer

Vertically aligned CdTe nanorods were fabricated by electrodeposition and were applied for the active layer of solar cells after being combined with poly(3-octylthiophene) (P3OT), a conjugated polymer. The electrodeposited CdTe showed an n-type behavior with the electric resistivity and the electron density of 2×106Ωcm, 1.3×1010cm−3, respectively. Quantum efficiency curve of the hybrid solar cells exhibited a peak at the same wavelength as the optical absorption for CdTe nanorods. The hybrid solar cells demonstrated a power conversion efficiency of 1.06%, whereas the efficiency was only 0.0006% without the nanorods.

UV Degradation and Recovery of Perovskite Solar Cells

Although the power conversion efficiency of perovskite solar cells has increased from 3.81% to 22.1% in just 7 years, they still suffer from stability issues, as they degrade upon exposure to moisture, UV light, heat, and bias voltage. We herein examined the degradation of perovskite solar cells in the presence of UV light alone. The cells were exposed to 365 nm UV light for over 1,000 h under inert gas at <0.5 ppm humidity without encapsulation. 1-sun illumination after UV degradation resulted in recovery of the fill factor and power conversion efficiency. Furthermore, during exposure to consecutive UV light, the diminished short circuit current density (Jsc) and EQE continuously restored. 1-sun light soaking induced recovery is considered to be caused by resolving of stacked charges and defect state neutralization. The Jsc and EQE bounce-back phenomenon is attributed to the beneficial effects of PbI2 which is generated by the decomposition of perovskite material.

Electric-Field-Induced Degradation of Methylammonium Lead Iodide Perovskite Solar Cells

Perovskite solar cells have great potential for high efficiency generation but are subject to the impact of external environmental conditions such as humidity, UV and sun light, temperature, and electric fields. The long-term stability of perovskite solar cells is an important issue for their commercialization. Various studies on the stability of perovskite solar cells are currently being performed; however, the stability related to electric fields is rarely discussed. Here the electrical stability of perovskite solar cells is studied. Ion migration is confirmed using the temperature-dependent dark current decay. Changes in the power conversion efficiency according to the amount of the external bias are measured in the dark, and a significant drop is observed only at an applied voltage greater than 0.8 V. We demonstrate that perovskite solar cells are stable under an electric field up to the operating voltage.

Effects of myosin heavy chain isoforms on meat quality, fatty acid composition, and sensory evaluation in Berkshire pigs.

The main objective of this study was to investigate the effects of myosin heavy chain (MHC) isoforms on meat and sensory quality in Berkshire pigs. A total of 85 pigs were evaluated, and muscle samples were taken for the analyses of MHC isoform, meat quality, fatty acid composition, and sensory evaluation. Content of the MHC slow isoform was significantly correlated with pH(24h) (r=0.26, P<0.05) and drip loss (r=-0.32, P<0.01), although the content of MHC isoforms showed limited relationships with individual fatty acids. In the case of sensory evaluation of meat by a trained panel test, the MHC fast/slow ratio was correlated with the juiciness (r=-0.33, P<0.01), off-flavor (r=0.34, P<0.01), tenderness attributes (r=-0.43 to -0.47). These results imply that the content of MHC isoforms can influence various aspects of quality including pork and sensory quality in Berkshire pigs.

Relationship between ion migration and interfacial degradation of CH 3 NH 3 PbI 3 perovskite solar cells under thermal conditions

Organic-inorganic hybrid perovskite solar cells (PSCs) have been extensively studied because of their outstanding performance: a power conversion efficiency exceeding 22% has been achieved. The most commonly used PSCs consist of CH3NH3PbI3 (MAPbI3) with a hole-selective contact, such as 2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenylamine)-9,9-spiro-bifluorene (spiro-OMeTAD), for collecting holes. From the perspective of long-term operation of solar cells, the cell performance and constituent layers (MAPbI3, spiro-OMeTAD, etc.) may be influenced by external conditions like temperature, light, etc. Herein, we report the effects of temperature on spiro-OMeTAD and the interface between MAPbI3 and spiro-OMeTAD in a solar cell. It was confirmed that, at high temperatures (85 °C), I− and CH3NH3+ (MA+) diffused into the spiro-OMeTAD layer in the form of CH3NH3I (MAI). The diffused I− ions prevented oxidation of spiro-OMeTAD, thereby degrading the electrical properties of spiro-OMeTAD. Since ion diffusion can occur during outdoor operation, the structural design of PSCs must be considered to achieve long-term stability.

Investigation of Thermally Induced Degradation in CH 3 NH 3 PbI 3 Perovskite Solar Cells using In-situ Synchrotron Radiation Analysis

In this study, we employ a combination of various in-situ surface analysis techniques to investigate the thermally induced degradation processes in MAPbI3 perovskite solar cells (PeSCs) as a function of temperature under air-free conditions (no moisture and oxygen). Through a comprehensive approach that combines in-situ grazing-incidence wide-angle X-ray diffraction (GIWAXD) and high-resolution X-ray photoelectron spectroscopy (HR-XPS) measurements, we confirm that the surface structure of MAPbI3 perovskite film changes to an intermediate phase and decomposes to CH3I, NH3, and PbI2 after both a short (20 min) exposure to heat stress at 100 °C and a long exposure (>1 hour) at 80 °C. Moreover, we observe clearly the changes in the orientation of CH3NH3+ organic cations with respect to the substrate in the intermediate phase, which might be linked directly to the thermal degradation processes in MAPbI3 perovskites. These results provide important progress towards improved understanding of the thermal degradation mechanisms in perovskite materials and will facilitate improvements in the design and fabrication of perovskite solar cells with better thermal stability.

Direct evidence of void passivation in Cu(InGa)(SSe)2 absorber layers

We have investigated the charge collection condition around voids in copper indium gallium sulfur selenide (CIGSSe) solar cells fabricated by sputter and a sequential process of selenization/sulfurization. In this study, we found direct evidence of void passivation by using the junction electron beam induced current method, transmission electron microscopy, and energy dispersive X-ray spectroscopy. The high sulfur concentration at the void surface plays an important role in the performance enhancement of the device. The recombination around voids is effectively suppressed by field-assisted void passivation. Hence, the generated carriers are easily collected by the electrodes. Therefore, when the S/(S + Se) ratio at the void surface is over 8% at room temperature, the device performance degradation caused by the recombination at the voids is negligible at the CIGSSe layer.

Light-induced degradation and metastable-state recovery with reaction kinetics modeling in boron-doped Czochralski silicon solar cells

Solar cells fabricated from boron-doped p-type Czochralski silicon suffer from light-induced degradation that can lower the conversion efficiency by up to 10% relative. When solar cells are exposed to temperatures between 100 °C and 200 °C under illumination, regeneration, in which the minority carrier lifetime is gradually recovered, occurs after the initial light-induced degradation. We studied the light-induced degradation and regeneration process using carrier injection within a design chamber and observed open-circuit voltage trends at various sample temperatures. We proposed a cyclic reaction kinetics model to more precisely analyze the degradation and recovery phenomenon. Our model incorporated the reaction paths that were not counted in the original model between the three states (annealed, degradation, and regeneration). We calculated a rate constant for each reaction path based on the proposed model, extracted an activation energy for each reaction using these rate constants at various temperatures, and calculated activation energies of redegradation and the stabilization reaction.

Effects of Current-injection Firing with Ag Paste in a Boron Emitter

A high contact resistance for screen-printed contacts was observed when a conventional Ag paste was used on a boron emitter. The results of this study suggest that electron injection during firing is one of the processes that contribute to a lower contact resistance. Larger quantities of Ag precipitates formed upon electron injection into the boron emitter, which was confirmed by observing Ag crystallite or dendrite structures on the boron and by measuring the contact resistance between the boron emitter and the Ag bulk. The electron-injected sample had approximately 10000 times lower contact resistance than an untreated sample. The contact resistance of the electron-injected sample was 0.021 mΩ∙cm2 under optimal conditions, which is lower than that of conventional p-type silicon solar cells. Thus, electron injection can effectively lower contact resistance when using Ag paste in n-type silicon solar cells. During the cooling in the firing process, dissolved Ag ions in the glass layer are formed as dendrites or crystallites/particles. The dendrites are formed earlier than others via electrochemical migration under electron injection conditions. Then, crystallites and particles are formed via a silicon etching reaction. Thus, Ag ions that are not formed as dendrites will form as crystallites or particles.

Simulation of interdigitated back contact solar cell with trench structure

We performed two-dimensional technology computer-aided design simulations for interdigitated back contact (IBC) solar cells with rear trench structures (TS), denoted here as TS-IBC solar cells. First, we calculated a reference simulation model for conventional IBC solar cells. We then assumed a trench structure at the rear surface of the IBC solar cell. For this structure, we analyzed solar cell performance as a function of various trench depths and type. It was found that emitter trench formation affects minority carrier collection, such that the short-circuit current density increases with increasing trench depth. However, the back-surface field (BSF) trench exhibited poor minority carrier collection, which reduced the conversion efficiency of the TS-IBC solar cells. It was also found that for the same trench depth (30 μm), the difference in conversion efficiencies of an IBC solar cell with an emitter trench and that with a BSF trench was 0.6%. We are thus convinced that the emitter trench structure is ...